# Pedal Parts / DIY

Regulator - TC1044, Charge Pump DC-TO-DC Voltage Converter, 8-Pin DIP
TC1044 charge pump voltage converter in an 8 pin DIP package. The TC1044S is a pin-compatible upgrade to the Industry standard TC7660 charge pump voltage converter. It converts a +1.5V to +12V input to a corresponding –1.5V to –12V output using only two low cost capacitors, eliminating inductors and their associated cost, size and EMI. Added features include an extended supply range to 12V, and a frequency boost pin for higher operating frequency, allowing the use of smaller external capacitors. The on-board oscillator operates at a nominal frequency of 10kHz. Frequency is increased to 45kHz when pin 1 is connected to V+.
$2.15 Op-Amp - TL071, Single, Low-Noise, JFET-input, 8-Pin DIP TL071 single op amp in an 8-pin DIP package. The TL07xx JFET-input operational amplifier family is designed to offer a wider selection than any previously developed operational amplifier family. Each of these JFET-input operational amplifiers incorporates well-matched, high-voltage JFET and bipolar transistors in a monolithic integrated circuit. The devices feature high slew rates, low-input bias and offset currents, and low offset-voltage temperature coefficient. The low harmonic distortion and low noise make the TL07xseries ideally suited for high-fidelity and audio pre-amplifier applications.$0.82
Integrated Circuit - 24LC32A/P, EEPROM, 8-pin DIP
24LC32A/P EEPROM in an 8-pin DIP package commonly used in Spin FV-1 projects. The Microchip Technology Inc. 24LC32A is a 4K x 8 (32K bit) Serial Electrically Erasable PROM capable of operation across a broad voltage range (2.5V to 6.0V). It has been developed for advanced, low power applications such as personal communications or data acquisition. The 24LC32A also has a page-write capability of up to 32 bytes of data. The 24LC32A is capable of both random and sequential reads up to the 32K boundary. Functional address lines allow up to eight 24LC32A devices on the same bus, for up to 256K bits address space. Advanced CMOS technology and broad voltage range make this device ideal for low-power/low-voltage, nonvolatile code and data applications.
$1.15 Regulator - LT1054, Voltage Converter w/ Regulator, 8-Pin DIP LT1054 switched-capacitor voltage converter with regulator in an 8 pin DIP package. The LT1054 device is a bipolar, switched-capacitor voltage converter with regulator. It provides higher output current and significantly lower voltage losses than previously available converters. An adaptive-switch drive scheme optimizes efficiency over a wide range of output currents. Total voltage drop at 100-mA output current typically is 1.1 V. This applies to the full supply-voltage range of 3.5 V to 15 V. Quiescent current typically is 2.5 mA. The LT1054 also provides regulation, a feature previously not available in switched-capacitor voltage converters. By adding an external resistive divider, a regulated output can be obtained. This output is regulated against changes in both input voltage and output current. The LT1054 can also shut down by grounding the feedback terminal.$2.25
Op-Amp - LF347, Quad, Wide Bandwidth, 14-Pin DIP
LF347 quad op amp in a 14-pin DIP package. The LF347 is a low cost, high speed quad JFET input operational amplifier with an internally trimmed input offset voltage ( BI-FET II™ technology). The device requires a low supply current and yet maintains a large gain bandwidth product and a fast slew rate. In addition, well matched high voltage JFET input devices provide very low input bias and offset currents. The LF347 is pin compatible with the standard LM348. This feature allows designers to immediately upgrade the overall performance of existing LF348 and LM324 designs. The LF347 may be used in applications such as high speed integrators, fast D/A converters, sample-and-hold circuits and many other circuits requiring low input offset voltage, low input bias current, high input impedance, high slew rate and wide bandwidth.
