New Products

Turret Strip - 16 Lugs, Two Rows, U-style, Extra Dense
Two rows of 8 U-style terminals (16 total) on a black board. This U-style terminal strip is extra dense with 6.35mm terminal spacing allowing for even more densely populated point-to-point builds. The boards are 0.063” thick.
$2.15
Turret Strip - 24 Lugs, Two Rows, U-style, Extra Dense
Two rows of 12 U-style terminals (24 total) on a black board. This U-style terminal strip is extra dense with 6.35mm terminal spacing allowing for even more densely populated point-to-point builds. The boards are 0.063” thick. This 24 lug turret board is a close match to the board found in Burns BuzzAround pedals.
$2.95
Rubber feet - 7/16” Dome Shape, Embedded 6-32 Screw
Dome shaped rubber feet with an embedded 6-32 machine screw. These feet have a 0.4375 inch diameter and have a 0.25 inch screw length. The embedded screw provides a sleek appearance. These are great feet and can also be used as bumpers.
$0.95
Turret Strip - 12 Lugs, Two Rows, U-style, Extra Dense
Two rows of 6 U-style terminals (12 total) on a black board. This U-style terminal strip is extra dense with 6.35mm terminal spacing allowing for even more densely populated point-to-point builds. The boards are 0.063” thick.
$1.95
Safety Glasses - Impact Resistant, ANSI Z87.1+ Rated, Clear
ANSI Z87.1+ rated eye protection. These safety glasses have scratch resistant lenses with UV protection.
$3.50
Op-Amp - OP275, Dual, Bipolar/JFET, Audio, 8-Pin DIP
OP275 dual audio op amp in an 8-pin DIP package. The OP275 is the first amplifier to feature the Butler Amplifier front end. This new front end design combines both bipolar and JFET transistors to attain amplifiers with the accuracy and low noise performance of bipolar transistors, and the speed and sound quality of JFETs. Total Harmonic Distortion plus Noise equals that of previous audio amplifiers, but at much lower supply currents. A very low l/f corner of below 6 Hz maintains a flat noise density response. Whether noise is measured at either 30 Hz or 1 kHz, it is only 6 nVHz. The JFET portion of the input stage gives the OP275 its high slew rates to keep distortion low, even when large output swings are required, and the 22 V/µs slew rate of the OP275 is the fastest of any standard audio amplifier.
$4.25
Switch - Carling, Toggle, SPST, Ball Actuator
Heavy duty Carling SPST (Single Pole, Single Throw) toggle switch with a vintage-style ball actuator. This latching On-Off switch is a great option for vintage amps and electronics or new builds with vintage styling. Rated for 3A 250V, 6A 125V, AC/DC.
$8.95
PCB - Vintage Style Circuit Board, Iss. 1 Fuzz, Phenolic Board
Iss. 1 fuzz PCB made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This PCB is a recreation of the iss. 1 circuit board found in classic Fuzz Face pedals. When drawing the layout, multiple originals were closely referenced to ensure a proper match and fit. The copper traces are gold plated providing protection from corrosion indefinitely. This classic board fits the mounting holes on both original and reproduction Fuzz Face enclosures.
$4.50
StripBoard - Single Sided, 3.04” x 1.55”, Vintage Spacing, Phenolic Board
Stripboard made with a phenolic substrate. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This stripboard features a 0.15” vintage spacing. This spacing is great for vintage-style builds and more easily accommodates axial capacitors and other larger sized vintage parts like resistors and transistors. The board has a 20x10 grid (10 strips) and easily fits into 1590BB style enclosures and larger vintage-style fuzz enclosures. Each strip is gold coated making soldering easier than most protoboards and also ensures a long shelf life. Features:
  • High-quality 1.6mm phenolic circuit board
  • Gold coated strips
  • 20 x 10 holes (10 strips)
  • 3.04” x 1.55”
$2.95
StripBoard - Single Sided, 3.04” x 1.55”, 0.1” Spacing, Phenolic Board
Stripboard made with a phenolic substrate. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This stripboard features standard 0.1” (2.54mm) spacing. The board has a 30x15 grid (15 strips) and easily fits into 1590BB style enclosures and larger vintage-style fuzz enclosures. Each strip is gold coated making soldering easier than most protoboards and also ensures a long shelf life. Features:
  • High-quality 1.6mm phenolic circuit board
  • Gold coated strips
  • 30 x 15 holes (15 strips)
  • 3.04” x 1.55”
$2.75
Transistor - 2N2614, Germanium, TO-1 case, PNP
2N2614 PNP germanium transistors. The 2N2614 is a popular PNP for fuzz pedals and other effects. The 2N2614 was popularly used in the Maestro Fuzz Tone FZ-1a pedal.
$3.95
Transistor - 2N408, Germanium, TO-1 case, PNP
2N408 PNP germanium transistors. The 2N408 is a popular PNP for fuzz pedals and other effects. The 2N408 was popularly used in the germanium version of the Fuzzrite by Mosrite along with the 2N2613.
