Pedal Parts / DIY

Steel shank / steel mandrel blind rivets with a ⅛” diameter. Blind rivets, also referred to as pop rivets, can be used to join or fasten two components without requiring access to the backside of the panel or chassis. The installation is quick and results in a joint that can be stronger and tighter than a screw. These rivets are useful for securing tube sockets or other hardware such as battery holders on stompboxes.

Linear taper, vertical mount, Alpha pots with a 6mm T18 knurled shaft. These 9mm pots are popular in DIY guitar pedals, synthesizers, and other projects. Mounting nut and washer included.

FXCore from Experimental Noize is a DSP designed for creating audio effects in pro-audio devices. FXCore can operate as a standalone device when paired with appropriate CODECs where it generates all necessary clocks or as part of a more complex system where it will lock to the word clock and bit clock provided by another part of the system.
FXCore can store up to 16 programs and their associated register preset values in its internal FLASH memory so no external program storage is required.

Steel, type A narrow. SAE washers have a tighter fit on the bolt and a smaller outside diameter. Designed for general purpose mechanical and structural use.

High quality manila paper tags. These tags are pre-strung with a soft string gentle enough to use on the most delicate equipment. The paper is heavy duty 13 point stock and the ¼” eyelet is reinforced to resist tearing. These are great tags for pricing, labeling, and cataloging equipment.

The AS394CH is a junction isolated ultra well-matched monolithic NPN transistor pair with an order of magnitude improvement in matching over conventional transistor pairs. Electrical characteristics of these devices such as drift versus initial offset voltage, noise, and the exponential relationship of base-emitter voltage to collector current closely approach those of a theoretical transistor. Extrinsic base and emitter resistances are very low, giving very low noise and operating over a wide current range. To guarantee long term stability of matching parameters, internal clamp diodes have been added across the emitter-base junction of each transistor. These prevent degradation due to reverse biased emitter current, the most common cause of field failures in matched devices.

Solderable PC BreadBoard enables you to transfer your circuit and wires from a plug-in breadboard without recutting wires or changing your layout. This breadboard has the same pattern as a standard 400 connection point solderless plug-in breadboard which has a standard 5-hole strip for each IC pin, just like solderless breadboards. However, it has the advantage that soldered joints provide a more reliable long-term connection than solderless contacts. The board has four power rails like solderless breadboards, plus two bonus rails for power or signals. There are bonus two-hole pads along the centerline allowing DIL (dual in-line) headers to be used as well as a top side silkscreen to position components. Four mounting holes allow your projects to be secured.

Stereo jack for Dunlop effects pedals. Original Dunlop replacement part. Though hole PCB mount with six pins.

SFT319 PNP germanium transistors. The SFT319 is a popular PNP for fuzz pedals and other effects. This transistor is in a 18B4 package with long leads commonly found on germanium transistors. This style of package can be found in Italian built Vox Tonebenders.

LM1458 dual op amp in an 8-pin DIP package. The LM1458 is a general purpose dual operational amplifier. The two amplifiers share a common bias network and power supply leads. Otherwise, their operation is completely independent. Features

• No Frequency Compensation Required
• Short-Circuit Protection
• Wide Common-Mode and Differential Voltage Ranges
• Low-Power Consumption
• 8-Lead TO-99 and 8-Lead PDIP
• No Latch Up When Input Common Mode Range is Exceeded

LM741 single opamp in an 8-pin DIP package. The LM741 has been used in classic guitar pedals such as the Distortion Plus.
The LM741 series are general purpose operational amplifiers which feature improved performance over industry standards like the LM709. They are direct, plug-in replacements for the 709C, LM201, MC1439 and 748 in most applications. The amplifiers offer many features which make their application nearly foolproof: overload protection on the input and output, no latch-up when the common mode range is exceeded, as well as freedom from oscillations.

A great digital reverb sound that easily replaces a spring reverberation unit. Simple interface requires only input, output, +5V, and ground. Output requires no external capacitors.

