Pedal Parts / DIY

¼" Jack - Cliff, Solder Lug, for Marshall, metal nut
Solder terminals, switched. Metal ferrule, vintage style.
Features:
  • Low-noise Ni-Ag® Alloy Self-Cleaning Contacts for superior performance and reliability
  • Tough, molded grade 1 black Nylon body.
  • Made in the U.K.
  • Supplied with a metal hexagonal mounting nut
  • Designed to receive both mono and stereo 1/4" jack plugs

Withstand Voltage: 2000VDC Min. Maximum Current: 5A Temperature Rating: -10°C ~ +70°C Life (Minimum): 10,000+ Operations Nominal Contact Resistance: < 50 mΩ
Starting at $2.60
Cable - Power All, Grey Battery Snap Jumper
Included in the PA-9 Power-All System and also sold separately, the Cable-Grey allows the user to power vintage and boutique effect units that run off 9-volt batteries but do not have an external AC power jack. The Cable-Grey hooks directly to the unit's Battery Snap and can be connected to any of the Power-All daisy chains, or directly to the Power-All.
$3.00
Potentiometer - Alpha, Audio, 9mm, Vertical
Audio taper (log), vertical mount, Alpha pots with a 6.35mm shaft diameter. These 9mm pots are popular in DIY guitar pedals, synthesizers, and other projects. Mounting nut and washer included.
$1.85
Heat Shrink - flame retardant polyolefin, 7.6mm unheated, black
Sold by the yard
Very flexible, high flame retardant polyolefin heat shrink tubing. Unheated outer diameter of about 7.6 mm with a 2:1 shrink ratio. Resistant to common liquid solvents with excellent physical, chemical, and electrical performance.
$0.45
Switch - Carling, Mini Toggle, SPDT, On-On, PC Mount, right angle
Genuine Carling 2 Position Mini Toggle, On-On, Short Round Bat, Right Angle, PC Mount Features:
  • SPDT ( Single Pole/ Double Throw) On-On switch
  • 0.275" bushing length
  • 0.270” bat length
  • ¼" chassis hole diameter
  • Right angle, PC Mount terminals

Note: On-On switches may sometimes be referred to as On-None-On.
$2.50
Terminal Strip - 6 Lug, 0 Common, Horizontal
Package of 5
Standard size terminal strips, 1/16" thick bakelite, tin plated steel solder lugs and brackets.
$5.00
PCB - Daughterboard for Wiring 3PDT Footswitches
Our 3PDT PCB daughterboard is a small board designed to simplify the wiring of 3PDT footswitches in guitar pedals. All inputs and outputs are clearly labeled on the PCB, removing any confusion about how the footswitch should be wired, and decreasing the chances of wiring mistakes or short-circuits.
$0.75
Knob - Mini Indicator, Set Screw, 15mm x 11mm
Colors Available:
Mini fluted knob with infilled indicator line. Pairs well with the larger P-K850X. Fits ¼” (6.35mm) pot shafts.
  • Height: 11mm
  • Diameter: 15mm
  • Fits 1/4" shaft with set screw
Starting at $0.75
¼" Jack - Stereo, PC Mount, Switched
1/4" stereo jack. 4 PC mount terminals include: tip, tip-shunt (normally closed), ring and sleeve. Metric threading: M12 x 1.0.
$1.95
Potentiometer - Dunlop, Wah, 10 kΩ linear
Genuine Dunlop replacement potentiometer for wah/volume.
  • 10 kΩ Linear
  • Gear included
$14.50
¼" Jack - Switchcraft, Mono, Open Circuit, Gold Plated
Genuine Switchcraft Type 11 ¼” jack with complete gold plating. All metal parts are gold plated including the washer and nut.
$9.95
Chassis Box - Hammond, 1590E, Diecast, 7.40" x 4.72" x 3.07"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Six 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
  • Dimensions shown are exterior dimensions.
$21.69
Potentiometer - Song Huei, Linear, 9mm, Tall
Linear taper, vertical mount, Song Huei pots with a 6mm shaft. These 9mm pots are popular in DIY guitar pedals, modular synthesizers, and other projects where space is limited. The knurled shaft features a painted indicator line so no knob is required. These tall versions have a 17mm shaft length and a total height of 25mm. For audio taper versions, see R-VSHL-AX. For center notched linear taper versions, see R-VSHL-BX-CN.
$0.80
¼" Jack - Fender®, Mono, PC Mount, Closed Circuit
PCB mount Fender original mono jack. Closed circuit.
$5.75
Diode - 1N5817, Schottky, High Switching Speed
Schottky diode with low forward voltage drop and high switching speeds.
$0.15
Footswitch - DPDT, Momentary, PC Terminals
DPDT momentary footswitch with PC terminals. Black with 6 terminals. AC125V 4A, AC250V 2A. PC mount version of P-H503.
$4.50
Wire - Bus, 100 foot Spool, tinned copper
Solid tinned copper bus wire. 105°C temperature rating, 600V.
Starting at $6.95
Capacitor - 500V, Ceramic Disc, ± 10%
Radial ceramic capacitor.
  • Voltage rating: 500VDC
  • Tolerance: ± 10%
Starting at $0.25
¼" Jack - Rean, Stereo, Open Circuit
3 pole open 1/4" jack, 3 contacts, with washer and nut, panel thickness 3.5 mm, with 0.205" faston tabs
$1.40
Potentiometer - Dunlop, 20 kΩ, Custom Taper, Wah Pot, for Bass
Custom taper 20k Dunlop potentiometer used in 105Q Crybaby Bass Wah. 1 million cycles, maintenance free.
$23.50
Chassis Box - GØRVA Design, C65, Diecast, 4.72” x 2.56” x 1.54”
Colors Available:
The Gorva C65 is a high quality powder-coated take on the Hammond 125B size enclosure with a focus on function and design. Features:
  • Slightly beveled top and rounded corners for high quality look.
  • Tight fit and small gap between the enclosure and lid.
  • Undercut boss allows more internal room for more flexible layout.
  • Smooth, eggshell-like matte powder coating.
  • Recessed bottom lid
$14.95
Potentiometer - Alpha, 300kΩ, Linear, Knurled Shaft, 16mm
Miniature Alpha pot for guitars. 300K linear taper.
$1.50
¼" Jack - Cliff, Mono, Switched, Gold
Mono input jack. 4 solder terminals, switched. Used in modern Marshall amps.
$2.79
BreadBoard - Solderless, 400 point pattern
Solderless (plug-in) breadboard with 400 connection tie-points (i.e. 400 wire insertion holes) and 4 power rails. Solderless breadboards are great for building and testing new circuits because parts can be easily inserted and removed making them completely re-usable. This breadboard has a 300 tie-point IC-circuit area plus four 25 tie-point power rails. The housing is made of white ABS plastic, with a printed legend giving numbers and letters for columns and rows. The internal contacts are phosphor bronze with a plated nickel finish and a peelable adhesive tape backing is provided for attaching it to a surface. Be sure to check out the Zipwire™ jumper wire kits for use with this breadboard.
$4.75