New Products

Op-Amp - TL071, Single, Low-Noise, JFET-input, 8-Pin DIP
TL071 single op amp in an 8-pin DIP package. The TL07xx JFET-input operational amplifier family is designed to offer a wider selection than any previously developed operational amplifier family. Each of these JFET-input operational amplifiers incorporates well-matched, high-voltage JFET and bipolar transistors in a monolithic integrated circuit. The devices feature high slew rates, low-input bias and offset currents, and low offset-voltage temperature coefficient. The low harmonic distortion and low noise make the TL07xseries ideally suited for high-fidelity and audio pre-amplifier applications.
$0.82
Nut - Mod® "Top Brass", for Qingpu and other 3.5mm jacks
Mod® "Top Brass" nuts are the easiest way to upgrade your Eurorack module or other 3.5 mm application to a more regal look - we call it "Top Brass". Designed with the same outer dimensions as Qingpu knurled nuts, these round brass nuts will fit any module using Qingpu or other similar metal-bushing jacks without covering up the jack labels. As their name implies, the Mod® "Top Brass" nuts are made out of pure brass, and while they look incredible on their own, their appearance also pairs extremely well with the immersion gold used on Make Noise and other similar modules. Rather than being knurled, Top Brass nuts have a smooth outer edge for a clean look. The nuts are slotted and will work with all existing nut drivers intended for use with the knurled Qingpu-style nuts. "Top Brass" nuts use M6x0.5 threading which matches the bushing on the ubiquitous Qingpu jacks and many of their copies.
$0.30
Header - Round Pin, 20 Position, Breakaway, 2.54mm Spacing
20 position male pin headers with a 2.54mm (0.1”) pitch. These headers use round pins that are smaller than the standard square type and are perfect for use with IC sockets, breadboards, and machine pin sockets. The breakaway construction makes fitting them to projects simple. Features:
  • Round Pin
  • 20 Position
  • 2.54mm Spacing
  • Breakaway
$1.25
Regulator - L78L33, 3.3 Volt, Positive Voltage Regulator, TO-92
L78L33 3.3V regulator in a TO-92 package. The L78L33 three-terminal 3.3V positive regulator employs internal current limiting and thermal shutdown, making them essentially indestructible. If adequate heat-sink is provided, they can deliver up to 100 mA output current. They are intended as fixed voltage regulators in a wide range of applications including local or oncard regulation for elimination of noise and distribution problems associated with single-point regulation. In addition, they can be used with power pass elements to make high-current voltage regulators. The L78L series used as Zener diode/resistor combination replacement, offers e improvement along with lower quiescent current and lower noise. Features:
  • Output voltage of 3.3V
  • Output current up to 100 mA
  • Short-circuit protection
  • No external components are required
$0.50
Crystal - 32.768 kHz, 12.5pF, 3x8mm
Through-hole mount crystal with a 32.768 kHz (32768 Hz) frequency. This crystal has a 12.5pF capacitance and is housed in a 3mm x 8mm package that is commonly used with Spin FV-1 chips. Features:
  • 32.768 kHz Frequency
  • 3x8mm Cylinder Case
  • Through Hole
  • 12.5pF
$0.29
Knob - Davies, 1550, Daka-ware, Large, Skirted Pointer
High-quality USA made knobs from Davies Molding. The large skirted 1550 pointer knob is made of solid phenolic and features a white indicator line. The pointer has an overall length of 1.19” and the skirt’s diameter is 1.13”.
  • Height: 0.625 in
  • Length: 1.19 in.
  • Fits ¼" shaft with set screw
$1.75
Knob - Davies, 1914, Daka-ware, Medium, Scalloped Edge
High-quality USA made knobs from Davies Molding. The 1914 knob is the larger version of the classic 1900H found on countless synthesizers and pedals. This knob is made of solid phenolic and features an indicator line on the top. The knob pairs perfectly with the smaller diameter 1900 knobs such as the P-K801-BRASS-X as well as the skirted P-K234X knobs.
  • Height: 0.50 in.
  • Diameter: 0.75 in.
  • Fits ¼" shaft with set screw
$3.55
Switch - Toggle, DPST, On-Off, Chrome Tip
Toggle switch for Marshall amps, latching 2 position DPST, On-Off. 15A 250VAC rating. Used for Mains and Standby switch in Marshall 1959SLP, 1987X, 2245 and others. Mounting nuts (1 hex and 1 knurled) included. Main features:
  • Construction : Terminal and contact support are manufactured from a single piece of metal. The contacts are resistance-welded to the terminal for increased mechanical strength.
  • Rating : These switches are suitable for motor loads and power applications up to 15A 250VAC
  • UL, CSA and NF-VDE (EN 61058-1) approved

