New Products

15° sloped aluminum consoles from Hammond’s 1456 Series with wood sides. These enclosures are a great choice for desktop effects and synthesizers as well as vintage style stompboxes. Features:

• 4" x 5.5" x 2" (1” height at front)
• Top panels are 0.064” thick aluminum
• Powder coated top and bottom
• Wood sides are real walnut - each piece has a unique color & grain.
• Solid oiled walnut sides on a black, ventilated steel base.
• Comes with self adhesive rubber feet and required mounting hardware.

15° sloped aluminum consoles from Hammond’s 1456 Series. These enclosures are a great choice for desktop effects and synthesizers as well as vintage style stompboxes. Features:

• 4" x 5.5" x 2" (1” height at front)
• Bottom panels are 0.081” (2 mm) thick aluminum
• Top panels are 0.064” thick aluminum
• Fully Powder Coated
• Comes with self adhesive rubber feet and required mounting hardware.

30° sloped aluminum consoles from Hammond’s 1456 Series with wood sides. These enclosures are a great choice for desktop effects and synthesizers as well as vintage style stompboxes. Features:

• 4" x 5.5" x 3" (1” height at front)
• Top panels are 0.064” thick aluminum
• Powder coated top and bottom
• Wood sides are real walnut - each piece has a unique color & grain.
• Solid oiled walnut sides on a black, ventilated steel base.
• Comes with self adhesive rubber feet and required mounting hardware.

30° sloped aluminum consoles from Hammond’s 1456 Series. These enclosures are a great choice for desktop effects and synthesizers as well as vintage style stompboxes. Features:

• 4" x 5.5" x 3" (1” height at front)
• Bottom panels are 0.081” (2 mm) thick aluminum
• Top panels are 0.064” thick aluminum
• Fully Powder Coated
• Comes with self adhesive rubber feet and required mounting hardware.

Phenolic skirted knobs with a set screw and brass insert. These unique knobs closely match the RCA style of knobs used on vintage test equipment, radios, studio consoles and other equipment. They are sometimes referred to as fester knobs. The RCA style knobs feature an inlay indicator line. Fits ¼” (6.35mm) pot shafts. 22mm Skirt:

• Height: 0.495in. (12.6 mm)
• Diameter: 0.875 in. (22 mm)
• Fits ¼" shaft with set screw

26mm Skirt:

• Height: 0.656 in. (16.7 mm)
• Diameter: 1.02 in. (26 mm)
• Fits ¼" shaft with set screw

33mm Skirt:

• Height: 0.792 in. (20.1 mm)
• Diameter: 1.293 in. (33 mm)
• Fits ¼" shaft with set screw

40mm Skirt:

• Height: 0.865 in. (22 mm)
• Diameter: 1.568 in. (40 mm)
• Fits ¼" shaft with set screw

High quality phenolic pointer knob with a vintage design. The retro pointer has a thick band that extends above the base allowing for easy manipulation of the knob making it a great option for rotary controls and switches. This solid phenolic knob has an infilled indicator line with a decorative diamond shaped top. Fits 0.25” (6.35mm) shafts with set screw and brass insert. This knob pairs perfectly with the smaller P-K356 knob.

• Height: 0.85 in.
• Length: 1.63 in.
• Fits ¼" shaft with set screw

Original Marshall™ cabinet logo frame. This mounts to original Marshall™ cabinets using two screws. The adhesive backed badge is then adhered to this frame. Faceplates sold separately.

• Fits 1960 cabinets
• Black plastic
• For 29 x 85mm logos
• Screw mount

Phenolic skirted knobs with a set screw and brass insert. These fluted round knobs are close matches for the classic knobs used on Orange Amps. Each knob features a painted dot indicator on the skirt. Fits ¼” (6.35mm) pot shafts. 19mm Skirt:

• Height: 0.61 in. (15.5 mm)
• Diameter: 0.74 in. (19 mm)
• Fits ¼" shaft with set screw

28mm Skirt:

• Height: 0.61 in. (15.5 mm)
• Diameter: 1.1 in. (28 mm)
• Fits ¼" shaft with set screw

42mm Skirt:

• Height: 0.79 in. (20 mm)
• Diameter: 1.645 in. (42 mm)
• Fits ¼" shaft with set screw

High quality chicken head style knob with a unique angular design. The stealth chicken head has a thin band that extends above the base allowing for easy manipulation of the knob. This solid phenolic knob has an infilled indicator line. Fits 0.25” (6.35mm) shafts with set screw and brass insert.

• Height: 0.7 in.
• Length: 1.408 in.
• Fits ¼" shaft with set screw

1N60 point-contact germanium diodes in a DO-7 package with striped clear glass. 1N60 diodes were used in many vintage electronics and also make for great clipping diodes in stompbox effects pedals.

IC-LOC™ Green is a thin, medium-high strength threadlock that is applied to fasteners that are already assembled. IC-LOC™ Green wicks down into the threads of fasteners using capillary action and has good performance even with oil coated fasteners. Uses

• Threads of fasteners
• Bolts
• Screws
• Nuts

Directions: Shake well. Unscrew cap and cut off tip. Apply IC-LOC™ Green to clean preassembled fasteners. Product sets in 10 minutes, with full cure within 24 hours. IC-LOC™ Green prevents the loosening of threaded fasteners from shock and vibration by wicking into threads. Cured temperature range is -60° to +300°F (-51° to +149°C). Locked fasteners are only removable by localized heating and hand tools. Remove residue with a damp cloth. Similar to Loctite Green.