$4.50
Battery - 9V, Carbon Zinc, GP, Greencell, Extra Heavy Duty
Extra heavy duty carbon zinc batteries from GP. The GP Greencell 9V is a favorite for fuzz pedals and is the stock battery for many boutique builders such as D*A*M and others. Additionally, these batteries are a great choice for any low current battery powered pedal or other devices.
$1.95
Transistor - 2SD187, Germanium, TO-1 case, NPN
2SD187 NPN germanium transistors. The 2SD187 is a popular NPN for fuzz pedals and other effects. Like the AC127, the NPN polarity of the 2SD187 allows for use with standard pedal power supplies.
$3.95
Chassis - Three Knob Fuzz, Pressed Steel
Pre-drilled three knob pedal enclosure made of pressed steel. This large enclosure is a close match to the original enclosures found on various vintage fuzz effects such as the Vox Tone Bender MKIII, Rotosound Fuzz, and Park Fuzz Sound. It features three holes for potentiometers, two top mounted holes for ⅜” jacks, and a footswitch hole. Comes with 4 rubber feet and a pack of mounting screws(packaged separately) for attaching the bottom plate.
  • Footswitch Hole Diameter: 0.492 in. (12.5mm)
  • Potentiometer Hole Diameter: 0.294 in. (7.47mm)
  • Jack Hole Diameter: 0.447 in. (11.35mm)
$19.95
On Backorder
Chassis Box - Hammond, 1590J, Diecast, 5.7” x 3.7” x 1.9”
Large 5.709” x 3.37” x 1.933” Hammond 1590J enclosures. This enclosure is a great option for dense builds and is a popular choice for vintage style fuzz pedals with plenty of room for point to point wiring.
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
  • Dimensions shown are exterior dimensions.
  • Add 0.16" to enclosure depth for lid.
$13.25
Knob - Rogan, Rickenbacker Style, Diamond Pointer, Brown & Gold
High-quality USA made knobs from Rogan Corp. These solid phenolic knobs feature a brushed metal inlay in their unique diamond shaped grip. Often referred to as TV or cooker knobs, these genuine Rogans are used in a variety of Rickenbacker guitars and basses. In addition to the diamond shaped grip, they feature a large skirt and a small notched indicator. Fits ¼" shaft potentiometers.
  • Height: 0.635 in.
  • Length: 1.497 in.
  • Fits ¼" shaft with set screw
$8.95
Label - High Voltage Warning, Large, Sticker
Package of 4
High voltage warning label for amplifiers and other equipment. These stickers are a great option for labeling equipment and builds as high voltage whenever necessary. The sticker is a single piece that must be cut to size using scissors or a paper cutter to make a total of four labels. This style of label is perfect for rear panels on amplifiers and other equipment.
$1.25
Label - Model Info, Sticker
Vintage style model information label. This label has a line for a model name or number, the serial number, builder name or company, and the build date. This sticker is a great way to provide build info with a professional presentation on the chassis of a pedal or amp.
$0.95
On Backorder
Label - Danger High Voltage, Small, Sticker
Package of 4
Danger high voltage label for amplifiers and other equipment. These stickers are a great option for labeling equipment and builds as high voltage whenever necessary. The sticker is a single piece that must be cut to size using scissors or a paper cutter to make a total of four labels. This style of label is perfect for smaller areas like circuit boards, components, heatsinks and other areas inside the chassis.
$1.25
Finishing Washer - #4, Countersunk
Package of 10
#4 finishing washers. Designed for accommodating the heads of countersunk screws. It provides additional bearing area on the material being fastened and can be used to give a neat, finished appearance.
Starting at $1.35
Battery Holder with Connector - 9V, Chassis Mount, Horizontal
High quality chassis mount battery holder with a built-in connector. This clip fits standard 9V batteries. The horizontal mount and small footprint of the holder allows for easy placement where vertical space is limited. The two connections use individual solder tabs for hard wiring directly into projects providing a rugged and stable connection.
$5.45
Soldering Iron Tip - Atten, Hoof, T900
Atten T900 soldering iron tips. The hoof style is great for soldering through hole components and many other situations such as SMD soldering. The flatted cylindrical tip is perfect for drag soldering surface mount components. These tips are an excellent choice for use with the S-ST-2090D soldering station and S-ST-2065D soldering iron.
Starting at $2.35
Bench-top Smoke Absorber - Atten, ST-1016, For Soldering
Atten ST-1016 benchtop fume extractor with LED light. This smoke absorber can be operated vertically or horizontally for more focused extraction based on positioning. The filter is made of highly activated carbon for better absorption. The fan provides a steady pull ensuring that all fumes pass through the filter when used properly. The optional light can provide additional lighting on the soldering surface. Carbon filter included. Specifications:
  • Air volume (vertical): 1.03 m³/min
  • Air volume (horizontal): 0.4 m³/min0.4
  • Air flow (vertical): 1.0 m/s
  • Air flow (horizontal): 2.6 m/s
$49.95