Note: On-Off switches may sometimes be referred to as On-None-Off.
$13.95
Cloth Pedal Bag - 4” x 6”, 100% Cotton
Keep your pedals pristine with these 100% cotton bags. These drawstring bags are 4 in. x 6 in. and fit 1590B or smaller stompboxes. Cloth pedal bags are also great packaging for boutique pedal builders.
$0.75
Cloth Pedal Bag - 3” x 5”, 100% Cotton
Keep your pedals pristine with these 100% cotton bags. These drawstring bags are 3 in. x 5 in. and fit 1590A stompboxes. Cloth pedal bags are also great packaging for boutique pedal builders.
$0.65
Pedal Box - 12” x 5” x 4", Fits Wah Pedals and Loopers
High quality crush-proof boxes that are perfectly sized for larger stompboxes. This cardboard box features triple wall sides and double wall front and bottom ensuring a safe housing for your pedals. The inside dimensions 12” x 5” x 4" fit wah pedals, 1032L (looper enclosure), and other large pedals along with accessories such as power supplies or cables. These boxes are ideal for storing or packaging effects pedals.
$2.59
Chassis Box - Hammond, 1590P1, Diecast, 6.02” x 3.27” x 1.98”
Large 6.02” x 3.27” x 1.98” Hammond 1590P1 enclosures. This enclosure is a great option for dense builds and is a popular choice for vintage style fuzz pedals with plenty of room for point to point wiring.
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
  • Dimensions shown are exterior dimensions.
  • Add 0.16" to enclosure depth for lid.
$13.50
Knob - Davies, 1910 and 1913, Daka-ware, Skirted
High-quality USA made knobs from Davies Molding. The skirted 1900 series knobs are made of solid phenolic and feature an indicator line on the skirt. These classic knobs have been used on a variety of equipment throughout the decades and are still popularly used on synthesizers today. The smaller 1910 knob was used on many early Serge paperface panels. Davies 1910 (Small)
  • Height: 0.50 in.
  • Diameter: 0.75 in.
  • Fits ¼" shaft with set screw

