Pedal Parts / DIY

Op-Amp - TL071, Single, Low-Noise, JFET-input, 8-Pin DIP
TL071 single op amp in an 8-pin DIP package. The TL07xx JFET-input operational amplifier family is designed to offer a wider selection than any previously developed operational amplifier family. Each of these JFET-input operational amplifiers incorporates well-matched, high-voltage JFET and bipolar transistors in a monolithic integrated circuit. The devices feature high slew rates, low-input bias and offset currents, and low offset-voltage temperature coefficient. The low harmonic distortion and low noise make the TL07xseries ideally suited for high-fidelity and audio pre-amplifier applications.
$0.82
Integrated Circuit - 24LC32A/P, EEPROM, 8-pin DIP
24LC32A/P EEPROM in an 8-pin DIP package commonly used in Spin FV-1 projects. The Microchip Technology Inc. 24LC32A is a 4K x 8 (32K bit) Serial Electrically Erasable PROM capable of operation across a broad voltage range (2.5V to 6.0V). It has been developed for advanced, low power applications such as personal communications or data acquisition. The 24LC32A also has a page-write capability of up to 32 bytes of data. The 24LC32A is capable of both random and sequential reads up to the 32K boundary. Functional address lines allow up to eight 24LC32A devices on the same bus, for up to 256K bits address space. Advanced CMOS technology and broad voltage range make this device ideal for low-power/low-voltage, nonvolatile code and data applications.
$1.15
Header - Round Pin, 20 Position, Breakaway, 2.54mm Spacing
20 position male pin headers with a 2.54mm (0.1”) pitch. These headers use round pins that are smaller than the standard square type and are perfect for use with IC sockets, breadboards, and machine pin sockets. The breakaway construction makes fitting them to projects simple. Features:
  • Round Pin
  • 20 Position
  • 2.54mm Spacing
  • Breakaway
$1.25
Regulator - L78L33, 3.3 Volt, Positive Voltage Regulator, TO-92
L78L33 3.3V regulator in a TO-92 package. The L78L33 three-terminal 3.3V positive regulator employs internal current limiting and thermal shutdown, making them essentially indestructible. If adequate heat-sink is provided, they can deliver up to 100 mA output current. They are intended as fixed voltage regulators in a wide range of applications including local or oncard regulation for elimination of noise and distribution problems associated with single-point regulation. In addition, they can be used with power pass elements to make high-current voltage regulators. The L78L series used as Zener diode/resistor combination replacement, offers e improvement along with lower quiescent current and lower noise. Features:
  • Output voltage of 3.3V
  • Output current up to 100 mA
  • Short-circuit protection
  • No external components are required
$0.50
Crystal - 32.768 kHz, 12.5pF, 3x8mm
Through-hole mount crystal with a 32.768 kHz (32768 Hz) frequency. This crystal has a 12.5pF capacitance and is housed in a 3mm x 8mm package that is commonly used with Spin FV-1 chips. Features:
  • 32.768 kHz Frequency
  • 3x8mm Cylinder Case
  • Through Hole
  • 12.5pF
$0.29
Knob - Davies, 1550, Daka-ware, Large, Skirted Pointer
High-quality USA made knobs from Davies Molding. The large skirted 1550 pointer knob is made of solid phenolic and features a white indicator line. The pointer has an overall length of 1.19” and the skirt’s diameter is 1.13”.
  • Height: 0.625 in
  • Length: 1.19 in.
  • Fits ¼" shaft with set screw
$1.75
Knob - Davies, 1914, Daka-ware, Medium, Scalloped Edge
High-quality USA made knobs from Davies Molding. The 1914 knob is the larger version of the classic 1900H found on countless synthesizers and pedals. This knob is made of solid phenolic and features an indicator line on the top. The knob pairs perfectly with the smaller diameter 1900 knobs such as the P-K801-BRASS-X as well as the skirted P-K234X knobs.
  • Height: 0.50 in.
  • Diameter: 0.75 in.
