You are here

Kits

Filter these results
Sort By:
products per page
View Mode: List View · Grid View
K-MOD101Amp Kit - MOD® Kits, MOD101 guitar amplifier

MOD 101 Guitar Amp Kit Features:



  • All Tube Design (solid-state diodes used only for full-wave rectification)
  • 60W output power into 4, 8, 16 and 20 Ω
  • 1 channel with customizable: tone stack, power tubes, negative feedback, input miller capacitance volt divider/LP filter, and preamp cathode bypass cap (all parts included)
  • Vintage channel controls: bass, treble and volume
  • Vintage pilot lamp and screw-on jewel cover for power-on indication
  • DPDT power switch circuit for instant high-voltage drain in power-off
  • Standby Switch

$465.00
$418.50
You save: 10%
Click to read more about this product.
K-MOD102-FAmp Kit - MOD® Kits, MOD102 guitar amp (Non-US Version)

The MOD102-F is the foreign (non-USA) version of the MOD 102 including a Hammond 369EX world power transformer instead of the 269EX. Please note: there is no power cord included with this kit (due to variations in electrical outlets around the world). You will need to find a power cord that can fit through the 1/4" diameter (6.35 mm) rubber grommet hole on the rear panel.


$250.00
$225.00
You save: 10%
Click to read more about this product.
K-MOD102Amp Kit - MOD® Kits, MOD102 guitar amplifier

For the non-US version of the MOD 102, please see K-MOD102-F MOD 102 Guitar Amp Kit Features:



  • All Tube Design (solid-state diodes used only for full-wave rectification)
  • 5W output power into 8 Ohm
  • 1 channel
  • Vintage channel controls: bass, treble and volume
  • Vintage pilot lamp and screw-on jewel cover for power-on indication
  • Output Impedance: 8 Ohm
  • Tubes included: one 12AX7 (preamp), one EL84 (JJ Electronic brand)
  • Hammond Mfg 269EX power transformer and P-T31 single ended output transformer
  • Cathode biased class

$215.00
$193.50
You save: 10%
Click to read more about this product.
K-MOD102-PLUSAmp Kit - MOD® Kits, MOD102+ guitar amp

The MOD102+ expands on the same all analog vacuum tube classic American circuit design combined with a British style Class A output section as the Original MOD102 with some much added special “+” features. These special features include a three position progressive toggle switch for off-standby-power and additional push-pull functionality for each control - pull out the bass control knob for “mid boost”, pull out the treble control knob for “bright”, pull out the volume control knob for “turbo”.


$265.00
$238.50
You save: 10%
Click to read more about this product.
K-MOD103Effects Kit - MOD® Kits, The Wave, Spring Reverb

The Wave is a versatile stand-alone, tube driven analog spring reverb unit kit. It can be used in front of your guitar amp or as a line-level analog reverb effect for the recording studio. Two controls allow you to serve up a wide range of wetness from just a touch to over the top psychedelia. The "dwell" control adjusts the input signal level driving the tank and the "reverb" control adjusts the level of output reverberations from the tank. The Wave's all tube design utilizes four dual triode vacuum tubes - three 12AX7s and one 12AT7 - and comes with a MOD® three-spring reverb tank.


$275.00
$247.50
You save: 10%
Click to read more about this product.
P-18WLiteIIB 18W Kit - Scratch Build Parts
GuitarAmplifierPCBs.com
18 Watt LiteIIb "Baby Will"
Parts List for Scratch Build - Contains the following items:
Two C-ET47-50: Electrolytic Capacitor - 47uF 50V
One C-MD1-630: Mallory 150 Capacitor - 0.1uF 630V
One C-MD0047-630: Mallory 150 Capacitor - 0.0047uF 630V
Four C-MD01-630: Mallory 150 Capacitor - 0.01uF 630V
One C-SM500: Silver Mica Capacitor - 500pF 500V
One R-R150: Wire Wound Resistor - 150 ohm 10 watt
Two R-VA500KA: Potentiometer - 500K audio 24 mm
Two S-H901: Jack - ¼" Panel Mount
Eight P-K339: Knobs - Marshall Style
Four P-ST9-620: Tube Socket - 9 pin PC Mount
Two S-H144: Tube
$49.35
$44.42
You save: 10%
Click to read more about this product.
Subscribe to RSS - Kits