Jacks & Plugs

Mono or stereo jack plate for back of cabinets.

Switchable stereo/mono jack plate for back of cabinets.

The Plug and Play eliminates the confusing switch found on most stereo cabinets. Just pick your impedance and plug in. Label is set at the common 4/16 Ohm Mono and 8 Ohm Stereo. Ready to install with a steel dish, wires, and speaker connectors.

High quality acoustic end pin style jacks from Switchcraft. These nickel plated jacks have three conductors, a strain relief clamp, and a threaded shroud for a professional looking wiring job. The special strap nut can be removed to reveal a hex nut that can be used for external tightening of the jack.

High quality vintage-design ¼” plug from Switchcraft. This TS (mono) plug features an all metal handle (for .29 to .30 inch cable diameter), cable clamp and a heavy copper alloy-plated flex relief spring (for .265 inch cable diameter maximum).

XLR 3 pole male to 3 pole male adapter, pre-wired, metal shell. Nickel. Features:

• Adapter pre-wired for convenience
• 120 ohm terminators

Pure Tone’s new long threaded three pole (stereo) 1/4" jack provides full contact for improved connections and signal integrity. This jack locks the cable securely into place creating a greater surface area connection to carry more signal for an improved frequency stability. This jack is a great choice for both mono and stereo applications as well as guitars using active electronics.

C Series Circular Panel Mount 3 Pin XLR Female, mounts with #5 Screws (Not included) - Silver Pins / Nickel Finish.

Type 152B. ¼" Female Stereo Input Jack 3-conductor. Thick panel-mount jack with cable clamp. Brass finish.

The Amphenol T series SwitchPlug™ uses a unique 360 degree precision sliding helical spring contact design to quietly and accurately switch the signal circuit safely to ground during instrument changes under load, thereby avoiding annoying thumps, pops and squeals.

Switchcraft Type 13E phono jack. Mono 2-conductor isolated break circuit. Mates with standard ¼" plugs and is available with 0.25" inside diameter bushing. Includes nut and washer.

1/4" Mono 2 Conductor Jack, Transfer Circuit. Used in Fender, part number: 004-1701-000. Includes nut and washer.

4 pole cable connector, chuck type strain relief. Mates with W-SO-J41 The industry-standard for loudspeaker connections offer extremely reliable and robust cable connectors with a reliable locking system. They feature solid contacts with screw-type terminals including a stranded wire protection which offer also solder termination. Features:

• Current rating 40 A continuous, 50 A audio signal with 50% duty cycle
• Only 3 parts, easy to assemble
• High impact materials – long-lasting and reliable
• Easy and extremely precise locking system "Quick Lock"
• 1 piece strain relief, chuck for 6 to 10 mm cable O.D.
• Improved grip on latch

Switchcraft Type 188 Jumbo Plug. ¼" Mono 2 Conductor Heavy Duty Cable Mount Plug - Nickel Finish.

High quality made in USA ¼” plugs from Lava Cable. This right angle plug features an ultra low profile and a unique soldered connection that provides a quicker assembly than standard soldered connectors. The insulation system used in the plugs ensures a solid connection that is nearly impossible to short. Lava Soldered Right Angle Connectors are the smallest profile soldered plugs on the market today at only .405” in width and .515” in outer diameter. Soldering is easy with just one small solder point. Included insulators prevent shorting. To assemble:

• Strip 0.75” of the outside jacket from the end of the instrument cable.
• Feed the stripped end including the shield braid through the large black plastic insulator tube.

Fender style 1/4" straight mono (tip-sleeve) open plug. Perfect for use as "open" plug for Fender "Hot Rod" and "Blues Reissue" amps having both "Main Speaker" and "External Speaker" jacks allowing you to connect an alternate speaker impedance with the open plug inserted in the "Main Speaker" jack (speaker load configuration 3).

Made by G&H industries. High quality, oxygen-free copper core phone plugs. Made in America. For large wire, 8-12 gauge speaker cable.

Plastic jack cup for input jack on speaker cabinets.

• Diameter = 3 3/4''
• Center to Center Screw Hole Spacing Distance = 2 1/8''

Amphenol "T-Series (Pro Range)" Phone Plug. 1/4" Mono straight plug with large Jaws cable clamp, metal backshell and black finish. Internal cable clamp fits cable outer diameters ranging from 0.236” to 0.295” (6 mm to 7.5 mm).

Original replacement for Fender® amps. ¼" Stereo Input Jack that has 9 PCB mount terminals.

1/4" professional right-angle phone plug, nickel contacts, nickel shell The heavy duty professional phone plug series improves on the design of the existing C series by offering the thinnest available A-gauge 1/4" plug with unique Neutrik chuck type strain relief on the market. The slimline shell with a width of 14.5 mm meets the most recent requirements for highest density jackfields (15.88mm jack pitch). The precise machined one-piece tip contact without rivets makes it unique and avoids hook up in a socket or break off the tip. The Plug X Series serves all applications such as guitar applications, audio cables, snakes, speakers, amplifiers and mixing desks.

2-pole 1/4" professional right-angle phone plug, gold contacts, black shell. Large jaw cable clamp for use with cable with an outer diameter of 5.5mm to 6.5mm.

Switchcraft 285L ¼” plug for large cables. The 285L features the same spec’s and build quality as the Switchcraft 280 but features a larger cable clamp and a .375" rear hole in the handle. These are great plugs for thicker wires such as speaker cables. Specifications:

• Sleeve, Tip and Body: Nickel-plated copper alloy
• Terminals: Solder lug - Tinned copper alloy
• Handles: Shielded - machined Nickel-plated copper alloy
• Tubular insulator inside handle

Switchcraft ¼" Mono 2-Conductor Input Jack, Isolated Make Circuit (Type 13). Includes nut and washer