Potentiometer cleaning caps for use with aerosol cleaners such as DeoxIT. This is a great tool for difficult to clean potentiometers such as those on hollow body guitars and certain amp chassis. The design pushes the spray in through the bushing of the potentiometer removing the need to access the back of the potentiometer. To use: Remove the knob and thread the cleaning cap onto the potentiometer. If there is enough bushing, attach the rubber o-ring first. If not, simply thread the cleaning cap onto the bushing and place a rag around it. Using a rag is recommended with and without the o-ring. Insert the DeoxIT straw into the small hole on the side of the cleaning cap. Cover the open end with your finger and spray. The cleaning solution is directed to the shaft of the pot where it can seep in. You can turn split shaft pots with a screwdriver through the open end to help move the cleaner around inside the pot.

PCBs with similar styling to the eyelet/fiberboard used in vintage equipment. The spacing between pads is 7.5mm horizontally and 26mm vertically.

This PCB is a recreation of the iss. 1 circuit board found in classic Fuzz Face pedals. When drawing the layout, multiple originals were closely referenced to ensure a proper match and fit. The copper traces are gold plated providing protection from corrosion indefinitely. This classic board fits the mounting holes on both original and reproduction Fuzz Face enclosures. There are numerous great parts choices available for this PCB.

This board is a recreation of the MKI circuit board found in early Tone Bender pedals. When drawing the layout, an original board was closely referenced to ensure a proper match and fit. Since the MKI boards were hand drilled, the holes have an organic layout that was somewhat unique to each build. This board follows the exact hole pattern of one of these original builds. The build style is also fairly unique in the MK1. It is a point to point style board without eyelets or turrets. The leads of the parts are wrapped upward around the edge of the board and then solder is applied to connect the components. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below. There are numerous great parts choices available for this PCB.

PCBs with similar styling to the eyelet/fiberboard used in vintage equipment. The spacing between pads is 9.1mm horizontally and 34.4mm vertically. The two mounting holes have a 3.2mm diameter to fit M3 or 4-40 hardware and also fit the S-H190 adhesive standoffs perfectly. See P-HTB-X for 7.5mm spacing 2x8 Board:

• 2 rows of 8 eyelets (16 total)
• 9.1mm x 34.4mm eyelet spacing
• 69.42mm x 40.1mm board
• 54.6mm spacing for 3.2mm mounting holes
• Great fit for 1590P1, Gorva S90, and YY slanted enclosures

2x10 Board:

• 2 rows of 10 eyelets (20 total)
• 9.1mm x 34.4mm eyelet spacing
• 87.1mm x 40.1mm board
• 72.8mm spacing for 3.2mm mounting holes
• Great fit for 1590BB enclosures

This board is a recreation of the circuit board found in Tone Bender Professional MKII pedals. When drawing the layout, an original board was closely referenced to ensure a proper match and fit. Since the MKII boards were cut from stripboard, this board follows the same format but is completely ready for soldering with precut traces and drilled mounting holes. The build style is very straightforward on the Mk2. It is a standard stripboard build and follows a very linear circuit path across the board. The traces are gold plated making soldering easier than most stripboards. Additionally the plating provides protection from corrosion. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below. There are numerous great parts choices available for this PCB.

Premium 9V battery clip made of a rigid plastic frame with an insulating wall enclosing the battery terminals. This high quality battery snap features nickel-plated brass contacts. The six inch leads are 26 AWG stranded wire, prestripped and tinned for an easy installation.

3PDT switch mounted charge pump PCB for positive ground effects. This small PCB simplifies the wiring of 3PDT foot switches in guitar pedals while also offering -9V when used with a standard +9V power supply. This is a great option for positive ground effects such as vintage fuzz pedals. The circuit of this PCB also features a protection diode and an LED indicator for when the effect is engaged.
This board is compatible with the MAX1044, TC1044S, TC7660S, and LT1054 charge pump ICs.

Screw mounted charge pump PCB for positive ground effects. This small PCB provides -9V when used with a standard +9V power supply. This is a great option for positive ground effects such as vintage fuzz pedals. The PCB has a low profile design and is a simple addition to any build using a standoff to mount the board. This board is compatible with the MAX1044, TC1044S, TC7660S, and LT1054 charge pump ICs.

Single row turret strips with a tab for mounting directly to tube socket mounting holes. The screw mount turrets are made of gold plated brass and are pre-mounted to the 2mm thick boards. The mounting hole is 0.15” in diameter. These turret strips are a great option for components connecting to the socket lugs of point to point builds.

High quality manila paper tags. These tags are pre-strung with a soft string gentle enough to use on the most delicate equipment. The paper is heavy duty 13 point stock and the ¼” eyelet is reinforced to resist tearing. These are great tags for pricing, labeling, and cataloging equipment.

CE Manufacturing USA Made Multi Section Can Capacitor. Reproduced To Exact Mallory Specs Using Original Mallory Machinery.

• 150/80/80/50 250VDC.
• FP / Twist Lock Style. Solder Tabs.
• -10%, +50% Tolerance, 85°C Temperature Rating.
• 1 ⅜"D X 3"H.

All CE Manufacturing can capacitors have a two year warranty against manufacturer defects.

IC component sockets for dual in-line package chips (DIP, PDIP, DIL, DIPP.) These sockets feature ladder style cases with tinned stamped and formed connections.