Pedals & Kits
Are you a DIY'er and enjoy building your own gear? Our kits range from beginner to advanced skills, so there is something for everyone!
Pedal Kit - Mod® Electronics, Thunderdrive Deluxe, Overdrive
Adjusting volume control and gain controls provides a wide variety of tones in spite of its simple construction. The Turbo switch provides an additional boost in volume and less internally generated distortion. It is capable of overdriving the preamp section of your guitar amp or adding its own layer of distortion at lower volume. The current draw of this pedal is very low at 1.3 milliamps, allowing for long battery life.
$44.59
Pedal Kit - Mod® Electronics, The Piledriver, Power Boost
The Mod® Electronics Piledriver is a clean-boost kit that will provide up to 38dB of gain to your guitar signal. Use it to push your preamp into overdrive or as a line driver if you are experiencing signal degradation from your effects chain. This is a simple kit and great for beginners!
$35.35
Parts Kit - Supa Fuzz Pedal, PCB Version, Premium Build
PCB and parts kit for the Supa Fuzz. This is based on the classic PCB version produced by Marshall. This kit includes all of the resistors and capacitors used on the included circuit board. The germanium PNP transistors are not included such that customers can select and test their own.
$40.39
Radio Kit - 2 Tube Regenerative Radio
This radio kit will cover the AM radio band along with the SW radio band. Power for this receiver is 1.5 V DC for the filaments and 45V DC for the plate current. A D cell and five 9V transistor batteries wired in series will work to power this radio. A 2000 ohm headset or an audio amplifier is required. Requires two T-1T4_DF91 tubes (not included).
$54.95
Pedal Kit - Mod® Electronics, Step Ladder, Input Attenuator
The Mod® Electronics Step Ladder is a passive input attenuator using high quality components for excellent reliability. True-bypass mode provides the maximum signal level. The attenuator pot and two toggle switches allow for flexibility in the amount of signal attenuation when not in bypass mode. Treble bleed capacitors in the circuit retain crisp high frequencies even at maximum attenuation. The Step Ladder is ideal for anything from getting a slight boost while playing single-note acoustic guitar leads or for jumping from clean to overdrive in a high-gain electric guitar amp.
$49.95
Parts Kit - MKII Fuzz Pedal, Stripboard Professional Version, Premium Build
PCB and parts kit for the MKII fuzz pedal. This is based on the classic stripboard Tone Bender Professional. This stipboard fuzz circuit was also used in some versions of the Supa Fuzz as well as some other fuzz pedals. This kit includes all of the resistors, capacitors used on the included circuit board. The germanium PNP transistors are not included such that customers can select and test their own.
$49.39
Parts Kit - V828 Italian Fuzz Pedal, PCB Version, Premium Build
PCB and parts kit for the V828 fuzz pedal. This is based on the classic Italian-made V828 Tone Bender. These were also sold under the Jen brand. This kit includes all of the resistors, capacitors, and solder tags used on the included circuit board. The germanium PNP transistors are not included such that customers can select and test their own.
$44.89
Effects Kit - Mod® Electronics, The Wave, Spring Reverb
The Mod® Electronics Wave is a versatile stand-alone, tube driven analog spring reverb unit kit. It can be used in front of your guitar amp or as a line-level analog reverb effect for the recording studio. Two controls allow you to serve up a wide range of wetness from just a touch to over the top psychedelia. The Dwell control adjusts the input signal level driving the tank and the Reverb control adjusts the level of output reverberations from the tank. The Wave's all tube design utilizes four dual triode vacuum tubes - three 12AX7s and one 12AT7 - and comes with a MOD® three-spring reverb tank. MOD® reverb tanks are deemed the closest to the original reverb tanks from the '60s made today. The Wave's reverb function can be switched in and out pop-free via the front panel toggle or with a footswitch. Footswitch sold separately (see P-H470 for compatible footswitch).
$360.00
Effects Pedal - Maxon, GE601, Graphic Equalizer
The Maxon GE601 graphic equalizer is the perfect tool for dialing in guitar tone. The six bands are set with slide potentiometers offering precision controls with a visual representation of the sound spectrum. Each band can both cut and boost sound for a variety of tonal shaping effects as well as frequency specific boost effects.
