Hardware

The Gotoh TLB-1 is a high quality set of guitar string ferrules. These press fit ferrules are a great choice for Telecaster® guitars or any guitar with a string through bridge. Includes six ferrules.

Stainless steel pan head Phillips self-tapping screws. #6 X ¾" length. Good for use with #'s 3,4 and 5.

Lock washer for Fender® potentiometers. Package of 12.

Original Fender 6-32 screws for use on pickups and switches.

Hex nut for Fender® potentiometers. Package of 12.

Set of hex set screws used for saddle-height adjustment on American Vintage series Stratocaster and Telecaster bridges.

• Set of 12 hex set screws
• For American Vintage Stratocaster and Telecaster guitars
• Comes with four 4-40 x 3/8" hex screws and eight 4-40 x 5/16" hex screws.

4 x 1.25, package of 12. For a variety of vintage and contemporary Precision and Jazz Bass models

Set screws for knobs. Package of 24. Fits: U.S. Telecaster / P-Bass chrome knobs and vintage-style knobs. Fender part number: 099-4922-000

Hex nuts for Rean jacks. Package of 12 Genuine Fender replacement jack nuts: 7/16-20 x 1/8 nickel-plated Used with many Fender amplifier jacks

Flanged finishing washers made of nickel plated brass. Designed for accommodating the heads of countersunk screws. These washers provide additional bearing area on the material being fastened and can be used to give a neat, finished appearance. This design closely resembles the flanged finishing washers found on later blackface and silverface Fender® amplifier cabinets. The #6 size is used for back panels on combo amps and heads. The #8 is used for extension cabinet back panels. For the earlier flush style finishing washers used on these amps, see S-HXFW-1N.

Genuine Gretsch® screws for mounting Gretsch pickup rings to the guitar's body. These chrome oval-head wood screws come in a pack of 12.
Accessory to P-PUGRETMR-S

Full set of replacement washers for Grover tuners. These are the washers that are between the arm of the tuner and the tuner’s knob. All three washers are used on a single tuner. Includes 6 nylon washers, 6 spring washers, and 6 flat washers.

Mounting bracket for vintage fuzz PCBs. This bracket is an exact replica of the bracket found in the Italian made Vox Tone Bender V828 pedals. The mounting width for the board is 1.35” which fits the P-PC-FUZZ-JEN, P-PC-BEND-MKII-BRN, and any other vintage spacing (0.15”) stripboard. The PCB mounting holes are threaded for M3 screws (sold separately). The two potentiometer holes are spaced 1.95” center to center and fit potentiometers with ⅜” bushings or smaller.

Vulcanized Cellulose Fiber for all electrical insulation. Gray insulating paper. .010" thick. used in switches, under terminals, in transformers, etc .where mechanical strength is required. Its qualities of toughness, flexibility, and edge-tearing resistance combined with high dielectric strength and ready absorption of insulating varnish have led to its predominant use as an improved motor slot call insulation. Dielectric strength 3000 volts. 10" wide roll contains 240 sq. inches.

Black 6-32 self-tapping screw from Hammond with a ¼” thread length. These screws pair perfectly with their black powder coated sheet metal chassis boxes.

6 pieces per set.

Pre-slotted black bone nuts for Stratocaster®, Telecaster®, and other Fender® necks with a 7.25” radius. A 7.25” fingerboard radius originated in the early 1950s and was used for most Fender® electric instruments until the 1980s.

• Height - 5.4 mm
• Width - 42.86 mm
• Thickness - 3.3 mm
• Radius - 7.25 in.

For a version of this nut with a 9.5” radius, see P-GTNN21.

Pre-slotted black bone nuts for Gibson necks with a 12” radius. A 12” fingerboard is the common radius used on most Gibson guitars. The bone used for the pre-shaped and pre-slotted nuts is dyed black using a process that results in a fully black nut.

• Height - 9.3 mm
• Width - 43.4 mm
• Thickness - 4.8 mm
• Radius - 12 in.

Pre-slotted black bone nuts for Stratocaster®, Telecaster®, and other Fender® necks with a 9.5” radius. A 9.5” fingerboard has been the standard Fender® neck radius since the 1980s. The bone used for the pre-shaped and pre-slotted nuts is dyed black using a process that results in a fully black nut.

• Height - 5.4 mm
• Width - 42.86 mm
• Thickness - 3.3 mm
• Radius - 9.5 in.

For a version of this nut with a 7.25” radius, see P-GTNN20.

Pick guard screws, phillips, ovalhead. Great for mounting countersunk pickguards, control plates, etc.

• 7/16” threaded portion
• Available in Black, Gold, Nickel, and Chrome plating
• Package of 100

Fender® replacement string ferrules for American Series and Mexican Stratocaster® and Telecaster®.

Fender® replacement string ferrules for Original Tele (6 ferrules)

Original Fender speaker mounting stud/nut set. These speaker mounting studs were used on countless amps of the '50s, '60s, '70s, and beyond. The reverse thread section screws into the baffle wood and the machine screw section holds the speaker in place using the included keps nuts.

• Used on early ’50s and ’60s vintage amplifiers
• Fits most vintage and modern amplifiers
• 1” of 8-32 machine head thread
• ¼” of reverse wood thread
• 1-½” overall length
• 8-32 keps nuts included

Fender part number: 099-2094-000

Silver rivets for fastening amplifier corners. For use on all Marshalls.