 | Speaker - Celestion, G12 Neo Creamback, 12"Multiple Options Available The Neo Creamback is every ounce a Classic Celestion, delivering all the magical tone you’d get from a traditional Creamback. The difference is, it’s built with a neodymium magnet: making this speaker around half the weight of a traditional ceramic magnet speaker.Celestion’s engineers have developed a new and innovative way to better harness the mighty forces of the neodymium magnet, enabling us to create a guitar speaker that can deliver authentic Creamback tone with ease, while preserving the benefit of neodymium’s much lighter weight.You still get the low end punch, warm, vocal midrange and sweet refined highs the Creamback is famous for: push it hard and enjoy the ‘race-car growl’ that sets pulses racing.
| $175.00 | Click to read more |
 | Adhesive - Bob Smith Industries, Maxi-Cure Extra Thick CyanoacrylateMultiple Options Available Bob Smith Industries ™ Maxi Cure ™ Extra Thick Gap Filling Cyanoacrylate. A must have for luthiers! Maxi Cure ™ is the highest viscosity CA we have available and is great for extreme gap filling and finish fills. It can be carved with a knife or razor blade and sanded and feathered to form a finish which makes it great for chip repairs. The extra thick viscosity of Maxi Cure ™ also allows longer repositioning time than other glues (10-25 sec.) Apply Maxi Cure ™ in a coil pattern to one of the parts to be glued, spread glue evenly, then assemble parts. Hold or clamp firmly for 30-60 seconds. To speed up curing time use the Insta-Set accelerator! (S-F506)
- Extra thick, gap filling consistency
- 10-25 second cure time
- For looser fitting applications where a low viscosity glue is required
- Available in 1oz. and 2oz. sizes
WARNING*: These products are eye and respiratory irritants. Product can bond skin instantly.
| Starting at $5.50 | Click to read more |
 | Adhesive - Bob Smith Industries, Insta-Cure + Gap FillingMultiple Options Available Bob Smith Industries™ Insta-Cure+™ Medium Gap Filling Cyanoacrylate. A must have for luthiers! Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps or the parts to be glued don’t fit perfectly. Medium viscosity super glue is the most common glue used in many luthiery applications due to it’s cure time and viscosity. Recommended for binding repair and small poly finish touch ups. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. To speed up curing time use the Insta-Set accelerator!
| Starting at $5.50 | Click to read more |
 | BreadBoard - Solderless, 400 point patternSolderless (plug-in) breadboard with 400 connection tie-points (i.e. 400 wire insertion holes) and 4 power rails. Solderless breadboards are great for building and testing new circuits because parts can be easily inserted and removed making them completely re-usable. This breadboard has a 300 tie-point IC-circuit area plus four 25 tie-point power rails. The housing is made of white ABS plastic, with a printed legend giving numbers and letters for columns and rows. The internal contacts are phosphor bronze with a plated nickel finish and a peelable adhesive tape backing is provided for attaching it to a surface. Be sure to check out the Zipwire™ jumper wire kits for use with this breadboard.
| $4.75 | Click to read more |
 | BreadBoard - Solderable PCB, 400 point pattern Solderable PC BreadBoard enables you to transfer your circuit and wires from a plug-in breadboard without recutting wires or changing your layout. This breadboard has the same pattern as a standard 400 connection point solderless plug-in breadboard which has a standard 5-hole strip for each IC pin, just like solderless breadboards. However, it has the advantage that soldered joints provide a more reliable long-term connection than solderless contacts.
The board has four power rails like solderless breadboards, plus two bonus rails for power or signals. There are bonus two-hole pads along the centerline allowing DIL (dual in-line) headers to be used as well as a top side silkscreen to position components. Four mounting holes allow your projects to be secured. | $4.50 | Click to read more |
 | Adhesive - Bob Smith Industries, Insta-Cure Super ThinMultiple Options Available Bob Smith Industries™ Insta-Cure™ Super Thin Cyanoacrylate. A must have for luthiers! Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds (1-3 sec.). Surfaces to be bonded must be tight fitting (no visible gaps) and should be held together or clamped while you apply the CA around the edges of the seam. For glue applications with small gaps or looser fitting joints the higher viscosity Insta-Cure+™ is recommended.
- Water-thin consistency
- 1-3 second cure time
- For tight fitting applications
- Available in 1oz. and 2oz. sizes
WARNING: These products are eye and respiratory irritants. Product can bond skin instantly. Keep away from children!
| Starting at $5.50 | Click to read more |
 | Jack - Fender, ⅛" Stereo, Phone, for MustangOriginal Fender® 1/8” stereo phone jack . PC mount jack used as Auxiliary and headphone out for Mustang series amps.
| $3.25 | Click to read more |
 | Effects Pedal Kit - MOD® Kits, Step Ladder, Input AttenuatorThe Step Ladder is a passive input attenuator using high quality components for excellent reliability. True-bypass mode provides the maximum signal level. The attenuator pot and two toggle switches allow for flexibility in the amount of signal attenuation when not in bypass mode. Treble bleed capacitors in the circuit retain crisp high frequencies even at maximum attenuation. The Step Ladder is ideal for anything from getting a slight boost while playing single-note acoustic guitar leads or for jumping from clean to overdrive in a high-gain electric guitar amp.
| $36.95 | Click to read more |
 | PadBoard - Size 1, Double Sided, Plated HolesPrototyping circuit board that has a general purpose pad-per-hole pattern making it great for general purpose analog and digital use. It is a double-sided board with plated holes, which allows components to be easily soldered to either side of the board. A square pad is provided every 5th hole, which makes it easy to align components on the top and bottom of the board. An anti-tarnish coating protects the copper for a long shelf-life and provides easy soldering.
For fastening your project to a surface see our adhesive standoffs (S-H190-X)
Features:
- Pad-per-hole prototyping board with plated-thru holes. A square pad every 5th hole makes it easy to align components on top and bottom.
- Double-sided high-quality FR4 glass-epoxy circuit board with plated holes. Components can be soldered to either side.
- 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
- 31 x 19 holes, 0.037" holes are drilled on 0.1" (2.54mm) centers. Four 0.125” mounting holes.
- Size 1 = 1.97 x 3.15in (50 x 80mm), 1/16" thick (1.6mm)
| $2.95 | Click to read more |
 | Multi-Tool - CruzTOOLS GrooveTech, for Guitar and BassIntroducing the second generation of the GrooveTech Guitar/Bass Multi-Tool Introduced in 2008, the original GrooveTech Multi-Tool was an instant hit with guitar and bass players alike. Never before had a multi-tool provided such functionality or made use of pro-grade components. In spite of market acceptance, CruzTOOLS designers envisioned improvements and spent over two years developing a second generation tool that boasts significant advances. Like the original tool, both inch and metric hex wrenches are provided with ball-ends for truss rod sizes. Tool components use professional S2 steel with an attractive polished-chrome finish. Second-generation improvements include a 5/16" socket for Gibson and similar truss rod nuts, addition of 5mm and 1/16" hex wrenches, and a precision ruler with inch and metric scales.
| $15.95 | Click to read more |
480.820.5411