Hardware

Washer - Rubber, Chassis Mount, ⅞" Diameter
Gum rubber chassis mounting washers as used on thirties vintage Zenith and Philco radio. Allows proper dial centering in cabinet opening. Overall dimensions 0.875" dia. x .233" thick.
$0.75
Nut - Cliff, Hex, for ¼" white Jacks
Hex nut for white Cliff Jacks, threading: 7/16-20. Also used on the footswitch jack in some Marshall amps.
$0.91
Nut - Hex, for Carling switches, ~\frac{15}{32}~"
Hex nut for Carling switches, 15/32". Sold individually.
$0.40
Contact Pin - Nickel Plated Brass, Seamless, 0.566" Height
0.125" diameter nickel plated brass contact pin. Fits .062" and .093" boards. Height is .566" when mounted. In addition to turret board use, these pin connectors are often found on printed circuit boards. They are referred to as through hole terminal pins, header pins, or crimp contact pins.
$0.15
Washer - Rubber, Chassis Mount, 1-⅛" x ¼" Thick
Gum rubber chassis mounting washers as used on thirties vintage Zenith and Philco radio. 1/4 inner dia. Allows proper dial centering in cabinet opening. Overall dimensions 1 1/8" dia. x 1/4" thick.
$1.95
Header - Round Pin, 20 Position, Breakaway, 2.54mm Spacing
20 position male pin headers with a 2.54mm (0.1”) pitch. These headers use round pins that are smaller than the standard square type and are perfect for use with IC sockets, breadboards, and machine pin sockets. The breakaway construction makes fitting them to projects simple. Features:
  • Round Pin
  • 20 Position
  • 2.54mm Spacing
  • Breakaway
$1.30
Nut & Washer - Panel, for Fender / Marshall Jacks
Package of 5
M12 x1.0 threading. Nut and washer set for panel-mounting jacks.
$1.55
Screw - 10-32, Phillips, Pan Head, Machine, Zinc, fine thread
Package of 5
Phillips panhead machine screw, 10-32, zinc. Phillips panhead machine screw, 4-40, zinc. Designed to go through a hole or nut that is pre-tapped to form a mating thread for the screw. Has a general purpose bearing area and can be substituted in most applications for round, truss, or binding heads. Phillips drive is the most common drive used and is designed to "camout" when the screw reaches optimum tightness, thus preventing damage to the screw head.
Starting at $1.05
Washer - Flat, M3, Nylon, for Front Panels
Package of 10
Colors Available:
High quality nylon M3 flat washers. These durable washers fit perfectly on M3 threaded screws. The small outside diameter provides a clean look beneath the head of the screw. These are great mounting washers for preventing rack rash on front panels like Eurorack synths or any other use where the surface beneath the screw requires protection.
$0.99
Washer - Flat, M12, Stainless Steel, Oversized
Colors Available:
Oversized M12 flat washers. These washers fit both metric (M12) and imperial (15/32) bushings for compatibility with the vast majority of foot switches and full-sized toggle switches. These oversized washers are a great way to add a distinctive look to projects.
Starting at $0.95
Nut - Switchcraft, Knurl Nut for Switches
Original Switchcraft Copper Alloy Knurled Locknut (Nickel Plated) Outside Diameter:5/8" Inside diameter threading:15/32" Width: 3/32"
$1.79
Finishing Washer - #4, Countersunk
Package of 10
#4 finishing washers. Designed for accommodating the heads of countersunk screws. It provides additional bearing area on the material being fastened and can be used to give a neat, finished appearance.
Starting at $1.35
Washer - ⅞" x ⅛" Thick, Rubber, Chassis Mount,
Gum rubber chassis mounting washers as used on thirties vintage Zenith and Philco radio. 1/4 inner dia. Allows proper dial centering in cabinet opening. Adhesive backing for lamenating to other washers to increase thickness. Overall dimensions 7/8" dia. x 1/8" thick.
