Pedal Parts / DIY

Chassis Box - 1590G2, Diecast, 3.9" x 2.0" x 1.2"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
  • Dimensions shown are exterior dimensions.
  • Add 0.16" to enclosure depth for lid.
$7.95
Terminal Strip - 4 Lug, 2nd Lug Common, Horizontal
Package of 5
Standard size terminal strips, 1/16" thick bakelite, tin plated steel solder lugs and brackets on 3/8" centers.
$4.25
Relay Module - Lehle, Relay True Bypass Switching Unit
The LEHLE MODULE SW is a true bypass switching unit with relay and an active pop suppression function controlled by an intelligent microcontroller circuit, thereby allowing the LEHLE MODULE SW to switch even faster than mechanical switches, noise-free and without wear.
Starting at $22.95
Knob - Peavey, Black Pointer, White Line
Black pointer with white line. Fits a 3/16" knurled shafts. Push on Peavey part: 70902145
$3.95
¼" Jack - Stereo, PC Mount, metric threading
1/4" stereo jack. 3 PC mount terminals include: tip, ring and sleeve. Metric threading: M12 x 1.0.
$1.95
Knob - Dunlop, MXR, small knurled, aluminum
Genuine Dunlop replacement small knurled knob for MXR pedals. Push -on style knob designed for use with coarse knurled shafts.
$2.25
¼" Jack - Pure Tone, Stereo, Double-Open Circuit, Long Thread
Pure Tone’s new long threaded three pole (stereo) 1/4" jack provides full contact for improved connections and signal integrity. This jack locks the cable securely into place creating a greater surface area connection to carry more signal for an improved frequency stability. This jack is a great choice for both mono and stereo applications as well as guitars using active electronics.
$9.99
Cable - Power All, Red Right Angle Reverse Polarity Jumper
Included in the Power-All System and also available separately, the Cable-Red/R allows the user to power effect units that have reverse polarity barrel connectors (tip positive/barrel negative). The Cable-Red/R features a tip positive, male barrel connector that is spring-loaded to prevent disconnection. The Cable-Red/R can be hooked to any plug on any of the Power-All daisy chains, or directly to the Power-All.
$3.00
Op-Amp - LM741, Single, general purpose, 8-Pin DIP
LM741 single opamp in an 8-pin DIP package. The LM741 has been used in classic guitar pedals such as the Distortion Plus.
The LM741 series are general purpose operational amplifiers which feature improved performance over industry standards like the LM709. They are direct, plug-in replacements for the 709C, LM201, MC1439 and 748 in most applications. The amplifiers offer many features which make their application nearly foolproof: overload protection on the input and output, no latch-up when the common mode range is exceeded, as well as freedom from oscillations.
$0.79
Footswitch - 3PDT, Blue, Taiwan-made, latching-type
Good stomp-box effects switch (Triple Pole, Double Throw). 3PDT Latching type footswitch. Made in Taiwan.
$6.95
Heat Shrink - ¼" Diameter x 6" Long, 23 Pieces
Package of 23
The shrink ratio on this tubing is 2 to 1, it is fungus resistant and non-corrosive. It is recommended for tightly sealing connectors, terminals, wire splices, and tool handles. It may be shrunk with heat guns, oven, etc. Comes in 6 inch lengths, quantity of 23.
$6.95
Inductor - Dunlop, for Crybaby, HI01 Halo Inductor
Cry Baby Genuine Replacement Part HI01 Halo Inductor. Used in the famous Clyde McCoy® wah, the Halo Inductor is the key to late ’60s American wah tone. The HI01 delivers that vintage sound, with its expressive sweep and throaty voice, while minimizing microphonic noise due to its stabilized cup-core material.
$45.95
¼" Jack - Rean, Mono, Open Circuit
2 pole open 1/4" jack, 2 contacts, with washer and nut, panel thickness 3.5 mm, with 0.205" faston tabs
$1.25
Battery Box - Dunlop, snap-in enclosure
Original Dunlop snap-in, black battery box with snap-closed swing door for effects pedals using one 9 volt battery (accessed via the bottom of the pedal). Cutout dimensions: 2.46" x 1.27", box depth: 0.70", snaps over a panel thickness of about 0.04". Used on Dunlop Cry Baby Wah Wah GCB95 and many Dunlop effects pedals.
$1.95
Chassis Box - 1032L, Diecast, Looper, 10" x 2.75" x 2.05"
Extra long diecast aluminum chassis commonly used for looper/loop-switching pedals. This enclosure style is often referred to as the 1032L. Mounting screws for the bottom plate are included with this chassis box.
$10.95
Op-Amp - TL074, Quad, Low-Noise, JFET Input, 14-Pin DIP
Low noise JFET quad operational amplifier. Incorporates well matched, high-voltage JFET and bipolar transistors in a monolithic integrated circuit. Features high slew rates, low input bias and offset currents, and low offset voltage temperature coefficients. Features:
  • Wide common-mode and differential voltage range
  • Low input bias and offset current
  • Low noise en = 15 nV/HZ
  • Output short-circuit protection
  • High input impedance JFET input stage
  • Low harmonic distortion: 0.01%
  • Internal frequency compensation
  • Latch up free operation
  • High slew rate: 16 V/us (typical)
$1.15
¼" Jack - Cliff, PC Mount, for Marshall, metal nut
PC terminals, switched. Metal ferrule, vintage style.
Starting at $2.30
$5.50
Bezel - Cliff, Black for S4 Jack Socket
Genuine Cliff™ replacement bezel for S4 Series jacks. These can be used with any of our Cliff™ jacks using the metal ferrule style nut. Sold individually.
$0.20
Terminal Strip - 5 Lug, 3rd Lug Common, Horizontal
Package of 5
Standard size terminal strips, 1/16" thick bakelite, tin plated steel solder lugs and brackets on 3/8" centers.
$4.75
Resistors - ⅛ Watt, Metal Film, 1% tolerance
Package of 5
Metal Film resistors consist of a resistive element of an extremely thin layer of metal alloy vacuum deposited on a substrate. Precise and quiet. These 1/8W resistors have a very small body and are great for tight builds.
$0.65
LED Bezel - for 3mm LED, used for mounting
Holder for mounting LEDs to panels.
$0.65
Footswitch - 3PDT, Blue, latching-type
Good stomp-box effects switch (Triple Pole, Double Throw). 3PDT Latching type footswitch. Made in China.
$2.95
Trimmer - Bourns, 3296Y, Multiturn, Top Adjust, PCB Mount
High-quality Bourns 3296Y trimpots. These sealed cermet trimmers have 25 turns for precision setting. ±10% tolerance.
$1.65