Pedal Parts / DIY
Breadboard - Solderable PCB, 3.75” x 1.85”, Mounting Holes
Solderable PC BreadBoard enables you to transfer your circuit and wires from a plug-in breadboard without recutting wires or changing your layout. This breadboard has the same pattern as a standard 400 connection point solderless plug-in breadboard which has a standard 5-hole strip for each IC pin, just like solderless breadboards. However, it has the advantage that soldered joints provide a more reliable long-term connection than solderless contacts. The board has four power rails like solderless breadboards, plus two bonus rails for power or signals. There are bonus two-hole pads along the centerline allowing DIL (dual in-line) headers to be used as well as a top side silkscreen to position components. Four mounting holes allow your projects to be secured.
$4.75
Terminal Strip - 7 Lug, 1st & 7th Lug Common, Horizontal
Package of 5
Standard size terminal strips, 1/16" thick bakelite, tin plated steel solder lugs and brackets. 7 lugs, first and seventh lug common.
$6.75
Knob - Rogan, PT Series, 3PS, Large, Skirted, Pointer, D-Shaft
High-quality USA made knobs from Rogan Corp. These large, skirted pointer knobs from Rogan’s PT Series feature a soft rubber grip molded over a solid polymer knob. PT Series knobs can be found on synthesizer modules from Make Noise, Mutable Instruments and others. Fits 6mm D-shafts.
A variety of different sizes are available from the PT Series.
- Height: 0.71 in
- Diameter: 0.73 in
- Fits 6mm D Shafts
- Indicator on round side of D-shaft
A variety of different sizes are available from the PT Series.
$1.75
Transistor - 2N3904, TO-92 case, NPN
General purpose low-power NPN bipolar junction transistor, used frequently in hobbyist electronic projects.
$0.18
Knob - for Peavey, Black Pointer, White Line
Black pointer with white line. Fits a 3/16" knurled shafts. Push on Peavey part: 70902145
$3.20
Potentiometer - Alpha, Linear, Solid Shaft, Long PC, 16mm
Linear taper Alpha 16mm pots with a solid shaft and long PCB mount terminals. The smaller size is useful for builds with limited panel space such as guitar pedals, synthesizer modules, and adding modifications to equipment. Washer and nut included.
- Threading: M7 x 0.75
- Distance between terminals: 5 mm (0.197”)
- Lead Depth from Panel: 20.7 mm + 4 mm (0.815” + 0.158”)
- Lead Distance from shaft center: 14.3 mm (0.563”)
- Lead Thickness: 0.5 mm (0.020”)
- Shaft Diameter: 6.35 mm (0.25”)
$0.85
StripBoard - Single Sided, 6.30” x 3.94”
ST3U StripBoard is a prototyping circuit board with a standard long strip pattern. Tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads. It has 0.1" hole spacing for DIP integrated circuits and headers and other parts. It has higher quality than traditional stripboard. The holes are drilled, not punched. The base material is high-quality FR4 glass epoxy board. It has better stability and moisture resistance than boards using phenolic or SRBP (synthetic resin bonded paper), which can warp with exposure to humidity. Features
- Standard stripboard pattern, with tracks running the length of the board.
- Single-sided high-quality FR4 glass-epoxy circuit board.
- 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
$8.75
¼" Jack - Switchcraft, Mono, isolated make circuit
Switchcraft ¼" Mono 2-Conductor Input Jack, Isolated Make Circuit (Type 13). Includes nut and washer
$6.35
PCB - LED Driver, for Pedals and Synths
This small PCB is a simple way to add an indicator light that pulses to the rate of LFOs and clocks used in pedals, synthesizers, and other equipment. Simply connect the positive supply voltage to V+, ground to GND, and the output of a positive signal (0 to V+) such as an LFO or clock to the IN pad. The trimmer can adjust how the LED reacts to the signal. Fully clockwise it will simply pulse on and off when paired with a strong signal. If the signal is a sine, triangle, or any other non-pulse type signal, adjusting the trimmer counter clockwise can dial in settings that follow the shape of the waveform, brightening and dimming with the changing voltage. For certain dual op-amp LFOs in effect pedals, the signal may not go low enough to turn the LED fully off.
$0.70
Transistor - BC109, TO-18 case, NPN
BC109 NPN silicon transistors. The BC109 is a popular NPN choice for fuzz pedals and other effects such as vintage silicon Fuzz Face builds and Big Muff clones. Type hFE (IC=2mA, VCE=5V) hfe (IC=2mA, VCE=5V, f=1KHz) BC109B 200-450 240-500 BC109C 420-800 450-900
Starting at $0.95
Washer - CTS, Flat, for Potentiometers
Package of 10
Flat washer for 3/8" bushing. Perfect fit for CTS potentiometers. Package of 10.