$0.69 Op-Amp - AS301AN, Alfa, Single, 8-Pin DIP The AS301AN is Alfa’s version of the LM301A in an 8 pin DIP package. The AS301A is a general purpose operational amplifier. This amplifier offers many features which make its application nearly foolproof: overload protection on the input and output, no latch-up when the common mode range is exceeded, and freedom from oscillations and compensation with a single 30 pF capacitor. It has advantages over internally compensated amplifiers in that the frequency compensation can be tailored to the particular application. For example, in low frequency circuits it can be overcompensated for increased stability margin. Or the compensation can be optimized to give more than a factor of ten improvements in high frequency performance for most applications. In addition, the device provides better accuracy and lower noise in high impedance circuitry.$1.95
Op-Amp - AS301AH, Alfa, Single, TO5-8 case
The AS301AH is Alfa’s version of the LM301A in an 8 pin TO5 package. The AS301A is a general purpose operational amplifier. This amplifier offers many features which make its application nearly foolproof: overload protection on the input and output, no latch-up when the common mode range is exceeded, and freedom from oscillations and compensation with a single 30 pF capacitor. It has advantages over internally compensated amplifiers in that the frequency compensation can be tailored to the particular application. For example, in low frequency circuits it can be overcompensated for increased stability margin. Or the compensation can be optimized to give more than a factor of ten improvements in high frequency performance for most applications. In addition, the device provides better accuracy and lower noise in high impedance circuitry.
$7.95 Op-Amp - LM1458, Dual, 8-Pin DIP LM1458 dual op amp in an 8-pin DIP package. The LM1458 is a general purpose dual operational amplifier. The two amplifiers share a common bias network and power supply leads. Otherwise, their operation is completely independent. Features • No Frequency Compensation Required • Short-Circuit Protection • Wide Common-Mode and Differential Voltage Ranges • Low-Power Consumption • 8-Lead TO-99 and 8-Lead PDIP • No Latch Up When Input Common Mode Range is Exceeded$1.15
Op-Amp - NE5532, Dual, Low Noise, Audio, 8-Pin DIP
NE5532 dual op amp in an 8-pin DIP package. The NE5532 device is a high-performance operational amplifier combining excellent DC and AC characteristics. They feature very low noise, high output-drive capability, high unity-gain and maximum-output-swing bandwidths, low distortion, high slew rate, input-protection diodes, and output short-circuit protection. These operational amplifiers are compensated internally for unity-gain operation. These devices have specified maximum limits for equivalent input noise voltage. Features
• Equivalent Input Noise Voltage: 5 nV/√Hz Typ at 1 kHz
• Unity-Gain Bandwidth: 10 MHz Typ
• Common-Mode Rejection Ratio: 100 dB Typ
• High DC Voltage Gain: 100 V/mV Typ
• Peak-to-Peak Output Voltage Swing 26 V Typ With VCC± = ±15 V and RL = 600 Ω
• High Slew Rate: 9 V/μs Typ
$0.59 Op-Amp - LF356, Single, High Slew Rate, 8-Pin DIP LF356 single op amp in an 8-pin DIP package. The LFx5x devices are the first monolithic JFET input operational amplifiers to incorporate well-matched, high-voltage JFETs on the same chip with standard bipolar transistors (BI-FET™ Technology). These amplifiers feature low input bias and offset currents/low offset voltage and offset voltage drift, coupled with offset adjust, which does not degrade drift or common-mode rejection.$0.95
Op-Amp - LM3900, Quad, Norton, 14-Pin DIP
LM3900 quad op amp in a 14-pin DIP package. These devices consist of four independent, high-gain frequency-compensated Norton operational amplifiers that were designed specifically to operate from a single supply over a wide range of voltages. Operation from split supplies is also possible. The low supply current drain is essentially independent of the magnitude of the supply voltage. These devices provide wide band- width and large output voltage swing. Features
• Wide Range of Supply Voltages, Single or Dual Supplies
• Wide Bandwidth
• Large Output Voltage Swing
• Output Short-Circuit Protection
• Internal Frequency Compensation
• Low Input Bias Current
• Designed to Be Interchangeable With National Semiconductor LM2900 and LM3900, Respectively
$0.49 Op-Amp - NE5534, Single, Low Noise, Audio, 8-Pin DIP NE5534 single op amp in an 8-pin DIP package. The NE5534 device is a high-performance operational amplifier combining excellent dc and ac characteristics. Some of the features include very low noise, high output-drive capability, high unity-gain and maximum-output-swing bandwidths, low distortion, and high slew rate. These operational amplifiers are compensated internally for a gain equal to or greater than three. Optimization of the frequency response for various applications can be obtained by use of an external compensation capacitor between COMP and COMP/BAL.$0.99
Comparator - LM311, Single, High Speed, 8-Pin DIP
LM311 single comparator IC in an 8-pin DIP package. The LM311 device is a single high-speed voltage comparator. These devices are designed to operate from a wide range of power supply voltages, including ±15-V supplies for operational amplifiers and 5-V supplies for logic systems. The output levels are compatible with most TTL and MOS circuits. These comparators are capable of driving lamps or relays and switching voltages up to 50 V at 50 mA. All inputs and outputs can be isolated from system ground. The outputs can drive loads referenced to ground, VCC+ or VCC−. Offset balancing and strobe capabilities are available, and the outputs can be wire-OR connected.