  • Fits ¼" shaft with set screw
$3.55
Pedal Box - 12” x 5” x 4", Fits Wah Pedals and Loopers
High quality crush-proof boxes that are perfectly sized for larger stompboxes. This cardboard box features triple wall sides and double wall front and bottom ensuring a safe housing for your pedals. The inside dimensions 12” x 5” x 4" fit wah pedals, 1032L (looper enclosure), and other large pedals along with accessories such as power supplies or cables. These boxes are ideal for storing or packaging effects pedals.
$2.59
Cloth Pedal Bag - 4” x 6”, 100% Cotton
Keep your pedals pristine with these 100% cotton bags. These drawstring bags are 4 in. x 6 in. and fit 1590B or smaller stompboxes. Cloth pedal bags are also great packaging for boutique pedal builders.
$0.75
Cloth Pedal Bag - 3” x 5”, 100% Cotton
Keep your pedals pristine with these 100% cotton bags. These drawstring bags are 3 in. x 5 in. and fit 1590A stompboxes. Cloth pedal bags are also great packaging for boutique pedal builders.
$0.65
Chassis Box - Hammond, 1590P1, Diecast, 6.02” x 3.27” x 1.98”
Large 6.02” x 3.27” x 1.98” Hammond 1590P1 enclosures. This enclosure is a great option for dense builds and is a popular choice for vintage style fuzz pedals with plenty of room for point to point wiring.
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
  • Dimensions shown are exterior dimensions.
  • Add 0.16" to enclosure depth for lid.
$13.50
Transistor - 2N5135, Silicon, TO-105 case, NPN
The 2N5135 is a silicon NPN transistor in a TO-105 case. This transistor is a close match to the rare 2N5133 but with higher voltage ratings and is in a larger package. The hFE range is less wide than the 2N5133 with more values in the range found in the batches used on vintage Big Muff pedals. The lower hFE range also makes these a great option for silicon fuzz pedals.
$1.75
Knob - Davies, 1910 and 1913, Daka-ware, Skirted
High-quality USA made knobs from Davies Molding. The skirted 1900 series knobs are made of solid phenolic and feature an indicator line on the skirt. These classic knobs have been used on a variety of equipment throughout the decades and are still popularly used on synthesizers today. The smaller 1910 knob was used on many early Serge paperface panels. Davies 1910 (Small)
  • Height: 0.50 in.
  • Diameter: 0.75 in.
  • Fits ¼" shaft with set screw

Davies 1913 (Large)
  • Height: 0.625 in.
  • Diameter: 1.13 in.
  • Fits ¼" shaft with set screw
$2.75
Knob - Davies, 1470, Daka-ware, Large, Pointer
Colors Available:
High-quality USA made knobs from Davies Molding. The large 1470 pointer knob is made of solid phenolic and features a fine ridged grip with a distinctive point. This classic knob has been used on a variety of guitar pedals such as the Klon and countless EHX effects.
  • Height: 0.50 in.
  • Length: 1.13 in.
  • Fits ¼" shaft with set screw
Starting at $1.95
Knob - Davies, 8005 & 8010, Daka-ware, Vintage Pointer
High-quality USA made knobs from Davies Molding. The 8000 series knobs are made of solid phenolic and feature a classic teardrop design. The detailed design makes these knobs a striking addition to any piece of equipment. This unique design has been used on a variety of tools and instruments. Davies 8005 (Small)
  • Height: 0.78 in.
  • Length: 1.05 in.
  • Fits ¼" shaft with set screw

Davies 8010 (Large)
  • Height: 1 in.
  • Length: 1.25 in.
