Luthier Parts & Tools

Adhesive - Bob Smith Industries, Insta-Cure Gap Filling
Bob Smith Industries™ Insta-Cure+™ Medium Gap Filling Cyanoacrylate. A must have for luthiers! Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps or the parts to be glued don’t fit perfectly. Medium viscosity super glue is the most common glue used in many luthiery applications due to it’s cure time and viscosity. Recommended for binding repair and small poly finish touch ups. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. To speed up curing time use the Insta-Set accelerator!
Starting at $5.50
Adhesive - Bob Smith Industries, Insta-Cure Super Thin
Bob Smith Industries™ Insta-Cure™ Super Thin Cyanoacrylate. A must have for luthiers! Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds (1-3 sec.). Surfaces to be bonded must be tight fitting (no visible gaps) and should be held together or clamped while you apply the CA around the edges of the seam. For glue applications with small gaps or looser fitting joints the higher viscosity Insta-Cure+™ is recommended.
  • Water-thin consistency
  • 1-3 second cure time
  • For tight fitting applications
  • Available in 1oz. and 2oz. sizes

WARNING: These products are eye and respiratory irritants. Product can bond skin instantly. Keep away from children!
Starting at $5.50
Caliper - Digital, highly-accurate for luthiers
This Luthier's Digital Caliper has a custom jaw notch for accurately measuring fretwire crown height (the height above the fretboard). This is essential for comparing new wire to original wire. And there's a notch on the depth gauge to measure fret height on the instrument.
  • Measures fret height before AND after fret installation
  • Accurate readouts in inches or millimeters
  • A must for all precision guitar work
$44.95
Care Pack - Lizard Spit, for Guitar / Bass
This Lizard Spit Guitar and Bass Care Pack contains 4 oz. Fretboard Conditioner, 4 oz. Guitar Polish, and a Lizard Spit Micro Fiber Cloth, everything you need to keep your guitar or bass in good condition and looking brand new!
$21.00
Chemical Polishing File - Flat, clean tooth pattern
CP files have special file tooth pattern and it keeps file clean without clogging. Easy to control and fast to file clean with light strokes.
Starting at $18.15
Chisel - Flat, Japanese, Micro, 1.1mm
Small flat chisel with an offset handle allowing this tool to easily get into tight spaces for luthier work. The 1.1mm blade is made of high quality HSS steel and is perfect when precision is required for nut slots and elsewhere. Made in Japan.
$35.95
Chisel - Flat, Japanese, Steel, Tataki-Nomi
High quality made in Japan flat chisels for luthier work. These chisels have a blade hardness of HRC63 and a total length of 225mm. The hardwood handle features a flat end for hammering,
Starting at $16.95
Cloth - Lizard Spit, Micro Fiber for polishing
Baby blue micro fiber cloth for use with Lizard Spit or other polishing products.
$6.25
Drill Bit - two step, for installing vintage tuners
Two-step drill bit for drilling two-step holes. HSS material. Can be used to install vintage type tuners. 7.8 mm inner diamter, 9.9 mm outer diameter.
$59.46
Save 15%
Originally: $69.95
Feeler Gauge - 20 Sizes, for measuring gaps / clearance
Package of 20
This precise set of 20 feeler gauges in the luthier's workshop can perform a wide variety of functions to measuring with string action to measuring the correct nut slot depths, fret slot width, string to fret clearances, and other hardware installation work, these ground steel feeler gauges are marked in both metric and imperial measurements for easy use.
$8.25
File - Diamond, for Frets, Straight
Double sided diamond fret file. Easily the best choice for fret crowning, diamond files cut in two directions (push and pull) rather than one with no chatter giving you a smoother fret after the crowning process File cutting surface is impregnated with diamonds to give you a smooth cut with long lasting durability.
  • Made of solid steel with diamond cutting surface.