$0.49 Op-Amp - LM358, Dual, 8-Pin DIP LM358 dual op amp in an 8-pin DIP package. These devices consist of two independent, high-gain, frequency-compensated operational amplifiers designed to operate from a single supply over a wide range of voltages. Operation from split supplies also is possible if the difference between the two supplies is 3 V to 32 V (3 V to 26 V for the LM2904), and VCC is at least 1.5 V more positive than the input common-mode voltage. The low supply-current drain is independent of the magnitude of the supply voltage. Applications include transducer amplifiers, dc amplification blocks, and all the conventional operational amplifier circuits that now can be implemented more easily in single-supply-voltage systems.$0.49
Audio Power Amplifier - LM380, Class-AB, 2.5W, 14-Pin DIP
LM380 power amp in a 14-pin DIP package. The LM380 is a power audio amplifier for consumer applications. In order to hold system cost to a minimum, gain is internally fixed at 34 dB. A unique input stage allows ground referenced input signals. The output automatically self-centers to one-half the supply voltage. The output is short circuit proof with internal thermal limiting. The package outline is standard dual-in-line. The LM380N uses a copper lead frame. The center three pins on either side comprise a heat sink.
$1.95 Op-Amp - OPA134, Single, High Performance Audio, 8-Pin DIP OPA134 single op amp in an 8-pin DIP package. The OPA134 series are ultra-low distortion, low-noise operational amplifiers fully specified for audio applications. A true FET input stage is incorporated to provide superior sound quality and speed for exceptional audio performance. This, in combination with high output drive capability and excellent DC performance, allows for use in a wide variety of demanding applications. In addition, the OPA134 has a wide output swing, to within 1 V of the rails, allowing increased headroom and making it ideal for use in any audio circuit. The OPA134 SoundPlus™ audio operational amplifiers are easy to use and free from phase-inversion and the overload problems often found in common FET-input operational amplifiers. They can be operated from ±2.5-V to ±18-V power supplies.$2.95
Op-Amp - TL022, Dual, Low Power, 8-Pin DIP
TL022 dual op amp in an 8-pin DIP package. The TL022 is a dual low-power operational amplifier designed to replace higher power devices in many applications without sacrificing system performance. High input impedance, low supply currents, and low equivalent input noise voltage over a wide range of operating supply voltages result in an extremely versatile operational amplifier for use in a variety of analog applications including battery-operated circuits.
$0.69 Op-Amp - TL064, Quad, Low Power, JFET-input, 14-Pin DIP TL064 quad op amp in a 14-pin DIP package. The JFET-input operational amplifiers of the TL06x series are designed as low-power versions of the TL08x series amplifiers. They feature high input impedance, wide bandwidth, high slew rate, and low input offset and input bias currents. The TL06x series features the same terminal assignments as the TL07x and TL08x series. Features • Very Low Power Consumption • Typical Supply Current: 200 µA (Per Amplifier) • Wide Common-Mode and Differential Voltage Ranges • Low Input Bias and Offset Currents • Common-Mode Input Voltage Range Includes VCC+ • Output Short-Circuit Protection • High Input Impedance: JFET-Input Stage • Internal Frequency Compensation • Latch-Up-Free Operation • High Slew Rate: 3.5 V/µs Typical$0.59
Op-Amp - TLC274, Quad, Precision, LinCMOS, 14-Pin DIP
TLC274 quad op amp in a 14-pin DIP package. The TLC274 quad operational amplifier combines a wide range of input offset voltage grades with low offset voltage drift, high input impedance, low noise, and speeds approaching that of general-purpose BiFET devices. These devices use Texas Instruments silicon- gate LinCMOSTM technology, which provides offset voltage stability far exceeding the stability available with conventional metal-gate processes. The extremely high input impedance, low bias currents, and high slew rates make these cost-effective devices ideal for applications which have previously been reserved for BiFET and NFET products.