Features
Features
- Six-band graphic eq with an overall level volume capable of producing various sounds
- Bands cover 100Hz to 3.2KHz for effective tone shaping with guitars
- Each band can cut or boost providing a variety of uses
- LED indicator for effect on/off
- DC power or 9V battery
- Made in Japan
$120.95
Pedal Kit - Mod® Electronics, The Trill
The Mod® Electronics Trill tremolo pedal offers classic tremolo tones in an easy to build kit. The Trill's speed knob provides a wide range from a very slow to rapid fire effect. The depth knob varies the ratio between effected and dry signal. Using modern, low noise transistors makes operation of The Trill quiet with no signal drop when engaged. The Trill uses true bypass foot switching so it is out of the signal path when not engaged. All you need to provide is solder and tools! Uses 9 volt battery which is not included.
$46.95
Pedal Kit - Mod® Electronics, Erratic Clutch Deluxe
The Mod® Electronics Erratic Clutch Deluxe is a unique effect pedal kit that gives you fuzzy square wave distortion as well as a monophonic sub-octave square wave using a total of only four transistors. The two signals can be used individually or mixed together for a raw and sonically rich synthy output. Full of character and quirk, this pedal will give you a truly original sound. The middle knob is the bias control. This adjusts the pulse width in the initial fuzz stage of the pedal. Set this knob to fit your pickups and playing style. The closer to the center the longer the note will sustain but with that comes more chaotic tracking for the divider. Moving it more clockwise or counterclockwise will give you more predictable note tracking on the divider with less sustain.
$72.95
Guitar Wiring Upgrade Kit - Mod® Electronics, Short Bushing Potentiometer Les Paul
The K-GMOD-3S is a vintage style wiring kit for Les Paul guitars. This version comes with short bushing pots for flat top Les Paul’s. Use this kit to upgrade your current Les Paul electronics to high quality parts. This kit also includes a treble bleed mod for the volume pots to enhance clarity with lower settings and comes with detailed instructions and all the parts you need to make your modification.
$36.90
Snubber Kit - eliminate fuzz from amplifier
Snubber parts kit for circuits. Used to build a "snubber circuit" to remove unwanted high frequencies and high voltages resulting from output transformer ringing in a guitar amplifier, without the "brick wall" effect of using diodes.
Starting at $8.25
Parts Kit - Zonk Machine, PCB Version, Premium Build
PCB and parts kit for the Zonk Machine. This is based on the original PCB version. This kit includes all of the resistors and capacitors used on the included circuit board. The germanium PNP transistors are not included such that customers can select and test their own.
$45.05
Pedal Kit - Mod® Electronics, Suspended Chime, Chorus, Delay
The Mod® Electronics Suspended Chime has two powerful effects in one pedal - chorus and chorus/delay. The Suspended Chime features a blend knob which allows you to go from subtle to lush chorus effect in either set up. Using the toggle switch, you can add a 190 millisecond delay to the chorus introducing special depth to your tone. Varying the dry/wet mix can fatten your rhythms or produce a shimmering 12-string sound. The Suspended Chime kit comes equipped with an LED indicator and industry standard 9 volt center negative power jack. MOD® Kits are designed to give both novice and experienced musicians the opportunity to build their own amps and effects pedals. All kits come with easy to follow instructions and use point to point wiring. Pre-drilled enclosure and all parts are included. All you need to provide are hand tools, a soldering iron and solder. All effects pedals operate on a 9V battery.
$99.95
Pedal Kit - Mod® Electronics, The Saturator
The Mod® Electronics Saturator is an overdrive pedal kit that can cover a wide range of gain effects, transitioning smoothly from a massive clean boost to a warm and saturated distortion with the turn of a knob. The saturation is controlled with the Soak knob, which dials in the amount of symmetrical soft-clipping applied to the guitar signal. When fully counterclockwise, the signal is unaffected and clean. Rotating the knob clockwise will incrementally increase the soft-clipping, morphing from a clean signal through subtle-to-heavy saturated overdrive sounds and straight into distortion territory. The Level knob sets the overall volume of the clean or saturated output. Unity gain is at roughly 8 o'clock. With the Soak set to clean, rotating the Level knob clockwise will increase the level to upwards of 30dB.
