Luthier Parts & Tools

Fits SKU# P-GB500-X Now you can install a Bigsby Vibrato on your guitar without drilling any holes!

Bob Smith Industries™ Insta-Cure+™ Medium Gap Filling Cyanoacrylate. A must have for luthiers! Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps or the parts to be glued don’t fit perfectly. Medium viscosity super glue is the most common glue used in many luthiery applications due to it’s cure time and viscosity. Recommended for binding repair and small poly finish touch ups. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. To speed up curing time use the Insta-Set accelerator!

Bob Smith Industries™ Insta-Cure™ Super Thin Cyanoacrylate. A must have for luthiers! Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds (1-3 sec.). Surfaces to be bonded must be tight fitting (no visible gaps) and should be held together or clamped while you apply the CA around the edges of the seam. For glue applications with small gaps or looser fitting joints the higher viscosity Insta-Cure+™ is recommended.

• Water-thin consistency
• 1-3 second cure time
• For tight fitting applications
• Available in 1oz. and 2oz. sizes

WARNING: These products are eye and respiratory irritants. Product can bond skin instantly. Keep away from children!

Original Fender® set of two threaded steel bridge-pivot screws used to mount two-point synchronous tremolo systems on American, Ultra, and American Standard Stratocaster® models (and some Custom Shop Stratocaster models) manufactured from 1986-present.
Features:

• Set of two threaded steel bridge-pivot mounting screws
• For American, Ultra, American Standard and some Custom Shop Stratocaster models (1986-present).

Genuine Bigsby anchor bars for vibrato units. Anchor bars are also referred to as pivot bars and string shafts.

Original Fender® inserts for American Standard Tremolo, set of 2.

Pair of standard stop bar anchor bushings for stud mounts with fine knurling and fits most guitars using a 0.986” body depth for the anchors. Made from zinc. Pairs with P-GKLU-KLP1099X studs. Studs sold separately.

High quality USA made steel anchor bushings available in long or short lengths with a coarse or fine knurl for a variety of stop tailpiece uses. These bushings fit 5/16 – 24 US Threaded studs. Studs sold separately.

Three-ply black/white/black Stratocaster style back plate with 6 mounting holes.

Genuine Bigsby mounting screws pack. This pack comes with a variety of Bigsby screws common to many of their tremolo units. Item Qty BigSby Part Number Body Mount Screws 4 0495-1927 Hinge Mount Screws 4 0495-1923 Handle Bracket Set Scre 2 0495-1931

Genuine Bigsby spring pack. This pack comes with all of the Bigsby spring sizes along with the nylon spring washer and fiber handle washer. Item Qty BigSby Part Number 11/16" long spring 1 0495-1964 7/8" long spring 1 0495-1967 1" long spring 1 0495-1975 1 1/8" long spring 1 0495-1978 Handle washer 1 0495-2331 Spring washer 1 0495-0410

Original, made in USA, P.A.F.-correct bobbins for making humbucker pickups. These screw side bobbins are made of butyrate molded in casts of the originals and feature a 49.2mm spacing.

Original, made in USA, P.A.F.-correct bobbins for making humbucker pickups. These screw side bobbins are made of butyrate molded in casts of the originals and feature a 49.2mm spacing.

MicroTilt disk bolt, 1/4-28 x 1⁹⁄_16". Genuine Fender® 3 bolt neck micro tilt adjust mounting bolt. This bolt goes in the lower location in the Fender 3-bolt neck plate. This bolt is secures your neck angle adjustment once you have made your neck tilt angle change with the set screw.

Made in U.S. vintage spec ABR-1 bridge with no retaining wire and nylon saddles. Hardware sold separately. See P-GKLU-KLP1273N for a complete set. The bridge uses string tension along with the set screws to secure the nylon saddles onto the bridge.

• Post spacing: 2.93 inches (74.5mm)
• Radius: 12 inches (30.48cm)
• String Spacing: 10.4 mm

Made in U.S. vintage spec ABR-1 bridge with no retaining wire and plated brass saddles. Hardware sold separately. See P-GKLU-KLP127X for a complete set. The bridge uses string tension along with the set screws to secure the brass saddles onto the bridge.

• Post spacing: 2.93 inches (74.5mm)
• Radius: 12 inches (30.48cm)
• String Spacing: 10.4 mm

Made in U.S. vintage spec ABR-1 bridge made to the same specifications as the original 1950s version. Wired with plated brass saddles. Mounting hardware sold separately. The bridge features the vintage-style retaining wire that secures the plated brass saddles and intonation screws onto the bridge.

• Post spacing: 2.93 inches (74.5mm)
• Radius: 12 inches (30.48cm)
• String Spacing: 10.4 mm

Made in U.S. vintage-spec ABR-1 bridge made to the same specifications as the original 1950s version. Wired with raw brass saddles. Mounting hardware sold separately. For a full set with all hardware included, please see P-GKLU-KLP128X. The bridge features the vintage-style retaining wire that secures the raw brass saddles and intonation screws onto the bridge.

• Post spacing: 2.93 inches (74.5mm)
• Radius: 12 inches (30.48cm)
• String Spacing: 10.4 mm

Genuine Bigsby® bridge assembly for use with Bigsby vibrato units.

Genuine Bigby bridge for Guild Special Archtop guitars. This bridge has a 2-1/16" string spacing with a 3” stud spacing.

Genuine Bigsby® Sorkin bridge assembly for use with Bigsby vibrato units. The Sorkin bridge is also known as the bowtie bridge.
2 13/16” stud spacing.

Genuine Bigsby® conventional Telecaster bridge for use with Bigsby vibrato. This is the stock bridge assembly used in B16 vibratos.
2 13/16” stud spacing.

Genuine Fender USA vintage Stratocaster tremolo assembly. Features 'FENDER' stamped saddles

(Non-serialized) Bridge Plate. Used on American Vintage Series Telecaster® guitars manufactured from 1986 to the present. Mounting hardware included.
The standard version comes with 3 brass vintage Tele® saddles and the Road Worn version features three vintage steel saddles.