$0.65
Screw - #8, Phillips, Pan Head, Self-Tapping, Zinc
Package of 5
Self tapping Phillips panhead machine screw #8, zinc type AB. Type AB screws tap their own mating internal thread. They require a preformed hole for installation into metallic materials but not necessary for wood or plastic materials. Combines locating point of Type A with thread size and pitch of Type B. Normal limitations of Type B apply. Has a general purpose bearing area and can be substituted in most applications for round, truss, or binding heads. Provides good control in driving and is the most recommended drive.
Starting at $0.72
Nut - Cage, Zinc, 8-32, Electroplate Panel Range .064-.105
Common replacement for many applications. The nut is free floating and will help to take care of problems with misaligned holes. Convenient cage design stops the nut from moving while tightening.
  • 8-32 Threading
  • Panel Range .064-.105
  • Zinc Finish
$0.75
Screw - M3, Phillips, Pan Head, Machine
Package of 5
Phillips panhead machine screw, M3 metric, zinc. Designed to go through a hole or nut that is pre-tapped to form a mating thread for the screw. Phillips drive is the most common drive used and is designed to "camout" when the screw reaches optimum tightness, thus preventing damage to the screw head.
See S-HS-M3-6-X for colored 6mm M3 screws.
Starting at $0.75
Nut - M8x0.75 hex, for potentiometers / switches / jacks
Package of 5
M8 x 0.75 threaded hex nut. For use on potentiometers, switches, and jacks.
$1.25
Nut - Large Dress Nut, Carling, 15/32-32UNS, Plastic
Colors Available:
Genuine Carling Technologies dress nuts for use with full size toggle switches and footswitches. These nuts are made of a strong durable plastic and feature a chamfered edge with a knurled bottom half for a unique look that is simple to tighten down. The top of the threading is not capped so they can thread past the top of the bushing. These fit any 15/32-32UNS bushing but can also work with M12 bushings.
Starting at $0.68
Paper Label Tag - Pre-strung, Manilla, 2.75” x 1.375”
Package of 10
High quality manila paper tags. These tags are pre-strung with a soft string gentle enough to use on the most delicate equipment. The paper is heavy duty 13 point stock and the ¼” eyelet is reinforced to resist tearing. These are great tags for pricing, labeling, and cataloging equipment.
$1.95
Screw - #6, ⅜", Self-Tapping, Phillips Pan Head, Zinc
Package of 5
#6 x 3/8 zinc type AB. Type AB screws tap their own mating internal thread. They require a preformed hole for installation into metallic materials but necessary for wood or plastic materials. Combines locating point of Type A with thread size and pitch of Type B. Normal limitations of Type B apply. Has a general purpose bearing area and can be substituted in most applications for round, truss, or binding heads. Provides good control in driving and is the most recommended drive.
$0.50
Screws - Original Fender, Vintage Style Strat Bridge Mounting
Package of 12
Genuine Fender® vintage-style Strat bridge mounting screws. Some of Fender’s most requested replacement screws. Made for Fender® and used on a variety of vintage and contemporary models.
  • Set of 12 replacement screws
  • Genuine vintage specifications
  • Nickel plating
  • Phillips oval-head (#6 x 1 1/8")
  • Used on American Vintage Stratocaster® guitars
$3.25
Nut - Cage, Zinc, 10-24, Electroplate Panel Range .064-.105
Common replacement for many applications. The nut is free floating and will help to take care of problems with misaligned holes. Convenient cage design stops the nut from moving while tightening.
  • 10-24 Threading
  • Panel Range .064-.105
  • Zinc Finish
  • Sold Individually
$0.95
Finishing Washer - #10, Stainless Steel, Countersunk
Package of 10
#10 steel finishing washers. Designed for accommodating the heads of countersunk screws. It provides additional bearing area on the material being fastened and can be used to give a neat, finished appearance. Made of 18-8 stainless steel.
$1.35
Washer - Flat, M12, Nylon, for Foot Switches
Package of 10
Colors Available:
Nylon flat washers for use with foot switches. These washers are M12 size and fit both metric (M12) and imperial (15/32) bushings for compatibility with the vast majority of foot switches.
$2.50