$1.95 Op-Amp - LM318, Single, Precision, Fast, 8-Pin DIP LM318 single op amp in an 8-pin DIP package. The LM318 is a precision, fast operational amplifier designed for applications requiring wide bandwidth and high slew rate. They feature a factor-of-ten increase in speed over general-purpose devices without sacrificing dc performance. These operational amplifiers have internal unity-gain frequency compensation. This considerably simplifies their application because no external components are necessary for operation. However, unlike most internally compensated amplifiers, external frequency compensation may be added for optimum performance. For inverting applications, feed-forward compensation boosts the slew rate to over 150 V/µs and almost double the bandwidth. Overcompensation can be used with the amplifier for greater stability when maximum bandwidth is not needed. Further, a single capacitor can be added to reduce the settling time for 0.1% error band to under 1 µs.$1.15
Op-Amp - LM358H, Dual, 8-Pin TO-99
LM358H dual op amp in an 8-pin TO-99 package. The LM358H series consists of two independent, high gain, internally frequency compensated operational amplifiers which were designed specifically to operate from a single power supply over a wide range of voltages. Operation from split power supplies is also possible and the low power supply current drain is independent of the magnitude of the power supply voltage. Application areas include transducer amplifiers, dc gain blocks and all the conventional op-amp circuits which now can be more easily implemented in single power supply systems.
$10.95 Op-Amp - LM833, Dual, Low Distortion, Audio, 8-Pin DIP LM833 dual op amp in an 8-pin dip package. The LM833 is a dual general purpose operational amplifier designed with particular emphasis on performance in audio systems. This dual amplifier IC utilizes new circuit and processing techniques to deliver low noise, high speed and wide bandwidth without increasing external components or decreasing stability. The LM833 is internally compensated for all closed loop gains and is therefore optimized for all preamp and high level stages in PCM and HiFi systems. The LM833 is pin-for-pin compatible with industry standard dual operational amplifiers. Features • Wide dynamic range: >140dB • Low input noise voltage: 4.5nV/ √ ^Hz • High slew rate: 7 V/μs (typ); 5V/μs (min) • High gain bandwidth: 15MHz (typ); 10MHz (min) • Wide power bandwidth: 120KHz • Low distortion: 0.002% • Low offset voltage: 0.3mV • Large phase margin: 60°$0.95
Op-Amp - RC4558, Dual, Low Noise, 8-Pin DIP
RC4558 dual op amp in an 8-pin DIP package. The RC4558 device is a dual general-purpose operational amplifier, with each half electrically similar to the µA741, except that offset null capability is not provided. The high common-mode input voltage range and the absence of latch-up make this amplifier ideal for voltage-follower applications. The device is short-circuit protected, and the internal frequency compensation ensures stability without external components. Features
• Continuous Short-Circuit Protection
• Wide Common-Mode and Differential Voltage Ranges
• No Frequency Compensation Required
• Low Power Consumption
• No Latch-Up
• Unity-Gain Bandwidth: 3 MHz Typ
• Gain and Phase Match Between Amplifiers
• Low Noise: 8 nV/√Hz Typ at 1 kHz

Applications
• DVD Recorders and Players
• Pro Audio Mixers
$0.39 Op-Amp - TL061, Single, Low Power, JFET-input, 8-Pin DIP TL061 single op amp in an 8-pin DIP package. The JFET-input operational amplifiers of the TL06x series are designed as low-power versions of the TL08x series amplifiers. They feature high input impedance, wide bandwidth, high slew rate, and low input offset and input bias currents. The TL06x series features the same terminal assignments as the TL07x and TL08x series. Features • Very Low Power Consumption • Typical Supply Current: 200 µA (Per Amplifier) • Wide Common-Mode and Differential Voltage Ranges • Low Input Bias and Offset Currents • Common-Mode Input Voltage Range Includes VCC+ • Output Short-Circuit Protection • High Input Impedance: JFET-Input Stage • Internal Frequency Compensation • Latch-Up-Free Operation • High Slew Rate: 3.5 V/µs Typical$0.69