You are here

Pedal Parts / DIY

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(34 pages)
P-H1590B3Chassis Box - Hammond, 1590B3, Diecast, 4.6" x 3.0" x 1.5"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
  • Dimensions shown are exterior dimensions.
  • Add 0.16" to enclosure depth for lid.

$8.90
Click to read more
P-H1590BB2Chassis Box - Hammond, 1590BB2, Diecast, 4.7" x 3.7" x 1.5"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
  • Dimensions shown are exterior dimensions.
  • Add 0.16" to enclosure depth for lid.

$10.12
Click to read more
P-H1590G2Chassis Box - 1590G2, Diecast, 3.9" x 2.0" x 1.2"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
  • Dimensions shown are exterior dimensions.
  • Add 0.16" to enclosure depth for lid.

$7.95
Click to read more
P-H544Switch - Carling, Mini Toggle, SPDT, On-On, PC Mount, right angle

Genuine Carling 2 Position Mini Toggle, On-On, Short Round Bat, Right Angle, PC Mount Features:



  • SPDT ( Single Pole/ Double Throw) On-On switch
  • 0.275" bushing length
  • 0.270” bat length
  • ¼" chassis hole diameter
  • Right angle, PC Mount terminals


Note: On-On switches may sometimes be referred to as On-None-On.


$2.50
Click to read more
S-H960Bezel - Cliff, Black for S4 Jack Socket

Genuine Cliff™ replacement bezel for S4 Series jacks. These can be used with any of our Cliff™ jacks using the metal ferrule style nut. Sold individually.


$0.20
Click to read more
P-QLM386N1Audio Power Amplifier - LM386N-1, Low Voltage

LM386 Low Voltage Audio Power Amplifier The LM386 is a mono low voltage amplifier that can be used in a variety of applications. It can drive loads from 4 Ω to 32 Ω. The gain is internally set to 20 but it can be modified from 20 to 200 by placing a resistor and capacitor between pins 1 and 8. As this is an Op Amp it can be used in different configurations to fit in several applications. The internal gain setting resistor allows the LM386 to be used in a very low part count system. In addition a series resistor can be placed between pins 1 and 5 to modify the gain and frequency response for specific applications. These are found in many small audio amplifiers and even tiny pedal sized guitar amplifiers! There are tons of possibilities for this little Op Amp.


$1.25
Click to read more
S-H961Bezel / Nut - Cliff, For S4, Combined Nut / Bezel, Black

Genuine Cliff™ replacement combination nut/bezel for S4 Series jacks.



  • 3/8” thread diameter/20 TPI
  • 3/16” thread length
  • 7/16” nut
  • Used on many Marshall amps
  • Matte black finish
  • Sold individually.

$0.45
Click to read more
P-RBTSE-99FXDSP Module - Accutronics, 99 Effects (Reverb, Chorus, Delay, +)

The BTSE-99FX Effect board provides 99 different digital audio effects to be used in many audio applications that require sound enhancement. Equipped with a superb quality digital effects processing engine which adds that extra punch needed to make sounds truly stand out. Applications:



  • Guitar/ Keyboard/Bass amplifiers and combos
  • Audio mixing consoles / Powered mixing consoles
  • Stand -alone stereo effect units for studio and PA usage
  • Effects pedals

$32.00
Click to read more
P-H542XSwitch - Carling, Mini Toggle, DPDT, 3 Position

Genuine Carling DPDT 3 Position Mini Toggle, Round Bat, Solder Lugs



  • DPDT ( Double Pole/ Double Throw) switch
  • 0.354" bushing length
  • 0.409” bat length
  • ¼" chassis hole diameter
  • Solder terminals

Starting at $3.10
Click to read more
R-NResistors - ¼ Watt, Metal Film, 1% tolerance
Package of 5

Metal Film resistors consist of a resistive element of an extremely thin layer of metal alloy vacuum deposited on a substrate. Precise and quiet. Package of 5. These resistors are perfect for pedal builders! 1/4 watt.


$1.80
Click to read more

Pages

(34 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Pedal Parts / DIY