You are here

Kits

Filter these results
Sort By:
products per page
View Mode: List View · Grid View
K-704Upgrade Kit - For Fender®, Mid Boost Preamp for Strats

This kit includes all of the parts needed to upgrade your guitar with the Mid Boost Pream used on the Buddy Guy and Eric Clapton Strats. Includes PCB ASSY Clapton preamp, Control 50K audio, Control 350K special taper, washer, jack output OPN stereo surge, TBX tone control and schematic wiring diagram.


$51.00
Click to read more about this product.
K-920Effects Pedal Kit - MOD® Kits, The Piledriver, Power Boost

"The PileDriver" is a clean boost kit that will provide up to 38dB of gain to your guitar signal. Use it to push your preamp into overdrive or as a line driver if you are experiencing signal degradation from your effects chain. This is a simple kit and great for beginners!


$24.95
Click to read more about this product.
K-MOD101Amp Kit - MOD® Kits, MOD101 guitar amplifier

MOD 101 Guitar Amp Kit Features:



  • All Tube Design (solid-state diodes used only for full-wave rectification)
  • 60W output power into 4, 8, 16 and 20 Ω
  • 1 channel with customizable: tone stack, power tubes, negative feedback, input miller capacitance volt divider/LP filter, and preamp cathode bypass cap (all parts included)
  • Vintage channel controls: bass, treble and volume
  • Vintage pilot lamp and screw-on jewel cover for power-on indication
  • DPDT power switch circuit for instant high-voltage drain in power-off
  • Standby Switch

$465.00
Click to read more about this product.
K-MOD102-PLUSAmp Kit - MOD® Kits, MOD102+ guitar amp

The MOD102+ expands on the same all analog vacuum tube classic American circuit design combined with a British style Class A output section as the Original MOD102 with some much added special “+” features. These special features include a three position progressive toggle switch for off-standby-power and additional push-pull functionality for each control - pull out the bass control knob for “mid boost”, pull out the treble control knob for “bright”, pull out the volume control knob for “turbo”.


$265.00
Click to read more about this product.
K-703Amp Mod Kit - MOD® Kits, Normal to Bass Conversion

This kit was designed for those who play both guitar and bass. Turn the Normal Channel in your silver-face or black-face Fender amp into the Bass Instrument channel. The kit comes with parts and easy to follow instructions. You will need your own tools and solder.


$16.95
Click to read more about this product.
K-930Effects Pedal Kit - MOD® Kits, The Persuader, Tube Drive
Build your own tube preamp pedal built around a 12AX7 tube. Go from clean, warm tone to smooth, real tube overdrive.
This kit includes pre-drilled die-cast aluminum enclosure and all parts with easy to follow instructions. All you need to provide is solder and soldering iron.
The Persuader allows for easy access to the tube, giving you the ability to quickly experiment with different tube brands and 12AX7 tube relatives.
Operates on a 9V battery or AC adapter, which is not included. When completed, this pedal draws considerable current and battery life will be short. The Godlyke 9-volt adapter (M-PAS-S) may be purchased separately to power your new pedal.
$64.95
Click to read more about this product.
K-925Radio Kit - 2 Tube Regenerative Radio
This radio kit will cover the AM radio band along with the SW radio band. Power for this receiver is 1.5 V DC for the filaments and 45V DC for the plate current. A D cell and five 9V transistor batteries wired in series will work to power this radio. A 2000 ohm headset or an audio amplifier is required.
Requires two T-1T4_DF91 tubes (not included).
$42.95
Click to read more about this product.
K-SNUB1Snubber Kit - for 2 EL84 Tubes
Snubber parts kit for circuits with (2) EL84 tubes
x2 RQ3K - 3K Ohms 5 Watt power resistor
x2 R-B8D2M - 8.2Meg Ohms 1 Watt resistor
x2 RD0047-600 - 0.0047uF 600 Volt Orange Drop Capacitor
Summary Written by Dave Zimmerman - Maven Peal Amplifiers
The "Snubber" circuit was published in the "Radiotron Designers Handbook" in the 1930s and is supposed to serve as a "[sonically transparent] shock absorber" to remove unwanted high frequencies and dangerously high voltages resulting from output transformer ringing, without the "brick wall" effect of using diodes.  "Output transformer ringing often so
$6.25
Click to read more about this product.
K-SNUB2Snubber Kit - for 4 EL84 Or 2 Octal Tubes
Snubber parts kit for circuits with (4) EL84 tubes or (2) Octal tubes
x2 R-Q1D5K - 1.5K Ohms 5 Watt power resistor
x2 R-B8D2M - 8.2Meg Ohms 1 Watt resistor
x2 C-RD01-600 - 0.01uF 600 Volt Orange Drop Capacitor
Summary Written by Dave Zimmerman - Maven Peal Amplifiers
The "Snubber" circuit was published in the "Radiotron Designers Handbook" in the 1930s and is supposed to serve as a "[sonically transparent] shock absorber" to remove unwanted high frequencies and dangerously high voltages resulting from output transformer ringing, without the "brick wall" effect of using diodes.  "Output transfo
$6.45
Click to read more about this product.
K-SNUB3Snubber Kit - for 4 Octal Tubes
Snubber parts kit for circuits with (4) Octal tubes
x2 R-R820 - 820 Ohms 10 Watt power resistor
x2 R-B8D2M - 8.2 Meg Ohms 1 Watt resistor
x2 C-RD022-600 - 0.022uF 600 Volt Orange Drop Capacitor
Summary Written by Dave Zimmerman - Maven Peal Amplifiers
The "Snubber" circuit was published in the "Radiotron Designers Handbook" in the 1930s and is supposed to serve as a "[sonically transparent] shock absorber" to remove unwanted high frequencies and dangerously high voltages resulting from output transformer ringing, without the "brick wall" effect of using diodes.  "Output transformer ringing oft
$7.30
Click to read more about this product.
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Kits