Pedals & Kits

PCB and parts kit for the Iss 1 fuzz built in the style of the standard germanium Fuzz Face. This kit includes all of the resistors, capacitors, and transistors used on the included circuit board. The germanium PNP transistors are not included such that customers can select and test their own.

PCB and parts kit for the MKII fuzz pedal. This is based on the classic stripboard Tone Bender Professional. This stipboard fuzz circuit was also used in some versions of the Supa Fuzz as well as some other fuzz pedals. This kit includes all of the resistors, capacitors used on the included circuit board. The germanium PNP transistors are not included such that customers can select and test their own.

PCB and parts kit for the V828 fuzz pedal. This is based on the classic Italian-made V828 Tone Bender. These were also sold under the Jen brand. This kit includes all of the resistors, capacitors, and solder tags used on the included circuit board. The germanium PNP transistors are not included such that customers can select and test their own.

The Mod® Electronics Penetrator is a treble boost pedal kit with enough gain to cut straight through any mix. This pedal adds glistening harmonics that get loud enough to saturate your amp’s front end. Adjust the level knob to vary the output so there’s no mistaking when you kick this pedal in. Great for solos or when you need your guitar front and center.

GuitarAmplifierPCBs.com 18 Watt LiteIIb "Baby Will" Parts List for Scratch Build The Baby Will is a PCB simplified version of the legendary Marshall 18 Watt 1974x circuit. The circuit we laid out on a circuit board is known as the LiteIIb. It's capable of tone from clean jazz, crunchy blues, to raunchy classic rock. Crank up the volume and you'll be in AC/DC Back In Black heaven. The magic of the LiteIIb is its simplicity.

The OOD9 is the updated version of the original Maxon overdrive pedal, the OD880. This overdrive is equipped with NJM4558D op amps for a warm and low-noise overdrive that pairs perfectly with tube amplifiers and other distortion pedals. The OOD9 offers a dynamic response that preserves the tone of the input providing a smooth and clear overdriven sound.

The Mod® Electronics Saturator is an overdrive pedal kit that can cover a wide range of gain effects, transitioning smoothly from a massive clean boost to a warm and saturated distortion with the turn of a knob. The saturation is controlled with the Soak knob, which dials in the amount of symmetrical soft-clipping applied to the guitar signal. When fully counterclockwise, the signal is unaffected and clean. Rotating the knob clockwise will incrementally increase the soft-clipping, morphing from a clean signal through subtle-to-heavy saturated overdrive sounds and straight into distortion territory. The Level knob sets the overall volume of the clean or saturated output. Unity gain is at roughly 8 o'clock. With the Soak set to clean, rotating the Level knob clockwise will increase the level to upwards of 30dB.

A T-Filter Pedal Kit - the Mod® Electronics Tea Philter pedal produces a fixed wah tone allowing you to lock it in without rocking the pedal back and forth. Every guitar/wah combination has a certain sweet spot that is perfect for lead and chord work. The Tea Philter lets you dial in everything from your favorite vocal mid-range tone to thick lows. Using point-to-point wiring and easy-to-follow instructions you can have a working fixed wah pedal in a matter of hours. The effect pedal operates on a 9V battery. For a longer lasting option, a 9-volt adapter can be purchased separately.

The Seismic / Shift is a JFET boost based on one of the earliest effects to ever be used on stage. This pedal adds subtle color to a guitar's sound while maintaining the natural tone of the guitar. It packs a serious punch that can cut through any mix when soloing or whenever some extra “umph” is required. The Seismic Shift pairs nicely with amps and other pedals. Place it ahead of tubes, preamps, overdrives, distortions, and fuzz pedals to shift your gear onto a new level. The Seismic Shift pedal kit is the introduction to the Nexus Series from Mod Electronics. This series features a PCB base rather than the Mod Electronics’ traditional point-to-point wiring kits to offer builders an even wider variety of effects to build. The Seismic Shift kit is designed for all skill sets and is the perfect first build for those unfamiliar with PCB construction. The pedal operates on both 9VDC and 18VDC.

The K-GMOD-2 is a vintage style wiring kit for Stratocaster guitars. Use this kit to upgrade your current Strat electronics to high quality parts. This kit also includes a treble bleed mod for the volume pot to enhance clarity with lower settings and comes with detailed instructions and all the parts you need to make your modification.

The Mod® Electronics Persuader Deluxe utilizes a Darlington preamp to push cascaded triode vacuum tubes into distortion. A boost switch provides an additional layer of flexibility with added gain and a little extra bottom end. An LED indicator lights up when the Persuader Deluxe is engaged and not in true bypass mode. Operates on a 9V battery or AC adapter, which is not included. When completed, this pedal draws considerable current and battery life will be short. The Godlyke 9-volt adapter (M-PAS-S) may be purchased separately to power your new pedal.

The Phase / Off is a four-stage phaser based around the Sound Semiconductor SSI2140 voltage-controlled multi-mode filter. This pedal offers classic phasing effects along with plenty of control to dial in the perfect amount of modulation using the Depth, Rate, and Regen knobs. The Stages switch can change the Phase / Off from four-stage phaser to a two-stage phaser providing a wide variety of different phasing sounds. Change the Mode switch from LFO to Manual to use the Phase / Off in fixed phase mode controlled by the Depth knob for unique filtering effects. The Phase / Off pedal kit is the second entry in the Nexus Series from Mod® Electronics. This series features a PCB base rather than the Mod® Electronics’ traditional point-to-point wiring kits to offer builders an even wider variety of effects to build. The Phase / Off is a great pedal for intermediate skill sets. It features an all through-hole build with pre-soldered SMT SSI2140. The pedal operates on 9VDC.