$1.25
Op-Amp - NJM4580L, Dual, Audio, 8-Pin SIP
NJM4580L dual op amp from JRC in a SIP8 package. The NJM4580L is the same as the DIP NJM4580 (JRC4580) otherwise. The SIP version is a great replacement for dual op amps in vintage circuits as well as a space saving package for some PCB layouts. The NJM4580 is a dual operational amplifier, specially designed for improving the tone control, which is most suitable for the audio application. Featuring noiseless, higher gain bandwidth, high output current and low distortion ratio, and it is most suitable not only for acoustic electronic parts of audio pre-amp and active filter, but also for the industrial measurement tools.
$0.69
¼" Jack - Rean, Mono, Horizontal, Switched, PC, Gold
2 pole horizontal 1/4" jack, all contacts switched, gold plated contacts, chrome ferrule nut
$1.85
Chassis Box - Hammond, 1590N1, Diecast, 4.77" x 2.58" x 1.41"
Depending on the manufacturer, this enclosure is usually very similar to a 125B.
Aluminum enclosure with countersunk lid that machine screws into drilled and tapped holes. Lap joint construction provides protection from dust and water. Vibra finished, no sharp edges.
Add 0.16" to enclosure depth for lid.
Aluminum enclosure with countersunk lid that machine screws into drilled and tapped holes. Lap joint construction provides protection from dust and water. Vibra finished, no sharp edges.
Add 0.16" to enclosure depth for lid.
$12.50
Transistor - BD139, Medium Power, TO-126 case, NPN
The BD139 is a NPN medium power BJT transistor in a TO-126 package. The BD139's typical applications include audio amplifiers and drivers but is also popularly used in silicon fuzz pedals. The BD139 is available in two different gain ranges: BD139-10 and QBD139-16. Type hFE (IC=150mA, VCE=2V) BD139-10 63-160 BD139-16 100-250
Starting at $0.54
Wire - 22 AWG Solid Core, PVC, 600V, Variety Pack
Variety pack, 10 feet for each color. Great for color-coded wiring with smaller quantities. 600V stranded. Strands are tinned individually. See photos for detail. UL style 1015, rated to 105 degrees C. Perfect for new projects or rewiring any electrical equipment. 6 Pack (6 colors, 60 total feet) includes:
9 Pack (9 colors, 90 total feet) includes:
See S-W33 for 50 foot rolls of individual colors.
- Black
- Red
- Green
- White
- Yellow
- Blue
9 Pack (9 colors, 90 total feet) includes:
- Black
- Red
- Green
- White
- Yellow
- Blue
- Orange
- Brown
- Purple
See S-W33 for 50 foot rolls of individual colors.
Starting at $11.95
Battery Clip / Snap - for 9 Volt batteries
Package of 3
9 volt battery clip with 5 3/4" red and black wire lengths. Simple construction and perfect for use in effects pedals. Package of three.
$1.35
Op-Amp - LF347, Quad, Wide Bandwidth, 14-Pin DIP
LF347 quad op amp in a 14-pin DIP package. The LF347 is a low cost, high speed quad JFET input operational amplifier with an internally trimmed input offset voltage ( BI-FET II™ technology). The device requires a low supply current and yet maintains a large gain bandwidth product and a fast slew rate. In addition, well matched high voltage JFET input devices provide very low input bias and offset currents. The LF347 is pin compatible with the standard LM348. This feature allows designers to immediately upgrade the overall performance of existing LF348 and LM324 designs. The LF347 may be used in applications such as high speed integrators, fast D/A converters, sample-and-hold circuits and many other circuits requiring low input offset voltage, low input bias current, high input impedance, high slew rate and wide bandwidth.
$0.69
Diode - BAT41, Schottky, Small Signal
The BAT41 is a schottky diode used in many DIY projects. General purpose metal to silicon diode featuring very low turn-on voltage and fast switching. This device has integrated protection against excessive voltage such as electrostatic discharges.
$0.34
Integrated Circuit - PT2399, Echo / Delay
PT2399 echo/delay chip used in many DIY and commercial pedals. The PT2399 is in a DIP 16 package. Minimal external components are required for use and delay time is set with resistance.
$2.00
Switch - Carling, Mini Toggle, DPDT, 2 Position, Solder Lugs
Carling mini-toggle switch, DPDT, ideal for phase switching, coil-tapping, series/parallel pickup switching in guitars.
- 0.354" bushing length
- ¼" mounting hole diameter
- Double pole/Double throw (DPDT)
- On-On
$3.50
Transistor - 2N3392, Silicon, TO-92 case, NPN
The 2N3392 is a general purpose NPN transistor in a TO-92 case. The 2N3392 is used in some original silicon Fuzz Face pedals as well as the Brassmaster fuzz.
$0.39
Knob - Plastic, Set Screw, Fluted w/ Line, 0.745" Diameter
Plastic control knob with set screw and brass insert. This knob features a distinctive fluting similar to the popular Philmore 3010 knob. This style is also similar to the small skirted MXR knobs. Fits ¼” (6.35mm) pot shafts.
Colors Available:
$0.85
Power Jack - DC Panel Mount, 5.5mm External, 2.1mm Internal
½" panel mount with solder lugs. Round plastic with normally closed switch. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter.
Colors Available:
$0.99