Davies 1913 (Large)
  • Height: 0.625 in.
  • Diameter: 1.13 in.
  • Fits ¼" shaft with set screw
$2.75
Transistor - 2N5135, Silicon, TO-105 case, NPN
The 2N5135 is a silicon NPN transistor in a TO-105 case. This transistor is a close match to the rare 2N5133 but with higher voltage ratings and is in a larger package. The hFE range is less wide than the 2N5133 with more values in the range found in the batches used on vintage Big Muff pedals. The lower hFE range also makes these a great option for silicon fuzz pedals.
$1.75
Wood Tack - Screw Nail, Steel, 20mm
Steel 20mm screw nails for corners, logos, badges, and more. These screw nails make adding cabinet accessories easy requiring only a mallet for installation. The design is great for speaker cabinets ensuring a better grip than standard nails and tacks under extreme vibrations.
$0.35
Switch - Rocker, Round Mounting Hole, SPST, 6A, 125VAC
Rectangular rocker switch that uses a round mounting hole. This black nylon rocker switch has a small panel footprint and is easy to add to projects due to the round mounting hole. Mounting nut and lock washer included.
  • SPST
  • On-Off
  • 6A, 125VAC / 3A, 250VAC
  • 12.2mm Mounting Hole
$1.95
Knob - Davies, 1470, Daka-ware, Large, Pointer
Colors Available:
High-quality USA made knobs from Davies Molding. The large 1470 pointer knob is made of solid phenolic and features a fine ridged grip with a distinctive point. This classic knob has been used on a variety of guitar pedals such as the Klon and countless EHX effects.
  • Height: 0.50 in.
  • Length: 1.13 in.
  • Fits ¼" shaft with set screw
Starting at $1.95
Trimmer - Piher, Single Turn, Top Adjust, Horizontal PCB Mount, 25kΩ
25kΩ Piher PT-15 15mm carbon trimmer potentiometers. These trimmers are used in a variety of amps and equipment and mount horizontally to the PCB with a slotted top adjustment. Features:
  • Carbon resistive element
  • Dust proof enclosure
  • Polyester substrate
$1.39
Knob - Phenolic, Set Screw, Gaunt Chicken Head
High quality chicken head knobs with vintage gaunt design. The gaunt chicken head has a thinner band that extends above the base allowing for easy manipulation of the knob. This knob has a thick infilled indicator line and is made of solid phenolic. Fits 0.25” (6.35mm) shafts with set screw and brass insert.
  • Height: 0.67 in.
  • Length: 1.26 in.
  • Fits ¼" shaft with set screw
$1.15
Knob - Davies, 8005 & 8010, Daka-ware, Vintage Pointer
High-quality USA made knobs from Davies Molding. The 8000 series knobs are made of solid phenolic and feature a classic teardrop design. The detailed design makes these knobs a striking addition to any piece of equipment. This unique design has been used on a variety of tools and instruments. Davies 8005 (Small)
  • Height: 0.78 in.
  • Length: 1.05 in.
  • Fits ¼" shaft with set screw

Davies 8010 (Large)
  • Height: 1 in.
  • Length: 1.25 in.
  • Fits ¼" shaft with set screw
$3.95
Regulator - LT1054, Voltage Converter w/ Regulator, 8-Pin DIP
LT1054 switched-capacitor voltage converter with regulator in an 8 pin DIP package. The LT1054 device is a bipolar, switched-capacitor voltage converter with regulator. It provides higher output current and significantly lower voltage losses than previously available converters. An adaptive-switch drive scheme optimizes efficiency over a wide range of output currents. Total voltage drop at 100-mA output current typically is 1.1 V. This applies to the full supply-voltage range of 3.5 V to 15 V. Quiescent current typically is 2.5 mA. The LT1054 also provides regulation, a feature previously not available in switched-capacitor voltage converters. By adding an external resistive divider, a regulated output can be obtained. This output is regulated against changes in both input voltage and output current. The LT1054 can also shut down by grounding the feedback terminal.
$2.25
Dial Plate - 0 to 100, Black on Brushed Metal
Dial plates with 0-100 indicator marks. These plates are a simple way to add panel graphics to controls. They are easy to install beneath the nut of a potentiometer like a washer. The silk screened graphics on the brushed metal plate gives projects a clean and professional appearance. 40mm Dial Plate
  • 40 mm (1.575”) outer diameter
  • 9.95 mm (0.392”) inner diameter
  • Best for 25.4mm (1”) or smaller knobs

60mm Dial Plate
  • 60mm (2.362”) outer diameter
  • 9.95mm (0.392”) inner diameter
  • Best for 40.6 mm (1.59”) or smaller knobs
$1.65
Terminal Strip - Barrier Strip, 5 Pole, Dual Lugs
High quality 5 pole dual barrier strip. These terminal blocks have a solid PBT base with plated brass terminals and combination head screws. Features:
  • PBT Base
  • Closed Back Design
  • Combo Phil-Slot Nickel-plated Steel Screws
  • Plated Brass Terminals
  • 5 Poles
  • 10 Lugs
  • 57.2mm Mounting Centers
  • UL 94V-0
$2.75
Knob - Aluminum, Set Screw, Diamond Knurl, 0.496” Diameter
Colors Available:
Anodized aluminum knob with channeled indicator line and set screw. This slim, solid aluminum knob has a diamond knurled grip with a diameter of 0.495”. It also features a counterbore which allows it to hide pot bushings for a clean look. Fits ¼” (6.35mm) pot shafts.
  • Height: 0.56 in.
  • Diameter: 0.496 in.
  • Fits ¼" shaft with set screw
$3.50