You are here

Pedal Parts / DIY

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(33 pages)
P-ECB-FI-02Inductor - Dunlop, Fasel Toroidal Model, Red

This precision-wound toroidal will give the cleanest sound possible. Use the cup core model, part number P-ECB-FI-01 for a more vintage sound. The Fasel inductor is back! These near-mythical inductors are the key to the singing tonal sweep every wah player lusts for but can't capture with a new pedal. The ultimate upgrade to your current wah, these magic bullets are available exclusively from Dunlop, the new worldwide agent for Fasel of Italy. Your wah will finally give up the lush harmonic sparkle you've always heard in your head but could never coax from you rig.


$15.95
$14.36
You save: 10%
Click to read more
P-ECB-GEARGear - replacement for Wah pedal potentiometer

Generic gear (a.k.a. pinion) for wah-style potentiometers. Outer diameter = 0.48", height = 0.61". Push-on for splined 1/4" shaft. Push-on mounting allows any 1/4" splined shaft potentiometer to be equipped for use with rack and pinion shaft rotation as in a wah pedal.


$1.50
$1.35
You save: 10%
Click to read more
P-ECB-RACKRack - gear, for wahs and other pedals

Generic rack with 18 teeth for wah and other pedals using rack and pinion potentiometer shaft rotation. (Length = 1.91", width = 0.19", height = 0.25". Mounting hole diameter = 0.075")


$0.75
$0.68
You save: 9%
Click to read more
P-H-LEHLE-BTN-XFootswitch - Lehle, SPST, Momentary, Soft Click, Long Life

The LEHLE SWITCH BTN is a momentary foot switch. It is housed in an M12 threaded enclosure made of stainless steel. Thanks to the gold plated contact material its life span is at least one million switching cycles electrically and mechanically. Hardware included.


$14.95
Starting at $13.46
You save: 10%
Click to read more
P-H-LEHLE-SW-XRelay Module - Lehle, Relay True Bypass Switching Unit

The LEHLE MODULE SW is a true bypass switching unit with relay and an active pop suppression function controlled by an intelligent microcontroller circuit, thereby allowing the LEHLE MODULE SW to switch even faster than mechanical switches, noise-free and without wear.


$22.95
Starting at $20.65
You save: 10%
Click to read more
P-H1032LChassis Box - 1092L, Diecast, Looper, 10" x 2.75" x 2.05"

Extra long diecast aluminum chassis commonly used for looper/loop-switching pedals. This enclosure style is often referred to as the 1032L. Mounting screws for the bottom plate are included with this chassis box.


$9.95
$8.96
You save: 10%
Click to read more
P-H1590AChassis Box - Hammond, 1590A, Diecast, 3.64" x 1.52" x 1.06"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.

$6.22
$5.60
You save: 10%
Click to read more
P-H1590ACE-XChassis Box - 1590A, Diecast, 3.64" x 1.52" x 1.06"
Colors Available:
New!:

Rugged, diecast aluminum alloy chassis box. Equivalent to Hammond's P-H1590A.


$4.95
Starting at $4.45
You save: 10%
Click to read more
P-H1590B2Chassis Box - Hammond, 1590B2, Diecast, 4.4" x 2.3" x 1.5"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
  • Dimensions shown are exterior dimensions.
  • Add 0.16" to enclosure depth for lid.

$7.73
$6.96
You save: 10%
Click to read more
P-H1590B3Chassis Box - Hammond, 1590B3, Diecast, 4.6" x 3.0" x 1.5"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
  • Dimensions shown are exterior dimensions.
  • Add 0.16" to enclosure depth for lid.

$8.90
$8.01
You save: 10%
Click to read more

Pages

(33 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Pedal Parts / DIY