Pedal Parts / DIY

Uniquely shaped trapezoid Hammond enclosure. Screws included.

Pre-drilled wedge shaped pedal enclosure by Mod® Electronics. The shape of this folded steel enclosure is inspired by the original FZ-1 and FZ-1A Fuzz Tone enclosures but the predilled layout is inspired by the Octavio and the early Carlsbro fuzz. This provides a classic pedal design with a layout that is more compatible with modern pedalboards than the original Fuzz Tone layout. The layout is intended for two pots, two jacks, and a footswitch so many fuzz varieties can be built in this enclosure. The wedge shaped fuzz enclosure features a hinged bottom cover for easy access to the battery. The four screws that attach the bottom are included.

Solderable PC BreadBoard enables you to transfer your circuit and wires from a plug-in breadboard without recutting wires or changing your layout. This breadboard has the same pattern as a standard 400 connection point solderless plug-in breadboard which has a standard 5-hole strip for each IC pin, just like solderless breadboards. However, it has the advantage that soldered joints provide a more reliable long-term connection than solderless contacts. The board has four power rails like solderless breadboards, plus two bonus rails for power or signals. There are bonus two-hole pads along the centerline allowing DIL (dual in-line) headers to be used as well as a top side silkscreen to position components. Four mounting holes allow your projects to be secured.

CD4093B consists of four Schmitt-trigger circuits. Each circuit functions as a two-input NAND gate with Schmitt-trigger action on both inputs. The gate switches at different points for positive- and negative-going signals. The difference between the positive voltage (VP) and the negative voltage (VN) is defined as hysteresis voltage (VH). Features:

• Schmitt-trigger action on each input with no external components
• Hysteresis voltage typically 0.9 V at VDD = 5 V and 2.3 V at VDD = 10 V
• Noise immunity greater than 50%
• No limit on input rise and fall times
• Standardized, symmetrical output characteristics
• 100% tested for quiescent current at 20 V
• Maximum input current of 1 µA at 18 V over full package-temperature range, 100 nA at 18 V and 25°C
• 5-V, 10-V, and 15-V parametric ratings
• Meets all requirements of JEDEC Tentative Standard No.

TLC274 quad op amp in a 14-pin DIP package. The TLC274 quad operational amplifier combines a wide range of input offset voltage grades with low offset voltage drift, high input impedance, low noise, and speeds approaching that of general-purpose BiFET devices. These devices use Texas Instruments silicon- gate LinCMOSTM technology, which provides offset voltage stability far exceeding the stability available with conventional metal-gate processes. The extremely high input impedance, low bias currents, and high slew rates make these cost-effective devices ideal for applications which have previously been reserved for BiFET and NFET products.

The Dunlop 18V power supply for Dunlop effects will save you some money on batteries and get the right power to your pedal! Features Include:

• 18 volts of regulated DC current
• 2.1 mm x 5.5 mm plug with negative center

Compatible Dunlop pedals include:

• Older Crybaby Multi-Wah
• SW-95 Slash Wah
• M108 10-band EQ
• KFK1 10-band EQ
• M117R Flanger
• EVH 117 Flanger
• DD11 Dime Distortion
• M134 Chorus
• M181 Bass Blowtorch

Plus many other pedals requiring an 18vdc power supply!

Extra long diecast aluminum chassis commonly used for looper/loop-switching pedals. This enclosure style is often referred to as the 1032L. Mounting screws for the bottom plate are included with this chassis box. Add 0.16" to enclosure depth for lid.

30° sloped aluminum consoles from Hammond’s 1456 Series. These enclosures are a great choice for desktop effects and synthesizers as well as vintage style stompboxes. Features:

• 4" x 5.5" x 3" (1” height at front)
• Bottom panels are 0.081” (2 mm) thick aluminum
• Top panels are 0.064” thick aluminum
• Fully Powder Coated
• Comes with self adhesive rubber feet and required mounting hardware.

Zonk II style circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in the Zonk II pedal. The board is styled after the version that featured silicon transistors and a printed circuit rather than a stripboard construction. It is actually a cut down version of the Shatterbox PCB using only the fuzz side of that pedal. When drawing the layout, original boards were closely referenced to ensure a proper match and fit. The copper traces have a surface treatment providing protection from corrosion. This board includes a blank mounting PCB. This PCB sits directly beneath the main board to mount it directly to the enclosure using screws. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below.

The 2N4403 is a silicon general purpose PNP transistor in a TO-92 package. The 2N4403’s typical applications include signal processing, amplification, and switching.

The BC546 is a silicon general purpose NPN transistor in a TO-92 package. The BC546’s typical applications include signal processing, amplification, and switching. The BC546 is available in two different gain ranges: BC546B and BC546C. Type hFE (IC=2mA, VCE=5V) BC546B 200-450 BC546C 420-800

High quality crush-proof boxes that are perfectly sized for larger stompboxes. This cardboard box features triple wall sides and double wall front and bottom ensuring a safe housing for your pedals. The inside dimensions 12” x 5” x 4" fit wah pedals, 1032L (looper enclosure), and other large pedals along with accessories such as power supplies or cables. These boxes are ideal for storing or packaging effects pedals.

