Hardware

Button bumpers help reduce unwanted vibrations on your equipment. (Package of 4). Overall Height = 5/8” Flange OD = 7/16” Flange Height = 5/16” Button OD = 5/16” Grommet Width = 3/64” Grommet Diameter = 1/4”

Clip nut for 8/32" thread. For use with machine screws

Ferrule for internal thread jacks, chrome (3/8-20).

Fender® replacement string ferrules for American Series Strat® and Tele®.

Fender® replacement string ferrules for Original Tele (6 ferrules)

The Gotoh TLB-1 is a high quality set of guitar string ferrules. These press fit ferrules are a great choice for Telecaster® guitars or any guitar with a string through bridge. Includes six ferrules.

6 pieces per set.

Nickel-plated steel finishing washers. Designed for accommodating the heads of countersunk screws. It provides additional bearing area on the material being fastened and can be used to give a neat, finished appearance. These high quality washers closely resemble the washers found on many vintage blackface and silverface amplifiers. Fits with #8 countersunk screws.

Genuine Bigsby® replacement handle stud.

Screw - Machine, Phillips Flat Head, 10-32 x 1 in., Stainless, package of 5
Nut - T-Nut, Zinc, 10-32, package of 5
Hardware only. Amp handle not included.

Black extruded heatsink with radial fins for use with TO-220 and TO-202 transistor packages.

These super sturdy fasteners are great for speaker covers or helping prevent earthquake damage. 4 sets of 2 clips (package of 8).

Vulcanized Cellulose Fiber for all electrical insulation. Gray insulating paper. .010" thick. used in switches, under terminals, in transformers, etc .where mechanical strength is required. Its qualities of toughness, flexibility, and edge-tearing resistance combined with high dielectric strength and ready absorption of insulating varnish have led to its predominant use as an improved motor slot call insulation. Dielectric strength 3000 volts. 10" wide roll contains 240 sq. inches.

Flat washer/locking ring. Fits switches that mount to 1/2" chassis holes. A 0.110" length guide tab ensures a locking fit (locking hole is 0.376" from chassis hole center).

Replacement nut for Marshall style pots with 7mm bushing. Sold individually

Replacement nut and washer for pots with a ⅜" bushing diameter.

M12 x1.0 threading. Nut and washer set for panel-mounting jacks.

Replacement nut and washer for pots and jacks that feature a ⅜" bushing with 3/8-32 threading. Sold in packs containing 100 nuts and 100 washers.

Nut - Keps with external tooth, Zinc, fits screws for chassis straps, 8-32 X 3 1/4, package of 10. Popular low-cost lock nut for commercial and industrial applications. Locking action is achieved when the nut is tightened against a bearing surface as the teeth of the lock washer dig into it.

Common replacement for many applications. The nut is free floating and will help to take care of problems with misaligned holes. Convenient cage design stops the nut from moving while tightening.

• 10-24 Threading
• Panel Range .064-.105
• Zinc Finish
• Sold Individually

Common replacement for many applications. The nut is free floating and will help to take care of problems with misaligned holes. Convenient cage design stops the nut from moving while tightening.

• 10-32 Threading
• Panel Range .064-.105
• Zinc Finish
• Sold Individually

Common replacement for many applications. The nut is free floating and will help to take care of problems with misaligned holes. Convenient cage design stops the nut from moving while tightening.

• 8-32 Threading
• Panel Range .064-.105
• Zinc Finish

Hex nut for white Cliff Jacks, threading: 7/16-20

Nut - Hex, for Cliff UK Jacks S-H902, S-H903, S-H904, & S-H905