Pedal Parts / DIY

The Gorva Design M45 enclosure has similar dimensions to 1590A but a bit larger for practical use. It measures 100mm [3.94"] x 45mm [1.77"] x 35 mm [1.38"]. The extended dimensions allow for easier builds and top mounted jacks. Features:

• Slightly beveled top and rounded corners for a high quality look.
• Tight fit and small gap between the enclosure and lid.
• Undercut boss allows more internal room for a more flexible layout.
• Smooth, eggshell-like matte powder coating.
• Recessed bottom lid

Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure. Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. Vibra finished for a smooth surface with no sharp edges. Four 6-32 x 1/2" machine screws secure lid - into tapped holes. Designed to meet IP54. Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
Add 0.16" to enclosure depth for lid.

1591T Series enclosure made of clear polycarbonate. The 1591B is a similar size to the 1590B diecast aluminum enclosures. Includes four cover screws and pre-installed brass inserts.

• Ideally suited for mounting printed circuit boards.
• Perfect for applications where parts, sensors or indicators need to be visible.
• Crystal Clear version is almost totally transparent.
• Integral card guides accept 1.5 mm (0.062”) P.C. cards.
• Lap joint construction provides protection against access of dust and splashing water.
• Designed to meet IP54.
• Molded from flame retardant, easy to machine, translucent polycarbonate (material carries a UL flammability rating of 94V-2).
• Lid is secured with M3 x 10 mm Phillips machine screws, threaded into integral brass bushings.

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Four 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C.

1590B diecast enclosure finished in a hammered bronze powdercoat. 4.40" x 2.38" x 1.06" deep body. 1.22" with lid. Equivalent to Hammond P-H1590B.

• 4.40" x 2.38" x 1.06"
• Hammered bronze powdercoat
• Die-Cast Aluminum
• Includes Box, Lid, And Screws
• Similar to Hammond P-H1590B
• Add 0.16" to enclosure depth for lid.

Part of a limited run of hammered bronze enclosures which includes: Enclosure SKU 1590B P-H1590BCE-HMT-BRZ 1590N1 / 125B P-H1590N1CE-HMT-BRZ 1590BB P-H1590BBCE-HTM-BRZ YY P-H-YY-HMT-BRZ 1590J P-H1590J-HMT-BRZ

4.40" x 2.38" x 1.65" (112mm x 61m x 42mm) diecast aluminum enclosure. Equivalent to the Hammond 1590BS enclosure. This enclosure is a taller version of the 1590B allowing for top mounted jack and more overall area for larger projects.

Eddystone 27969PSLA enclosure with similar dimensions to the Hammond 1590A enclosure. The Eddystone version has sharper corners for a distinctive appearance. This enclosure is a great option for 1590A style builds.

• Rugged, diecast aluminum alloy (tough - yet easy to machine), electronic instrument enclosure.
• Aluminum alloy to BS1490, LM2M - supplied in natural finish.
• Eddystone designed. The Eddystone brand was purchased by Hammond in 1998.
• Lap joint construction provides protection against access of dust and splashing water. Also provides excellent EMC performance.
• Lids are retained by M3.5 x 12 countersunk screws (POZIDRIV No. 2 head).
• Countersunk lid holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Four 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C.

1590N1 / 125B diecast enclosure finished in a hammered bronze powdercoat. Equivalent to Hammond P-H1590N1. Depending on the manufacturer, this enclosure is usually very similar to a 125B.

• 4.77" x 2.58" x 1.41"
• Hammered bronze powdercoat
• Die-Cast Aluminum
• Includes Box, Lid, And Screws
• Similar to Hammond P-H1590N1
• Add 0.16" to enclosure depth for lid.

Part of a limited run of hammered bronze enclosures which includes: Enclosure SKU 1590B P-H1590BCE-HMT-BRZ 1590N1 / 125B P-H1590N1CE-HMT-BRZ 1590BB P-H1590BBCE-HTM-BRZ YY P-H-YY-HMT-BRZ 1590J P-H1590J-HMT-BRZ

1.99″ x 1.99″ x 1.22″ (51mm x 51mm x 31mm) diecast aluminum enclosure. Equivalent to the Hammond P-H1590LBX enclosure. This enclosure is great for tap tempos and other utility pedals.