Genuine Fender® Mid Boost upgrade kit for Strats with active electronics. This circuit is used in the signature Eric Clapton and Buddy Guy strats and is commonly referred to as the Clapton Boost. The Mid Boost knob adjusts gain from 0 dB (no boost) to 25 dB (maximum boosted mids). This boost sounds great clean and adds powerful control to distortion.

The K-GMOD-3S is a vintage style wiring kit for Les Paul guitars. This version comes with short bushing pots for flat top Les Paul’s. Use this kit to upgrade your current Les Paul electronics to high quality parts. This kit also includes a treble bleed mod for the volume pots to enhance clarity with lower settings and comes with detailed instructions and all the parts you need to make your modification.

The Mod® Electronics Contortionist II kit is an all analog, high octane fuzz box. It produces fuzz with layered octave overtones similar to those produced by an electronic-bow. The frequency multiplier circuitry creates harmonics that swell and recede depending on gain setting, pick attack, neck position and pickup. This is a high gain circuit that can put out up to 2 volts and will provide ample amounts of sustain. The Contortionist II has all the features of the original Contortionist with an added tone control for a wider range of sounds, and an LED that lights up when the unit is activated.

PCB and parts kit for the Iss 2 fuzz built in the style of a BC183KA Fuzz Face. This kit includes all of the resistors, capacitors, and transistors used on the included circuit board. For the BC183KA style parts kit, a pair of BC183A transistors are included.

The Mod® Electronics MOD 102 is a great place to start for those interested in building their own tube amp. It is based on a classic American tube-circuit design combined with a British style Class A output tube section. At low volume it produces a clean chimey tone that moves into smooth overdrive at higher volumes. All parts are included along with a pre-drilled steel chassis, wire and tubes (1 EL84 and 1 12AX7). Puts out at least 5 watts. The chassis layout is open for easy assembly using the clear, easy to follow instructions.

The K-GMOD-5 is a vintage style wiring kit for Les Paul toggle switches and output jacks. Use this kit to upgrade your current Les Paul switch and jack to high quality parts.

The Mod® Electronics Suspended Chime has two powerful effects in one pedal - chorus and chorus/delay. The Suspended Chime features a blend knob which allows you to go from subtle to lush chorus effect in either set up. Using the toggle switch, you can add a 190 millisecond delay to the chorus introducing special depth to your tone. Varying the dry/wet mix can fatten your rhythms or produce a shimmering 12-string sound. The Suspended Chime kit comes equipped with an LED indicator and industry standard 9 volt center negative power jack. MOD® Kits are designed to give both novice and experienced musicians the opportunity to build their own amps and effects pedals. All kits come with easy to follow instructions and use point to point wiring. Pre-drilled enclosure and all parts are included. All you need to provide are hand tools, a soldering iron and solder. All effects pedals operate on a 9V battery.

PCB and parts kit for the Supa Fuzz. This is based on the classic PCB version produced by Marshall. This kit includes all of the resistors and capacitors used on the included circuit board. The germanium PNP transistors are not included such that customers can select and test their own.

The Maxon OD-9 is the original Tube Screamer TS9 circuit built by the company that designed this immensely popular overdrive pedal. They left no boxes unchecked by including a genuine JRC4558 and the only departure from the original is the inclusion of true bypass switching, a modern necessity. The OD-9 offers slightly more gain than the OD808.
Features

• Identical to the original circuit and featuring the JRC4558 IC chip
• Natural tube-like overdrive that smoothly responds to dynamic signals
• True Bypass Switching
• Low noise mechanical switch
• LED indicator for effect on/off
• DC power or 9V battery
• Made in Japan

The K-GMOD-7 is a vintage style wiring kit for SG guitars. Use this kit to upgrade your current SG electronics to high quality parts. This kit also includes a treble bleed mod for the volume pots to enhance clarity with lower settings and comes with detailed instructions and all the parts you need to make your modification.

Junior Genius Kits are built for experimentation, learning and fun! Experience the joy of seeing your first LED light up. The Blinky Lights Kit leads you through 10 core activities, from a simple LED circuit up to more advanced transistor LED blinky light circuits, using standard parts on a real-world breadboard. Learn about voltage and current by using LEDs, resistors, capacitors and transistors. You'll be able to build circuits using a schematic diagram, and there's plenty of help to get you there. Simple examples make it easy to grasp the basics and 'What's Happening' and 'Things To Try' sections encourage you to dig deeper. You will get valuable assembly and troubleshooting experience as you learn to use a great experimentation tool, the solderless breadboard. Real hands-on experience means greater educational value. This next-generation science kit doesn’t seal the parts into simplified plastic blocks.

PCB and parts kit for the HS Treble Booster. This is based on the more common silicon version that used a 2N4061 transistor. This kit includes all of the resistors, and capacitors used on the included circuit board. A 2N4061 transistor is included. In addition to the PCB parts, a footswitch, jacks, battery snap, and ground lug are all included in this parts kit.