  • Fits ¼" shaft with set screw
$3.95
Dial Plate - 0 to 100, Black on Brushed Metal
Dial plates with 0-100 indicator marks. These plates are a simple way to add panel graphics to controls. They are easy to install beneath the nut of a potentiometer like a washer. The silk screened graphics on the brushed metal plate gives projects a clean and professional appearance. 40mm Dial Plate
  • 40 mm (1.575”) outer diameter
  • 9.95 mm (0.392”) inner diameter
  • Best for 25.4mm (1”) or smaller knobs

60mm Dial Plate
  • 60mm (2.362”) outer diameter
  • 9.95mm (0.392”) inner diameter
  • Best for 40.6 mm (1.59”) or smaller knobs
$1.65
Terminal Strip - Barrier Strip, 5 Pole, Dual Lugs
High quality 5 pole dual barrier strip. These terminal blocks have a solid PBT base with plated brass terminals and combination head screws. Features:
  • PBT Base
  • Closed Back Design
  • Combo Phil-Slot Nickel-plated Steel Screws
  • Plated Brass Terminals
  • 5 Poles
  • 10 Lugs
  • 57.2mm Mounting Centers
  • UL 94V-0
$2.75
Regulator - LT1054, Voltage Converter w/ Regulator, 8-Pin DIP
LT1054 switched-capacitor voltage converter with regulator in an 8 pin DIP package. The LT1054 device is a bipolar, switched-capacitor voltage converter with regulator. It provides higher output current and significantly lower voltage losses than previously available converters. An adaptive-switch drive scheme optimizes efficiency over a wide range of output currents. Total voltage drop at 100-mA output current typically is 1.1 V. This applies to the full supply-voltage range of 3.5 V to 15 V. Quiescent current typically is 2.5 mA. The LT1054 also provides regulation, a feature previously not available in switched-capacitor voltage converters. By adding an external resistive divider, a regulated output can be obtained. This output is regulated against changes in both input voltage and output current. The LT1054 can also shut down by grounding the feedback terminal.
$2.25
Knob - Phenolic, Set Screw, Gaunt Chicken Head
High quality chicken head knobs with vintage gaunt design. The gaunt chicken head has a thinner band that extends above the base allowing for easy manipulation of the knob. This knob has a thick infilled indicator line and is made of solid phenolic. Fits 0.25” (6.35mm) shafts with set screw and brass insert.
  • Height: 0.67 in.
  • Length: 1.26 in.
  • Fits ¼" shaft with set screw
$1.15
Knob - Plastic, Set Screw, Skirted w/ Top Line, 0.87" Diameter
Black plastic control knob with set screw and brass insert. The grip has a thick vertical knurl with an indicator line on a raised top. This skirted knob is a close match to the knobs used on some late 1960s Fuzz Face® pedals as well as the Eric Johnson signature model. Fits ¼” (6.35mm) pot shafts.
  • Height: 0.77 in.
  • Diameter: 0.87 in.
  • Fits ¼" shaft with set screw
$0.99
On Backorder
Op-Amp - LF347, Quad, Wide Bandwidth, 14-Pin DIP
LF347 quad op amp in a 14-pin DIP package. The LF347 is a low cost, high speed quad JFET input operational amplifier with an internally trimmed input offset voltage ( BI-FET II™ technology). The device requires a low supply current and yet maintains a large gain bandwidth product and a fast slew rate. In addition, well matched high voltage JFET input devices provide very low input bias and offset currents. The LF347 is pin compatible with the standard LM348. This feature allows designers to immediately upgrade the overall performance of existing LF348 and LM324 designs. The LF347 may be used in applications such as high speed integrators, fast D/A converters, sample-and-hold circuits and many other circuits requiring low input offset voltage, low input bias current, high input impedance, high slew rate and wide bandwidth.
$0.69
Knob - Pointer, Small, Knurled, 0.675” Diameter
Colors Available:
This vintage knob design has been used on numerous boutique pedals. These classy knurled pointer knobs feature a slotted set screw, and fit ¼" solid shaft potentiometers. These are a close match to the Davies 1400.
  • Height: 0.43 in.
  • Length: 0.825 in.
  • Fits ¼" shaft with set screw
$0.69
Knob - Aluminum, Set Screw, Diamond Knurl, 0.496” Diameter
Colors Available:
Anodized aluminum knob with channeled indicator line and set screw. This slim, solid aluminum knob has a diamond knurled grip with a diameter of 0.495”. It also features a counterbore which allows it to hide pot bushings for a clean look. Fits ¼” (6.35mm) pot shafts.
  • Height: 0.56 in.
  • Diameter: 0.496 in.
  • Fits ¼" shaft with set screw
$3.50
Turret Strip - 30 Lugs, Two Rows, U-style
Two rows of 15 U-style terminals (30 total) on a black board. The U-style terminal strips are spaced 8.3mm apart allowing for more densely populated point-to-point builds. The boards are 0.063” thick.
$2.95