Uniquely shaped trapezoid Hammond enclosure. Screws included.

Eddystone 29830PSLA enclosure with similar dimensions to the Hammond 1590BB enclosure. The Eddystone version has sharper corners for a distinctive appearance. This enclosure is a great option for 1590BB style builds.

• Rugged, diecast aluminum alloy (tough - yet easy to machine), electronic instrument enclosure.
• Aluminum alloy to BS1490, LM2M - supplied in natural finish.
• Eddystone designed. The Eddystone brand was purchased by Hammond in 1998.
• Lap joint construction provides protection against access of dust and splashing water. Also provides excellent EMC performance.
• Lids are retained by M3.5 x 12 countersunk screws (POZIDRIV No. 2 head).
• Countersunk lid holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.

4.40" x 2.38" x 1.06" D. Equivalent to Hammond P-H1590B.
Add 0.16" to enclosure depth for lid.

Predrilled 1590BB enclosures. Measures 4.71" x 3.70" x 1.18" deep. These enclosures come drilled with holes for pots, footswitch and top mounted jacks.

• Standard size footswitch mounting hole fits 12mm or 15/32” bushings
• ⅜” mounting holes for top mounted jacks
• Enclosed or low profile ¼” jacks recommended
• Top mounted DC jack mounting hole fits common switched jacks such as S-H750-X and P-JBLB-IN-S
• 8mm potentiometer mounting holes fit a variety of different pot sizes but 16mm pots are recommended.

Slanted YY enclosures perfect for fuzz pedals and other vintage style effects. In addition to the classic slant, this enclosure features thick diecast walls and a recessed bottom cover. The four bottom plate cover screws are included. Features

• Vintage style slant
• Flat top-section for mounting controls
• Recessed lid
• Thick diecast construction

The Hammond 1590B2 is a version of the ubiquitous 1590B with a little more vertical space. Great for any designs that require more clearance and allows for easier top-mounted jacks.

Pre-drilled wedge shaped pedal enclosure by Mod® Electronics. The shape of this folded steel enclosure is inspired by the original FZ-1 and FZ-1A Fuzz Tone enclosures but the predilled layout is inspired by the Octavio and the early Carlsbro fuzz. This provides a classic pedal design with a layout that is more compatible with modern pedalboards than the original Fuzz Tone layout. The layout is intended for two pots, two jacks, and a footswitch so many fuzz varieties can be built in this enclosure. The wedge shaped fuzz enclosure features a hinged bottom cover for easy access to the battery. The four screws that attach the bottom are included.

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Six 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C.

Large 6.02” x 3.27” x 1.98” Hammond 1590P1 enclosures. This enclosure is a great option for dense builds and is a popular choice for vintage style fuzz pedals with plenty of room for point to point wiring.

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Four 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
• Dimensions shown are exterior dimensions.
• Add 0.16" to enclosure depth for lid.

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Four 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
• Dimensions shown are exterior dimensions.
• Add 0.16" to enclosure depth for lid.

YY enclosure finished in a hammered silver powdercoat. The slanted YY enclosures are perfect for fuzz pedals and other vintage style effects. In addition to the classic slant, this enclosure features thick diecast walls and a recessed bottom cover. The four bottom plate cover screws are included. Features

• Vintage style slant
• Hammered silver powdercoat
• Flat top-section for mounting controls
• Recessed lid
• Thick diecast construction

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Six 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
• Dimensions shown are exterior dimensions.

30° sloped aluminum consoles from Hammond’s 1456 Series. These enclosures are a great choice for desktop effects and synthesizers as well as vintage style stompboxes. Features:

• 4" x 5.5" x 3" (1” height at front)
• Bottom panels are 0.081” (2 mm) thick aluminum
• Top panels are 0.064” thick aluminum
• Fully Powder Coated
• Comes with self adhesive rubber feet and required mounting hardware.

1590BB diecast enclosure finished in a hammered silver powdercoat. The 1590BB chassis box is perfectly suited for effects pedals and other DIY projects.

• 4.71" x 3.70" x 1.18"
• Hammered silver powdercoat
• Die-Cast Aluminum
• Includes Box, Lid, And Screws
• Similar to Hammond P-H1590BB
• Add 0.16" to enclosure depth for lid.