Pedal Parts / DIY

Original Dunlop offset grommets (i.e. rubber bumpers) used on the underside of the treadle piece (rocking structure) of wah pedal enclosures. Made in USA.

PCB Mount stereo jacks with a very low profile. These jacks have a smaller footprint than the Lumberg jacks that are popular for tight pedal builds. They are perfect for top mounted jack pedal builds and any other project where space is limited. Mounting nut and flat washer included.

• M9*0.75 Bushing Thread
• Stereo 3-Conductor (TRS)
• Open Circuit (does not have switched terminal).
• Includes nut and washer.

This jack can be found in many modern versions of the classic Boss pedals such as the DS-1 and SD-1.

LM380 power amp in a 14-pin DIP package. The LM380 is a power audio amplifier for consumer applications. In order to hold system cost to a minimum, gain is internally fixed at 34 dB. A unique input stage allows ground referenced input signals. The output automatically self-centers to one-half the supply voltage. The output is short circuit proof with internal thermal limiting. The package outline is standard dual-in-line. The LM380N uses a copper lead frame. The center three pins on either side comprise a heat sink.

Dual low power opamps in an 8-pin DIP package. The TL062 offers a high input impedance and 1MHz bandwidth.

1N5408 Diode. Lead mounted standard recovery rectifiers are designed for use in power supplies and other applications having need of a device with the following features:

• High Current to Small Size
• High Surge Current Capability
• Low Forward Voltage Drop

The CD4013B device consists of two identical, independent data-type flip-flops. Each flip-flop has independent data, set, reset, and clock inputs and Q and Q outputs. These devices can be used for shift register applications, and, by connecting Q output to the data input, for counter and toggle applications. The logic level present at the D input is transferred to the Q output during the positive-going transition of the clock pulse.

High-quality USA made knobs from Davies Molding. The small skirted 1610 knob is made of solid phenolic and features an indicator line on the 0.91” diameter skirt. This classic knob has been used on a variety of equipment and most notably on the Buchla 100 Series as well as some 200 Series modules.

• Height: 0.59 in.
• Diameter: 0.91 in.
• Fits ¼" shaft with set screw

The large skirted 1600 knob is made of phenolic and features an indicator line on the 1.5” diameter skirt. This classic knob has been used on a variety of equipment and most notably on the Buchla 100 Series as well as some 200 Series modules.

• Height: 0.69 in.
• Diameter: 1.5 in.
• Fits ¼" shaft with set screw

Large skirted aluminum knob with indicator line and set screw. This solid aluminum knob has a 1.125 in. diameter skirt and ¾” grip that features a minimalistic style of fluting. The knob uses dual set screws to ensure no slipping once set on the pot’s shaft. Fits ¼” (6.35mm) pot shafts.

600V stranded. Strands are tinned individually. See photos for detail. UL style 1015, rated to 105 degrees C. Perfect for new projects or rewiring any electrical equipment.

Solder terminals, non-switched. Metal ferrule, vintage style found in many amplifiers and pedals. For the switched version, see S-H901-X. Features:

• Low-noise Ni-Ag® Alloy Self-Cleaning Contacts for superior performance and reliability
• Tough, molded grade 1 black Nylon body.
• Made in the U.K.
• Supplied with a metal hexagonal mounting nut
• Designed to receive both mono and stereo ¼" jack plugs
• Withstand Voltage: 2000VDC Min.
• Maximum Current: 5A
• Temperature Rating: -10°C ~ +70°C
• Life (Minimum): 10,000+ Operations
• Nominal Contact Resistance: < 50 mΩ

The 2N5135 is a silicon NPN transistor in a TO-105 case. This transistor is a close match to the rare 2N5133 but with higher voltage ratings and is in a larger package. The hFE range is less wide than the 2N5133 with more values in the range found in the batches used on vintage Big Muff pedals. The lower hFE range also makes these a great option for silicon fuzz pedals.

