Pedal Parts / DIY

Replacement for Boss effects pedals, SPST momentary Off-(On), push switch. Mounts in square hole approximately. 55" x.55" x 1.08" overall length including terminals.

The 2N2369 is a silicon NPN transistor in a TO-18 metal case type. The 2N2369 is primarily intended for use in high speed switching and VHF amplification applications.

Small plastic control knob with set screw and brass insert. This knob features a radial-brushed metal top and a stylish vertical knurl. The style is similar to the Boss middle knobs used on many pedals. Fits ¼” (6.35mm) pot shafts.

Mono input. Solder lugs, shorting. Metal ferrule, vintage style. Similar to S-H901-X.

20 position male pin headers with a 2.54mm (0.1”) pitch. These headers use round pins that are smaller than the standard square type and are perfect for use with IC sockets, breadboards, and machine pin sockets. The breakaway construction makes fitting them to projects simple. Features:

• Round Pin
• 20 Position
• 2.54mm Spacing
• Breakaway

High quality chassis mount battery holder. This steel holder fits standard 9V batteries. The horizontal mount and small footprint of the holder allows for easy placement where vertical space is limited.

A great digital reverb sound that easily replaces a spring reverberation unit. Stereo outputs may be summed for mono operation. Simple interface requires only input, output, +5V, and ground.

2N408 PNP germanium transistors. The 2N408 is a popular PNP for fuzz pedals and other effects. The 2N408 was popularly used in the germanium version of the Fuzzrite by Mosrite along with the 2N2613.

The Switchcraft Type 112BX enclosed ¼” jack is a high quality jack. This jack has three solder lugs. One for the tip, one for the ring, and one for the sleeve. These jacks have been widely used across the industry and can also be found in many popular 5U synthesizers. Includes nut and washer.

• Type 112BX
• 0.276" bushing length (standard)
• Mates with standard ¼" plugs and is available with 0.25" inside diameter bushing.
• Stereo 3-Conductor
• Includes nut and washer

See W-SC-111X for mono version

Genuine Cliff™ replacement bezel for S4 Series jacks. These can be used with any of our Cliff™ jacks using the metal ferrule style nut. Sold individually.

Original Crybaby replacement circuit board for pedals made after 1990. Original Dunlop replacement part.

The 2N1711 is a silicon planar epitaxial NPN transistor in a TO-39 metal case. It is intended for use in high performance amplifiers, oscillators and switching circuits. The 2N1711 is a great choice for amplifiers where low noise is an important factor.

Carling mini-toggle switch, double pole/double throw, PC Pins. ¼" mounting hole diameter. 0.354" bushing length. 3-Position.

The NJM5532 is a high performance dual low noise operational amplifier. Compared to the standard dual operational amplifiers, such as the NJM1458, it shows better noise performance, improved output drive capability, and considerably higher small-signal and power bandwidths. it is compensated internally for voltage follower circuit. This makes the device especially suitable for application in high quality and professional audio equipment, instrumentation, control circuits, and telephone channel amplifiers Features:

• Operating Voltage = ±3V~±22V
• Small Signal Bandwidth = 10MHz typ.
• Output Drive Capability = 600Ω,10Vrms typ.
• Input Noise Voltage = 5nV/√Hz typ.
• Power Bandwidth = 140kHz typ.
• Slew Rate = 8V/µs typ.
• Bipolar Technology

Linear taper, vertical mount, Alpha pots with a 6mm D shaft. These 9mm pots are popular in DIY guitar pedals, synthesizers, and other projects. Mounting nut and washer included.

General purpose low-power PNP bipolar junction transistor, used frequently in hobbyist electronic projects. This version is lead free.
For a lead free 2N3904 see P-Q2N3904-LF.

R/A stereo jack. Replacement for Fender amps 1999-present. Similar to Fender part: 005-3450-000

Premium 9V battery clip with a rigid plastic frame. This high quality battery snap features nickel-plated phosphor bronze contacts. The six inch leads are 26 AWG stranded wire, prestripped and tinned for an easy installation.

The AS3280 is Alfa’s version of the CA3280 IC. The AS3280 consists of two variable operational amplifiers that are designed to substantially reduce the initial input offset voltage and the offset voltage variation with respect to changes in programming current. This design results in reduced "AGC thump," an objectionable characteristic of many AGC systems. Careful design of critical places of the circuit reduces the amplifier dependence upon thermal and processing variables.
The AS3280 has all the generic characteristics of an operational voltage amplifier except that the forward transfer characteristics is best described by transconductance rather than voltage gain, and the output is current, not voltage. The magnitude of the output current is equal to the product of transconductance and the input voltage.

Good stomp-box effects switch (Triple Pole, Double Throw). 3PDT Latching type footswitch. Made in China.

LF356 single op amp in an 8-pin DIP package. The LFx5x devices are the first monolithic JFET input operational amplifiers to incorporate well-matched, high-voltage JFETs on the same chip with standard bipolar transistors (BI-FET™ Technology). These amplifiers feature low input bias and offset currents/low offset voltage and offset voltage drift, coupled with offset adjust, which does not degrade drift or common-mode rejection.

High quality, radial leaded, aluminum electrolytic capacitors rated at 25VDC.

Hex nut for white Cliff Jacks, threading: 7/16-20. Also used on the footswitch jack in some Marshall amps.

Dust cover for standard size DC power jacks. This cover is simple to install and can help protect the power jack on effects pedals and other electronics using this style of DC jack. Jack sold separately.