CD4047B consists of a gatable astable multivibrator with logic techniques incorporated to permit positive or negative edge-triggered monostable multivibrator action with retriggering and external counting options. Inputs include +TRIGGER, -TRIGGER, ASTABLE, ASTABLE\, RETRIGGER, and EXTERNAL RESET. Buffered outputs are Q\, Q and OSCILLATOR. In all modes of operation, and external capacitor must be connected between C-Timing and RC-Common terminal, and an external resistor must be connected between the R-Timing and RC-Common terminals. Astable operation is enabled by a high level on the STABLE input or a low level on the ASTABLE\ input, or both. The period of the square wave at the Q and Q\ Outputs in this mode off operation is a function of the external components employed. "True" input pulses on the ASTABLE input or "Complement" pulses on the ASTABLE\ input allow the circuit to be used as a gatable multivibrator.

2N321 PNP germanium transistors. The 2N321 is a popular PNP for fuzz pedals and other effects. This transistor is in a TO-5 package with long leads commonly found on germanium transistors.

Audio taper, vertical mount, Song Huei pots with a 6mm shaft. These 9mm pots are popular in DIY guitar pedals, modular synthesizers, and other projects where space is limited. The knurled shaft features a painted indicator line so no knob is required. These tall versions have a 17mm shaft length and a total height of 25mm. For linear taper versions, see R-VSHL-BX. For center notched, linear taper versions, see R-VSHL-BX-CN.

Ceramic disc capacitors rated for up to 2kV, ± 10% tolerance.

1590B diecast enclosure finished in a hammered silver powdercoat. 4.40" x 2.38" x 1.06" deep body. 1.22" with lid. Equivalent to Hammond P-H1590B.

• 4.40" x 2.38" x 1.06"
• Hammered silver powdercoat
• Die-Cast Aluminum
• Includes Box, Lid, And Screws
• Similar to Hammond P-H1590B
• Add 0.16" to enclosure depth for lid

TL071 single op amp in an 8-pin DIP package. The TL07xx JFET-input operational amplifier family is designed to offer a wider selection than any previously developed operational amplifier family. Each of these JFET-input operational amplifiers incorporates well-matched, high-voltage JFET and bipolar transistors in a monolithic integrated circuit. The devices feature high slew rates, low-input bias and offset currents, and low offset-voltage temperature coefficient. The low harmonic distortion and low noise make the TL07xseries ideally suited for high-fidelity and audio pre-amplifier applications.

Premium three position DPDT mini toggle switches from Gorva Design. The Bascular Mini switches have a medium 7.5mm actuator length. These switches feature silver plated copper contacts. RoHS compliant & lead-free. Mounting hardware included. Details

• 8.89 mm bushing length
• Medium bat
• 3-Position On/On/On
• ¼" mounting hole diameter
• Double pole/Double throw (DPDT)
• Solder lugs

Features:

• Power Rating: DC9V, 1A
• Contact Resistance: <10mΩ
• Insulation Resistance: 1000MΩ Minimum
• Dielectric Strength: 1000V RMS @ Sea Level
• Operating Temperature: -40°C ~ +85°C
• Electrical Life: 40,000 Cycles
• RoHS & Lead-free

The BTSE-16FX Effect board provides 16 different digital audio effects to be used for mixers or other audio applications that require sound enhancement. Equipped with the superb quality digital effects processing engine which it adds that extra punch needed to make audio presentations truly stand out.

Danger high voltage label for amplifiers and other equipment. These stickers are a great option for labeling equipment and builds as high voltage whenever necessary. The sticker is a single piece that must be cut to size using scissors or a paper cutter to make a total of four labels. This style of label is perfect for smaller areas like circuit boards, components, heatsinks and other areas inside the chassis.

Slanted YY enclosures perfect for fuzz pedals and other vintage style effects. In addition to the classic slant, this enclosure features thick diecast walls and a recessed bottom cover. The four bottom plate cover screws are included. Features

• Vintage style slant
• Flat top-section for mounting controls
• Recessed lid
• Thick diecast construction

Black bodied 3PDT footswitches perfect for custom pedal builds. These footswitches feature a low actuation force for fast and responsive switching. Color options are available to dial in the look of your next build. Matching mounting hardware is included.

Switchcraft 1/4" stereo jack, 4 solder lugs include: tip, tip-shunt, ring and sleeve.