Luthier Parts & Tools

Gotoh locking nuts are superior quality locking nuts that directly replace original Floyd Rose and Floyd Rose style locking nuts. Top mount. Width: 41mm (1 5/8") Radius: 360mm Included: Retainer bar, screws, wrench. Locking nut for Floyd Rose tremolo units.

Gotoh locking nuts are superior quality locking nuts that directly replace original Floyd Rose and Floyd Rose style locking nuts. Top mount. Width: 1-11/16'' (43mm). Included: Retainer bar, screws, wrench. Locking nut for Floyd Rose tremolo units.

Pre-slotted black bone nuts for Gibson necks with a 12” radius. A 12” fingerboard is the common radius used on most Gibson guitars. The bone used for the pre-shaped and pre-slotted nuts is dyed black using a process that results in a fully black nut.

• Height - 9.3 mm
• Width - 43.4 mm
• Thickness - 4.8 mm
• Radius - 12 in.

Pre-slotted black bone nuts for Stratocaster®, Telecaster®, and other Fender® necks with a 7.25” radius. A 7.25” fingerboard radius originated in the early 1950s and was used for most Fender® electric instruments until the 1980s.

• Height - 5.4 mm
• Width - 42.86 mm
• Thickness - 3.3 mm
• Radius - 7.25 in.

For a version of this nut with a 9.5” radius, see P-GTNN21.

Pre-slotted black bone nuts for Stratocaster®, Telecaster®, and other Fender® necks with a 9.5” radius. A 9.5” fingerboard has been the standard Fender® neck radius since the 1980s. The bone used for the pre-shaped and pre-slotted nuts is dyed black using a process that results in a fully black nut.

• Height - 5.4 mm
• Width - 42.86 mm
• Thickness - 3.3 mm
• Radius - 9.5 in.

For a version of this nut with a 7.25” radius, see P-GTNN20.

High quality bone nut blank with extra length, width, and height. These blanks leave the shaping, slotting, and polishing to you so you can control your own custom feel and appearance.

• Measures 45mm x 10mm x 4.95mm
• Sold individually

High quality bone nut blank with extra length, width, and height. These blanks leave the shaping, slotting, and polishing to you so you can control your own custom fit and appearance.

• Measures 52.5mm x 10mm x 4.95mm
• Sold individually

Bone nut for Fender® , 44.45mm x 3.3mm x 6.35mm at highest point with flat bottom.

Bone nut for Gibson®, 43mm x 5.9mm x 8mm at highest point with flat bottom.

High quality bone nut blank with extra length, width, and height. These blanks leave the shaping, slotting, and polishing to you so you can control your own custom fit and appearance.

• Measures 56 mm x 11 mm x 6.35 mm
• Sold individually

This brass nut blank will work for most Fender® and similar style guitars and basses. It is NOT slotted and does require final shaping and fitting to exact size.

• Thickness = 9/64 inches (3.47mm)
• Flat Bottom Length = 1 11/16 inches (43 mm)
• Height at ends = 13/64 inches (5.25mm)
• Height at middle = 15/64 inches (6mm)

LSR roller nut reduces friction that can cause tuning instability. Comes with instructions, mounting hardware and Wilkinson® adapter for older Strat® Plus models. Used on American Deluxe HSS guitars. Kit Includes: LSR Nut, Shims, Mounting Screws and Bezel Adapter (for Retrofitting to Wilkinson® Nut Equipped Guitars) Will Accommodate String Gauges from .008 to .056. Some modification may be required.

Original Fender pre-slotted bone nut for Teles and Strats.

Genuine Fender® pre-slotted melamine nut for Telecaster and Stratocaster guitars. This nut has 9 1/2 in. top radius and 7 1/4" bottom radius with an overall length of 1.695 in.

High-quality Micarta (synthetic bone) pre-slotted string nut for use on American Standard Precision Bass and other U.S.- and Mexico-made basses with 9.5"-radius fingerboards.

The Zero Glide® Replacement Nut System borrows the “zero fret” concept to reduce string contact in the nut by up to 93%, increasing tuning stability, playability, and open string tone. It only takes a few minutes to install with absolutely no permanent alteration to your instrument. Zero fret wire included (multiple sizes). Comparison Standard Nut Zero Glide Open String Tone Absorbs energy. Fret reflects energy, making the open strings more vibrant. Tuning Friction causes string binding. 93% less surface area. More accurate tuning. String Bend/Whammy Bar Whammy bars and string bends cause the strings to bind in the nut and not return to pitch Reduces string binding and "returns to zero" after every tug of the whammy bar or bend Durability Slots wear down over time. Minimal wear.

This graphite nut blank will work for most Fender® and similar style guitars and basses. It is NOT slotted and does require final shaping and fitting to exact size. It has a radiused bottom.

• Length = 2 1/64 inches (51.25mm)
• Height = 11/64 inches (4.55mm)
• Thickness = 1/8 inch (3.1mm)

Graphite nut for Fender® This graphite nut will work for most Fender® and similar style guitars. It is slotted, but does require final shaping and fitting to exact size.
PLEASE NOTE: Because this nut tapers in both thickness from top to bottom and height on the fret board side vs. the headstock side all measurements for those dimensions were taken at the center of the nut.

• Length = 1 41/64 inches (41.52mm)
• Height #1 (fretboard side) = 13/64 inches (5.06mm)
• Height #2 (headstock side) = 13/64 inches (5mm)
• Thickness at bottom = 9/64 inches (3.46mm)
• Thickness at top = 1/8 inches (3.1mm)

This graphite nut will work for most Gibson® and similar style guitars and basses. It is slotted but does require final shaping and fitting to exact size. PLEASE NOTE: Because this nut tapers in both thickness from top to bottom and height on the fret board side vs. the headstock side all measurements for those dimensions were taken at the center of the nut.

• Length = 1 23/32 inches (43.75mm)
• Height #1 (fretboard side) = 5/16 inches (7.81mm)
• Height #2 (headstock side) = 9/32 inches (7mm)
• Thickness at bottom = 15/64 inches (6.1mm)
• Thickness at top = 3/16 inches (4.78mm)

High-quality solid-brass string nut as used on the Yngwie Malmsteen Stratocaster®, for use with Stratocaster and Telecaster® guitars.
Designed for 9.5"-radius fingerboards and pre-slotted with string location grooves to simplify spacing and positioning during final slot filing.
Features:

• High-quality solid-brass string nut
• For 9.5" fingerboard radius
• Pre-slotted
• 9.5" (241mm) top and bottom radius
• 1.620” (41.15mm) wide

Stratocaster guitar nut - plastic construction

Plastic electric guitar nut.

The PQ-M100-00 is a TUSQ nut blank specially designed to be used on Martin style guitars. It has an angled bottom and needs to be slotted. Dimensions:

• Length - 1.89 in. (48.01mm)
• Width - 0.226 in. (5.74mm)
• Height - 0.42 in. (10.67mm)

The PQ-1720-00 is the perfect option to upgrade the nut on your six string guitar. It is pre-slotted for a quick and simple install. It is a very common nut used in the Godin family of guitars.
Dimensions:

• Length - 1.695 in. (43.05mm)
• Width - 0.204 in. (5.18mm)
• Height - 0.403 in. (10.24mm)
• E to E - 1.415 in. (35.93mm)