Original Cliff sealed and switched blue jack. Fully threaded. Many types of professional music equipment nowadays use high power components, and need to be cooled by fans. Fans draw in dust and pollutants which can adversely affect the contacts of conventional jacks, with exposed contacts. This sealed jack avoids possibility of contamination of contacts by means of a sealing cover over the top and bottom of the jack.

Extra long nose, Serrated jaws, Green cushion grips Product Features:

• Long needle nose pliers
• Extra long nose
• Features serrated jaws
• Features green cushion grips

Included in the PA-9ECD Deluxe Kit and also sold separately, the Cable-Blue/R features a right-angle jack that allows users to power effect units that use a ⅛" (3.5 MM) phone plug connector with tip-positive polarity. The Cable-Blue/R can be connected to any male jack on the Cable-5 Daisy Chain, or directly to the ECO-Dapter® itself.

For the best Pedalboard Dual Lock and Velcro Alternative, try Power-All Power-Grip. Simple, yet ingenious, Power-Grip pedal board tape mates to itself via rows of tiny mushroom-shaped posts that form a much stronger bond than traditional "hook & loop" Velcro fasteners. Just cut to size, apply, and GRIP! Approximately enough for 6 standard-sized pedals

Carling submini toggle switch, DPDT, 2 position, .195" mounting hole diameter, 0.236" bushing length.

Carling submini toggle switch, SPDT, 2 position, .195" mounting hole diameter, 0.236" bushing length.

The AS571D is Alfa’s version of the NE571 or SA571 in an SOIC package. AS571 is a versatile low cost dual gain control circuit in which either channel may be used as a dynamic range compressor or expandor. Each channel has a full-wave rectifier to detect the average value of the signal, a linearized temperature-compensated variable gain cell, and an operational amplifier. AS571 is well suited for use in VCA blocks, noise reduction systems, compandors/expanders ,etc. Features

• Complete compressor and expandor
• Temperature compensated
• Channel separation >86 dB
• Greater than 110 dB dynamic range
• Levels adjustable with external components
• Distortion may be trimmed out

Applications

• VCA
• High level limiter
• Low level expandor − noise gate
• Dynamic filters
• Dynamic noise reduction systems

CD4017B is a 5-stage Johnson counter having 10 decoded outputs, respectively. Inputs include a CLOCK, a RESET, and a CLOCK INHIBIT signal. Schmitt trigger action in the CLOCK input circuit provides pulse shaping that allows unlimited clock input pulse rise and fall times. These counters are advanced one count at the positive clock signal transition if the CLOCK INHIBIT signal is low. Counter advancement via the clock line is inhibited when the CLOCK INHIBIT signal is high. A high RESET signal clears the counter to its zero count. Use of the Johnson counter configuration permits high-speed operation, 2-input decode-gating and spike-free decoded outputs. Anti-lock gating is provided, thus assuring proper counting sequence. The decoded output are normally low and go high only at their respective decoded time slot. Each decoded output remains high for one full clock cycle.

LM318 single op amp in an 8-pin DIP package. The LM318 is a precision, fast operational amplifier designed for applications requiring wide bandwidth and high slew rate. They feature a factor-of-ten increase in speed over general-purpose devices without sacrificing dc performance. These operational amplifiers have internal unity-gain frequency compensation. This considerably simplifies their application because no external components are necessary for operation. However, unlike most internally compensated amplifiers, external frequency compensation may be added for optimum performance. For inverting applications, feed-forward compensation boosts the slew rate to over 150 V/µs and almost double the bandwidth. Overcompensation can be used with the amplifier for greater stability when maximum bandwidth is not needed. Further, a single capacitor can be added to reduce the settling time for 0.1% error band to under 1 µs.

MPSA63 PNP Darlington transistor (TO-92 package) - designed for high gain, low noise general purpose amplifier applications.

• Max collector to emitter voltage = -30V
• Max collector to base voltage = -30 V
• Max emitter to base voltage = -10 V
• Max collector current = -0.5 A (continuous)

TL084 quad op amp in a 14-pin DIP package. These devices are low cost, high speed, dual JFET input operational amplifiers with an internally trimmed input offset voltage ( BI-FET II™ technology). They require low supply current yet maintain a large gain bandwidth product and fast slew rate. In addition, well matched high voltage JFET input devices provide very low input bias and offset currents. The TL082 is pin compatible with the standard LM1558 allowing designers to immediately upgrade the overall performance of existing LM1558 and most LM358 designs. These amplifiers may be used in applications such as high speed integrators, fast D/A converters, sample and hold circuits and many other circuits requiring low input offset voltage, low input bias current, high input impedance, high slew rate and wide bandwidth.

10kΩ dual-gang 16mm potentiometers with a T18 knurled shaft and a linear taper. These pots have right angle PCB mount terminals. The smaller size is useful for builds with limited panel space such as guitar pedals, synthesizer modules, and adding modifications to equipment. Washer and nut included.

• Threading: M7 x 0.75
• Distance between terminals: 5 mm (0.197”)
• Lead Depth from Panel: 10.7 mm + 5 mm (0.421” + 0.197”)
• Lead Distance from shaft center: 16 mm (0.630”)
• Lead Thickness: 0.5 mm (0.020”)