Guitar Parts & Pickups

Strat style 4 bolt neck plate. (Mounting hardware not included). Four ¼” mounting holes. Made in Korea

Tele style control plate. 5.9” plate mounting center distance (0.123” diameter, recessed).

• Two potentiometer mounting holes for 3/8” bushing diameters
• One standard selector switch mounting slot (1.63” mounting center distance, 0.15” diameter, recessed)
• Made in Korea

5-way switch for Strats, black tip.

Replacement jack plate for Stratocasters

Standard (4-hole) and vintage (3-hole) versions. Replacement for most Jazz Bass style guitars. Made in Korea.

Blank pickguard material sheets for cutting custom pickguards, truss rod covers, and back plates. These sheets come in a variety of colors as well as single ply and three ply options. All colors feature a gloss surface.

Tremolo tension springs. Similar to P-GTSPRN-5 but generic manufacture.

Bone nut for Fender® , 44.45mm x 3.3mm x 6.35mm with radiused bottom.

Bone nut for Fender® , 44.45mm x 3.3mm x 6.35mm at highest point with flat bottom.

This modern cupstyle Tele® jackplate is milled from brass and has a shiny plated finish. Mounts with (2) screws that are included. No more having to deal with that sharp piece of steel used to secure the old original cups. Super easy to install! The cup is even threaded so no need for the lockwasher and nut from the jack. Just simply screw the jack into the cup, solder the wires and install into your instrument!

Jaguar style master control plate in chrome. Perfect replacement for most Jaguar style guitars. 4.12” x 1.86” plate mounting center distance (0.14” diameter, recessed).

Stratocaster style 3 ply pickguard with 11 mounting holes. Top and bottom layers are the same with an alternate middle layer.

Graphite nut for Fender® This graphite nut will work for most Fender® and similar style guitars. It is slotted, but does require final shaping and fitting to exact size.
PLEASE NOTE: Because this nut tapers in both thickness from top to bottom and height on the fret board side vs. the headstock side all measurements for those dimensions were taken at the center of the nut.

• Length = 1 41/64 inches (41.52mm)
• Height #1 (fretboard side) = 13/64 inches (5.06mm)
• Height #2 (headstock side) = 13/64 inches (5mm)
• Thickness at bottom = 9/64 inches (3.46mm)
• Thickness at top = 1/8 inches (3.1mm)

Tremolo Arm, Screw-Down, Steel 5mm-0.8p

• Material: Steel 5mm
• Handle Type: Screw-down
• Thread: M5.0 - 0.8p
• Plating: Chrome
• Tip: White

Replacement pickguard for Fender® Standard Stratocaster models. These pickguards have eleven mounting holes and are cut for the classic strat configuration. Fits most American and Mexican Standard Stratocasters®. Features:

• 3-ply / 2.5mm thickness
• 11 mounting holes
• Shielding over electronics cavity
• Fits 3/8" bushing pots
• Various colors available

Stratocaster guitar nut - plastic construction

Three-ply black/white/black ’62 Telecaster style pickguard with 8 mounting holes. This pickguard has no pickup mounting holes for use with neck pickups that mount directly to the guitar’s body.

This brass nut blank will work for most Fender® and similar style guitars and basses. It is NOT slotted and does require final shaping and fitting to exact size.

• Thickness = 9/64 inches (3.47mm)
• Flat Bottom Length = 1 11/16 inches (43 mm)
• Height at ends = 13/64 inches (5.25mm)
• Height at middle = 15/64 inches (6mm)

Blank thin pickguard material sheets with adhesive backing for acoustic guitars. The pre-applied adhesive makes for a simple installation once cut. All colors feature a gloss surface.

Three-ply black/white/black Stratocaster style back plate with 6 mounting holes.

Replacement pickguard for Fender® 1957 Strat® models. These single ply pickguards have eight mounting holes. Cut from a thicker single ply sheet, these pickguards offer a vintage style with added rigidity. Fits most American, Japanese, and Mexican '57 Stratocasters®.

Replacement jack plate for Telecasters

Jaguar style preset control plate in chrome. Perfect replacement for most Jaguar style guitars. 4.57” x 1.79” plate mounting center distance (0.14” diameter, recessed).

Replacement pickguard for Fender® American Deluxe Strat models. These pickguards have eleven mounting holes and feature cutouts for two single coil pickups and a humbucker in the bridge position. The humbucker cutout has rounded corners for a flush fit with uncovered pickups. Fits most American Deluxe Stratocasters® that are routed for a humbucker bridge pickup.
Features:

• 3-ply / 2.5mm thickness
• 11 mounting holes
• Shielding over electronics cavity
• Fits 3/8" bushing pots
• Various colors available