You are here

Maintenance Products

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(10 pages)
S-F502XAdhesive - Bob Smith Industries, Insta-Cure Gap Filling

Bob Smith Industries™ Insta-Cure+™ Medium Gap Filling Cyanoacrylate. A must have for luthiers! Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps or the parts to be glued don’t fit perfectly. Medium viscosity super glue is the most common glue used in many luthiery applications due to it’s cure time and viscosity. Recommended for binding repair and small poly finish touch ups. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. To speed up curing time use the Insta-Set accelerator!


Starting at $5.50
Click to read more
S-C10-4702Corona Dope - GC Electronics, lacquer coating, 2 oz.

Corona Dope is useful for insulating components, circuits and assemblies. It has high dielectric strength and is especially useful where high voltages are involved. Also has excellent arc and corona resisting properties and protects surfaces against moisture. Cures in 20 minutes at room temperature.



  • Color: Black
  • Specific Gravity: 0.9
  • Dielectric Strength: 3800 V/Mil
  • Softening Point: 180°C to 190°C
  • Temperature Range: Up to 340°F
  • Viscosity @ 25°C: 220 cps

$9.98
Click to read more
S-CPOLISH-XPlastic polish - Novus, full plastic treatment / restoration kit
Package of 3

By using this kit and few simple techniques, you can actually add life to plastic and keep it looking new. Best of all, you don't have to be a pro to get professional results. No. 3 removes heavy scratches, and No. 2 polishes out lighter imperfections. After removing the abrasions with No. 3 and No. 2, apply No. 1 to clean and shine plastic. Three-step system provides a clean, highly polished static- and dust-free surface.


Starting at $9.70
Click to read more
S-C10-8109Heat Sink Compound - silicone, Type Z9, 1 oz

Type Z9, 1 fluid ounce. Silicone base, extra high-efficiency heat transfer. Made in USA. For mounting transistors, diodes, rectifiers, and resistors. Thermal joint compound for any device where efficient cooling is desired.



  • For effective transfer of heat between components & heat sinks
  • Will not dry or harden
  • White paste


Grease-like consistency; opaque white in color; zero bleed; very stable at elevated temperatures; excellent thermal resistance and high thermal conductivity; efficient thermal coupler; effective and positive heat sink sealers and heat transfer agent. The product offers high thermal conductivity, virtually no bleed or evaporation over a wide operating temperature range. It will not harden, dry out or melt after 1,000 hours at 200°C. Meets Mil-C-47009 and Mil-C-47113.


$6.75
Click to read more
S-CD100L-2CDeoxIT® D100L - Caig, squeeze tube
DeoxIT® D100L squeeze tube chemically improves metal to metal connections and contacts.100% solution, 2 ml,(Applications = 50 ± drops, 0.04 ml/drop).
$4.70
Click to read more
S-F506XAdhesive - Bob Smith Industries, Insta-Set Foam, Pump Spray

Bob Smith Industries INSTA-SET™ CA (super glue) Accelerator. INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET™ significantly enhances a joint’s strength. For difficult to bond materials, INSTA-SET™ can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET™ is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastic and white foam.



  • Convenient pump spray (2oz.

Starting at $5.95
Click to read more
S-CD100L-25CDeoxIT® D100L Liquid - Caig, needle dispenser

DeoxIT® D100L Liquid, 100% solution. Chemically improves metal to metal connections and contacts. Dissolves corrosion, improves contact, and protects surfaces


$31.45
Click to read more
S-CF100S-L2DeoxIT® Fader F100 - Caig, 100% spray

DeoxIT® Fader Spray (formerly CaiLube MCL, MCL100S-L2) is a precision lubricant for moving contact surfaces (faders, switches, potentiometers and other mechanisms with sliding surfaces). It replenishes lubrication lost on surfaces that have been cleaned with solvents or other cleaning solutions.


$18.95
Click to read more
S-CDFG-213-1DeoxIT® Fader Grease - Caig
DeoxIT® FaderGrease was specifically formulated to improve conductivity and lubricate conductive plastic and carbon compound faders, switches and other mechanisms with sliding surfaces.
Provides clearer audio, clearer video, and reliable data.
Over time these components lose their original lubrication from wear and/or repeated cleaning. Dust, dirt, smoke, drink spills and other contamination also degrade the components' lubricant. Re-lubrication is necessary to avoid excess wear and abrasion to the plastic surfaces. 28 grams
$15.95
Click to read more
S-CDP5S-6DeoxIT® - Caig, pump spray
DeoxIt Pump Spray 25% concentrate solution. Non-flammable. 150ml. May be shipped by air to US and other countries.
$22.95
Click to read more

Pages

(10 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Maintenance Products