Pedal Parts / DIY

0.002uF ceramic disc capacitor rated for up to 1kV, ± 10% tolerance.

12 ½" mm, stereo, insulated, PC mount, bushing length = 0.29".

High-quality USA made knobs from Davies Molding. The large skirted 1550 pointer knob is made of solid phenolic and features a white indicator line. The pointer has an overall length of 1.19” and the skirt’s diameter is 1.13”.

• Height: 0.625 in
• Length: 1.19 in.
• Fits ¼" shaft with set screw

Linear taper, vertical mount, dual gang Alpha pots with a 6.35mm shaft diameter. Dual gang pots are useful for stereo controls and other circuits requiring two separate pots moving in tandem. These 9mm pots are popular in DIY guitar pedals, synthesizers, and other projects. Mounting nut and washer included. See R-VAV-A100K-DUAL for an audio taper version.

Small 42TM022 audio transformers with a 1.5KΩ:600Ω impedance. This transformer is a popular choice for octavia style builds as well as ring modulators. The leads are soft metal wire and can be adjusted to fit a variety of applications. RoHS compliant. Rated for 200mW.

Pre-drilled three knob pedal enclosure made of pressed steel. This large enclosure is a close match to the original enclosures found on various vintage fuzz effects such as the Vox Tone Bender MKIII, Rotosound Fuzz, and Park Fuzz Sound. It features three holes for potentiometers, two top mounted holes for ⅜” jacks, and a footswitch hole. Comes with 4 rubber feet and a pack of mounting screws(packaged separately) for attaching the bottom plate.

• Footswitch Hole Diameter: 0.492 in. (12.5mm)
• Potentiometer Hole Diameter: 0.294 in. (7.47mm)
• Jack Hole Diameter: 0.447 in. (11.35mm)

Plastic chicken head knobs for coarse knurled shafts. These tiny chicken head knobs are great for pedal builds or cramped face plates. They feature an inlay indicator line. The total length of the chicken head is 0.93 inches. Fits T18 knurled shafts.

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Four 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
• Dimensions shown are exterior dimensions.
• Add 0.16" to enclosure depth for lid.

Used in Jimi Hendrix's WAH and Dunlop volume pedal. 470 kΩ. Original Dunlop replacement part.

PCBs with similar styling to the eyelet/fiberboard used in vintage equipment. The spacing between pads is 7.5mm horizontally and 26mm vertically.

Our 3PDT PCB daughterboard is a small board designed to simplify the wiring of 3PDT footswitches in guitar pedals. All inputs and outputs are clearly labeled on the PCB, removing any confusion about how the footswitch should be wired, and decreasing the chances of wiring mistakes or short-circuits.

The NJM2120 is a dual operational amplifier of 2-INPUT and 1-OUTPUT with analog switch. The NJM2120 can be used as analog switch under the condition of GV=0dB, as Switch + Amp in order that each gain (A or B) can be adjusted independently. Each amplifier of the NJM2120 has the same electrical characteristics as the NJM4558. The NJM2120 is suitable for audio, video, electrical musical instrument, etc.

100kΩ dual-gang 16mm potentiometers with a solid shaft and an audio taper. These pots have solder lug terminals. The smaller size is useful for builds with limited panel space such as guitar pedals, synthesizer modules, and adding modifications to equipment. Washer and nut included.

• Threading: M7 x 0.75
• Distance between terminals: 5 mm (0.197”)
• Bushing Length: 6.5mm (0.256")
• Shaft Diameter: 6.35mm ( 0.250")
• Taper: Audio (Log)

Carling, SPDT mini toggle with short actuator, 3 positions, ¼" mounting hole diameter, 0.354" bushing length.

• 0.354" bushing length
• 3-Position On/Off/On
• ¼" mounting hole diameter
• Single pole/Double throw (SPDT)
• Solder lugs

Holder for mounting LEDs to panels.

The BC209C is a silicon NPN transistor in a TO-106 case. The BC209C is primarily intended for general purpose audio applications. BC209C transistors were used in original silicon Fuzz Face® pedals as well as a variety of D*A*M pedals.

The AS3046 is Alfa’s version of the CA3046 IC in an SOIC package. The AS3046D consists of five general purpose silicon NPN transistors on a common monolithic substrate. Two of the transistors are internally connected to form a differentially-connected pair. The transistors are well suited to a wide variety of applications in low power systems. They may be used as discrete transistors in conventional circuits however, in addition, they provide the very significant inherent integrated circuit advantages of close electrical and thermal matching. The AS3046D is available in a 14-pin SOIC package. Features

• Matched pair of npn transistors
• VBE matched less than ±1 mV
• 5 general purpose monolithic transistors
• Wide operating current range

Applications

• Filters
• Custom designed differential amplifiers
• Temperature compensated amplifiers

Genuine Dunlop replacement housing screws for MXR/ Dunlop pedals. Replace lost screws and keep your battery access plate on tight. 6-32 thread, Phillips head.

TL084 quad op amp in a 14-pin DIP package. These devices are low cost, high speed, dual JFET input operational amplifiers with an internally trimmed input offset voltage ( BI-FET II™ technology). They require low supply current yet maintain a large gain bandwidth product and fast slew rate. In addition, well matched high voltage JFET input devices provide very low input bias and offset currents. The TL082 is pin compatible with the standard LM1558 allowing designers to immediately upgrade the overall performance of existing LM1558 and most LM358 designs. These amplifiers may be used in applications such as high speed integrators, fast D/A converters, sample and hold circuits and many other circuits requiring low input offset voltage, low input bias current, high input impedance, high slew rate and wide bandwidth.

Cliff S4 PC-A (L Leg). Stereo input jack, metal nut, 6 pin pc mount. Low-noise Ni-Ag® Alloy Self-Cleaning Contacts for superior performance and reliability Tough, molded grade 1 black Nylon body. Supplied with a black nylon hexagonal mounting nut. Designed to receive both mono and stereo ¼" jack plugs.

DPDT momentary footswitch. AC125V/4A AC250V/2A. Rated for 50,000 make-and-break cycles at full load.

High quality phenolic pointer knob with a vintage design. The retro pointer has a thick band that extends above the base allowing for easy manipulation of the knob making it a great option for rotary controls and switches. This solid phenolic knob has an infilled indicator line with a decorative diamond shaped top. Fits 0.25” (6.35mm) shafts with set screw and brass insert. This knob pairs perfectly with the smaller P-K356 knob.

• Height: 0.85 in.
• Length: 1.63 in.
• Fits ¼" shaft with set screw

Two rows of 18 U-style terminals (36 total) on a black board. This U-style terminal strip is extra dense with 6.35mm terminal spacing allowing for even more densely populated point-to-point builds. The boards are 0.063” thick.

Included in the PA-9ECB Basic Kit and also sold separately, the Cable-Grey allows the user to power vintage and boutique effect units that run off 9-volt batteries but do not have an external AC power jack. The Cable-Grey hooks directly to the unit's Battery Snap and can be connected to any of the Power-All daisy chains, or directly to the Power-All.