You are here

Maintenance Products

Filter these results
Sort By:
products per page
View Mode: List View · Grid View
S-C10-8602Belt and Drive Non-Slip - GC Electronics
Prevents slippage in mechanical or electro-mechanical devices, which are driven with cords, belts, pulleys and drives. Restores proper functions on belts and drive pulleys in turntables, record changers and tape recorders, especially where the rubber parts have hardened and/or become slick and cause slippage.
  • Color: Clear to light brown
  • Specific Gravity: 0.91
  • Flash point: 54°F
  • Freezing Point: <90°C
  • Solubility in Water by wt.: 100% at 20°C
$7.95
$7.16
You save: 10%
Click to read more
S-C10-8109Heat Sink Compound - silicone, Type Z9, 1 oz
Type Z9, 1 fluid ounce. Silicone base, extra high-efficiency heat transfer. Made in USA. For mounting transistors, diodes, rectifiers, and resistors. Thermal joint compound for any device where efficient cooling is desired.
  • For effective transfer of heat between components & heat sinks
  • Will not dry or harden
  • White paste

Grease-like consistency; opaque white in color; zero bleed; very stable at elevated temperatures; excellent thermal resistance and high thermal conductivity; efficient thermal coupler; effective and positive heat sink sealers and heat transfer agent. The product offers high thermal conductivity, virtually no bleed or evaporation over a wide operating temperature range. It will not harden, dry out or melt after 1,000 hours at 200°C. Meets Mil-C-47009 and Mil-C-47113.
$6.75
$6.08
You save: 10%
Click to read more
S-C10-4702Corona Dope - GC Electronics, lacquer coating, 2 oz.

Corona Dope is useful for insulating components, circuits and assemblies. It has high dielectric strength and is especially useful where high voltages are involved. Also has excellent arc and corona resisting properties and protects surfaces against moisture. Cures in 20 minutes at room temperature.



  • Color: Black
  • Specific Gravity: 0.9
  • Dielectric Strength: 3800 V/Mil
  • Softening Point: 180°C to 190°C
  • Temperature Range: Up to 340°F
  • Viscosity @ 25°C: 220 cps

$9.98
$8.98
You save: 10%
Click to read more
S-CCW100PPen - Caig, Circuit writer, for drawing traces

Circuit Writer precision conductive ink dispenser makes instant traces on most surfaces(epoxy, glass, metal). Draw traces on circuit boards, repair defective traces, make jumpers and shield electronics, design prototype circuits, repair rear-window heater traces. Silver based solution, 7ml pen dispenser.


$23.95
$21.56
You save: 10%
Click to read more
S-CIS-808Solvent - Silicone Rubber Adhesive, IS-808, Translucent
Momentive IS-808 translucent adhesive. Made in USA.
Instructions:
Remove dirt, grease, or moisture from surface to be sealed or bonded. Dry surface or allow to dry thoroughly. Cut nozzle to desired bead size. Tool within 10 minutes. Typical tack-free time about 20 minutes. Typical curing time about 24 hours. Length of time for full cure depends upon thickness of application and other factors such as weather and temperature. See datasheet for complete information. NOTE: Corrodes copper, brass and sensitive metals. NOT FOR USE ON STOVEPIPES, FIREPLACES OR UNDER WATER.
$9.95
$8.96
You save: 10%
Click to read more
S-CCOLORBOND-BLKRefinisher - Color Bond, Black, for Plastic, Leather, and Vinyl
Color Bond leather, vinyl & hard plastic black refinisher. Proprietary formula penetrates surface and molecularly bonds to permanently seal in the color. Great for tolex. Prepare upholstery for refinishing with S-CCOLORBOND-PREP.
$16.00
$14.40
You save: 10%
Click to read more
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Maintenance Products