  • Soft rubber coating on the handle
  • 5-3/4” cutting surface
  • Double sided to cover different fret sizes
$62.95
File Set - for Nut And Saddle Shaping
Package of 3
Set of files for control over shaping nuts and saddles.
  • Half-round shape
  • Flat shape
  • Triangle shape
$57.00
File Set - Needle files, 5 types, for precision work
Package of 5
Set of files for precision work.
Includes:
  • flat
  • half round
  • round
  • square
  • three square (i.e. triangular)
Starting at $15.20
Fingerboard Guards - 2 Sizes, for protecting frets
Package of 2
Designed to protect the fingerboard when doing work on your frets. These shields are indispensable when doing any sort of fret work. Being only .010” thick they can bend to accommodate and fingerboard radius. Made of 304 spring stainless steel.
Comes with 2 sizes: 3-1/8" x 7/8" x .010" - 1/4 inch protection on either side of the fret, 3-1/8"" x 0.59" x .010"" - 3/8 inch protection on either side of the fret
$4.25
Fret / Fingerboard Leveler - for checking frets
Fast, accurate leveling tools for the pro shop. This heavyweight steel tube is precision-ground for flatness on the narrow sides. Attach abrasive to quickly level frets or unfretted fingerboards.
Each heavyweight rectangular 1" x 2" steel tube is precision-ground for flatness on two opposite sides. The tool's edges are smooth to prevent gouging.
Starting at $11.95
Fret Bender - for creating radius in or flattening Fret Wire
Multi-functional Fret Bender - bend or staighten either bulk fretwire or pre-cut short piece fret wire precisely and quickly! For bending fret wire, crank a length of fretwire through the fret bender, and it comes out curved and ready to install in a radiused fretboard. Get a perfect bend on enough wire for a whole guitar in just seconds. Precisely radiused fretwire makes your fretwork fast, accurate, and professional.
Can be mounted to a workbench by using the two 5/16” bolt holes.
$69.95
Fret Collars - Dunlop, System 65, for fret polish without taping
Package of 2
The Dunlop System 65 Fret Collars include everything you need for a quick fret polish without the need for taping the entire neck. Two sizes of flexible steel collars are included, 0.125 and .080.
$15.95
Fret Cutter - 190mm, for Trimming Fret Wire
Fret Cutters. Use to trim the ends of new fret wire close to the fingerboard without leaving marks. Made in Japan. Dimensions:
  • 190 mm total length
  • 27 mm jaw width
$37.95
Fret Cutter - Carbon Steel, for Cutting Stainless Steel Fret Wire
High quality carbon steel fret cutters for use with stainless steel fret wire. These newly designed cutters improve accuracy providing a flatter cut than other versions. Additionally the blades are designed for improved durability. The cutters can also be locked in the closed position for protection when not in use.
$39.95
Fret File - 600 grit, 3 radiuses, diamond, for Crowns
600 grit diamond-plated file. 3 different, (small, medium, large) radiuses in one file. 130mm file length, 230mm total.
$104.95
Fret File - Diamond, offset, for dressing and shaping frets
Diamond fret file with offset shape for more comfortable fret dressing and improved clearance over the guitar body at high frets. Both full length concave filing grooves (for medium and wide fretwire) uniformly coated with micro industrial diamond particle.
Starting at $66.95
Fret File - for Filing Fret Ends, pencil shape
Made in Japan. File specially designed for fret end work. Used for rounding fret ends and deburring. Size small = 1 mm for small frets. Size medium = 2 mm for medium frets. Size large= 3 mm for large frets.
$34.25
Fret File - for leveling across multiple frets
For filing straight across multiple frets to ensure that they are level.
$17.75
Fret Files - for Filing Fret Crowns
Solid steel crowning files with dual cutting edges for precision fret crowning. These should be in any luthier’s tool kit!
  • Made of solid steel
  • Soft rubber coating on the handle
  • Double sided (both sides are the same size)
  • 4-3/16” cutting surface
  • Available in three sizes to cover most fret sizes (small,medium,large)
Starting at $28.95