Lumberg panel mount barrel jack with solder lugs.This DC jack features a normally closed switch on the ring (sleeve) connection. For use with barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Mounting nut included.

Dual 9 volt battery box. Two 9V battery compartments, each compartment having its own red and black wires for battery positive and negative connections (4 wires total) allowing for series, parallel or separate connections of two 9V batteries. Four wood screws included. Directions: 1. Refer to the Drawing B and make a hole on guitar body. 57.5 mm (2.26") x 49.5 mm (1.95"), R6 (6 mm = 0.24") 2. Put the box in guitar body and fix it by screws.

Anodized aluminum knob with short indicator line, set screw, and a matte metal finish. This solid aluminum knob has a straight knurled grip with a diameter of 0.5”. The knob also features a counterbore which allows it to hide pot bushings for a clean look. Fits ¼” (6.35mm) pot shafts. For a larger version of this knob, see P-K611-X. For a brushed finish version of this knob, see P-K655X.

Padboard featuring a 0.15” vintage spacing. This spacing is great for vintage-style builds and more easily accommodates axial capacitors and other larger sized vintage parts like resistors and transistors. The board has a 20x10 grid of pads and easily fits into 1590BB style enclosures and larger vintage-style fuzz enclosures. Each square pad is HASL coated making soldering easier than most protoboards and also ensures a long shelf life. Features:

• High-quality 1.6mm FR4 glass-epoxy circuit board
• 1oz/ft2 copper weight
• HASL coated square shaped pads
• 20 x 10 holes
• 3.04” x 1.55”

Metal Film resistors consist of a resistive element of an extremely thin layer of metal alloy vacuum deposited on a substrate. Precise and quiet. Package of 5. These resistors are perfect for pedal builders! 1/4 watt.

Carling SPST latching On-Off footswitch. Used in Fender etc. Reverb/tremolo/channel switching pedals, (110-P).

9V battery clip with a fiberboard frame. This high quality battery snap features tinned brass eyelets that secure the nickel-plated steel contacts to the fiberboard. Wires can be soldered directly to the eyelets allowing for custom length battery connections. This fiberboard style is similar to the 9V battery connectors in vintage electronics such as the Arbiter Fuzz Face.

High-quality USA made knobs from Rogan Corp. These medium knobs feature a metal insert, spun aluminum inlay, and a skirt with an infilled arrow indicator. The RB-67 Series from Rogan is popularly used on Buchla 200 Series modular synthesizers and can be found on many contemporary eurorack synthesizers..

• Height: 0.77 in.
• Diameter: 1.15 in.
• Fits ¼" shaft with set screws

A variety of sizes and colors are available from the RB-67 Series. See the links below for the full selection of knobs from this series. P-K770-X Small P-K770S-X Small Skirted P-K771S-X Medium Skirted P-K772S-B Large Skirted

Carling mini-toggle switch, SPDT, Solder Lug, 3-Position, On/Off/On

Fender R/A 1/4" mono jack. Used 1999-present. Hex nuts not included (S-H510).

Polyester Film Capacitor used in MOD® Pedal Kits. Rated at 0.1µF 50V. Tolerance: 10%. Operating temperature: -40 C to +85 C

Stripboard made with a phenolic substrate. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This stripboard features standard 0.1” (2.54mm) spacing. The board has a 30x15 grid (15 strips) and easily fits into 1590BB style enclosures and larger vintage-style fuzz enclosures. Each strip is gold coated making soldering easier than most protoboards and also ensures a long shelf life. Features:

• High-quality 1.6mm phenolic circuit board
• Gold coated strips
• 30 x 15 holes (15 strips)
• 3.04” x 1.55”

2N404 PNP germanium transistors. The 2N404 is used in many fuzz pedals along with other effects. This transistor is in a TO-5 package with long leads commonly found on germanium transistors. For a higher voltage version of this transistor, see P-Q2N404A.