$47.95
Parts Kit - Iss 1 Fuzz Pedal, Standard Version, Premium Build
PCB and parts kit for the Iss 1 fuzz built in the style of the standard germanium Fuzz Face. This kit includes all of the resistors, capacitors, and transistors used on the included circuit board. The germanium PNP transistors are not included such that customers can select and test their own.
$42.26
Pedal Kit - Mod® Electronics, The Ring In Return, Octave-Up Fuzz
The Ring In Return is an octave-up fuzz effect that is an all-analog design that captures those late 60s octave-up fuzz tones. Transformer-coupled germanium diodes produce sounds that range from a subtle octave-up to thick, harmonically-rich sonic textures and synth-like tones. Experimenting with different pickups and tone-control settings on your guitar with The Ring In Return can also produce sitar-like sounds. Warning: This circuit was designed for use with a 9 VDC power supply only.
$69.95
Guitar Wiring Upgrade Kit - Mod® Electronics, 3 Position PRS Style
The K-GMOD-4 is a vintage style wiring kit for PRS guitars. Use this kit to upgrade your current PRS electronics to high quality parts. This kit also includes a treble bleed mod for the volume pot to enhance clarity with lower settings and comes with detailed instructions and all the parts you need to make your modification.
$44.26
Parts Kit - Eyelet-Rite Fuzz Pedal, Germanium Version, Premium Build
Parts Kit - Eyelet-Rite Fuzz Pedal, Germanium Version, Premium Build PCB and parts kit for the Eyelet-Rite fuzz pedal. This is based on the point to point version of the germanium Mosrite Fuzzrite pedal. This kit includes all of the resistors, capacitors, eyelets, and the footswitch used on the included circuit board. The germanium PNP transistors are not included such that customers can select and test their own.
$53.86
Pedal Kit - Mod® Electronics, The Contortionist II, Fuzz
The Mod® Electronics Contortionist II kit is an all analog, high octane fuzz box. It produces fuzz with layered octave overtones similar to those produced by an electronic-bow. The frequency multiplier circuitry creates harmonics that swell and recede depending on gain setting, pick attack, neck position and pickup. This is a high gain circuit that can put out up to 2 volts and will provide ample amounts of sustain. The Contortionist II has all the features of the original Contortionist with an added tone control for a wider range of sounds, and an LED that lights up when the unit is activated.
$53.75
Guitar Wiring Upgrade Kit - Mod® Electronics, ES-335 Standard
The K-GMOD-6 is a vintage style wiring kit for ES-335 guitars. Use this kit to upgrade your current ES-335 electronics to high quality parts. This kit also includes a treble bleed mod for the volume pots to enhance clarity with lower settings and comes with detailed instructions and all the parts you need to make your modification.
$63.70
Kit - BusBoard, Junior Genius Blinky Lights Kit
Junior Genius Kits are built for experimentation, learning and fun! Experience the joy of seeing your first LED light up. The Blinky Lights Kit leads you through 10 core activities, from a simple LED circuit up to more advanced transistor LED blinky light circuits, using standard parts on a real-world breadboard. Learn about voltage and current by using LEDs, resistors, capacitors and transistors. You'll be able to build circuits using a schematic diagram, and there's plenty of help to get you there. Simple examples make it easy to grasp the basics and 'What's Happening' and 'Things To Try' sections encourage you to dig deeper. You will get valuable assembly and troubleshooting experience as you learn to use a great experimentation tool, the solderless breadboard. Real hands-on experience means greater educational value. This next-generation science kit doesn’t seal the parts into simplified plastic blocks.
$27.95
Effects Pedal - Maxon, PAC9, Pure Analog Chorus
The PAC9 is a classic analog chorus featuring swirling warm chorus sounds and stereo output for a wide chorus spread. In addition to the standard Speed and Width controls, the PAC9 offers a Bright switch for a focused sound and a Pure switch that boosts the signal. Features
- Clean analog chorus sound using the Maxon MC4107D BBD chip
- Speed and Width controls
- Bright and Pure switches offer a variety of sounds for bold and deep chorus effects
- Widely adjustable Speed range of 0.33Hz - 8Hz.
$229.95