Pedal Parts / DIY

Op-Amp - TL062, Dual, Low-Power, JFET Input, 8-Pin DIP
Dual low power opamps in an 8-pin DIP package. The TL062 offers a high input impedance and 1MHz bandwidth.
$0.28
Op-Amp - TL072, Dual, Low-Noise, JFET Input, 8-Pin DIP
The TL072 is a high speed JFET input dual operational amplifier incorporating well matched, high voltage JFET and bipolar transistors in a monolithic integrated circuit. The device features high slew rates, low input bias and offset current, and low offset voltage temperature coefficient.
$0.70
Op-Amp - TL074, Quad, Low-Noise, JFET Input, 14-Pin DIP
Low noise JFET quad operational amplifier. Incorporates well matched, high-voltage JFET and bipolar transistors in a monolithic integrated circuit. Features high slew rates, low input bias and offset currents, and low offset voltage temperature coefficients. Features:
  • Wide common-mode and differential voltage range
  • Low input bias and offset current
  • Low noise en = 15 nV/HZ
  • Output short-circuit protection
  • High input impedance JFET input stage
  • Low harmonic distortion: 0.01%
  • Internal frequency compensation
  • Latch up free operation
  • High slew rate: 16 V/us (typical)
$1.15
Op-Amp - TL082, Dual, Wide-Bandwidth, JFET Input, 8-Pin DIP
Dual wide-bandwidth TL082 opamps in an 8-pin DIP package. The TL082 offers a high input impedance and 4MHz bandwidth.
$0.21
DSP Module - ABE, Accu-Bell Effector, 3 Adjustable Effects
The Accu-Bell Effector offers reverb, chorus, and delay with adjustable setting and tap tempo. This module runs on 5.5V to 9.5V DC so it is easy to incorporate into effect pedal builds. Please see the attached datasheet for an example schematic.
$21.95
On Backorder
Reverb Module - Accutronics Belton, Digi-Log, horizontal mount
A great digital reverb sound that easily replaces a spring reverberation unit. Simple interface requires only input, output, +5V, and ground. Output requires no external capacitors.
Starting at $12.95
Reverb Module - Accutronics Belton, Digi-Log, horizontal, mini
A great digital reverb sound that easily replaces a spring reverberation unit. Small package is half the size of the P-RBTDR-1H-X
$14.95
Reverb Module - Accutronics, Digi-Log, vertical mount, mini
A great digital reverb sound that easily replaces a spring reverberation unit. Stereo outputs may be summed for mono operation. Simple interface requires only input, output, +5V, and ground.
$14.95
Reverb Module - Accutronics Belton, Digi-Log, Adjustable Decay
A great digital reverb sound that easily replaces a spring reverberation unit. Stereo outputs may be summed for mono operation. Simple interface: input, output, +5V, and ground
$15.95
DSP Module - Accutronics, 99 Effects (Reverb, Chorus, Delay, +)
The BTSE-99FX Effect board provides 99 different digital audio effects to be used in many audio applications that require sound enhancement. Equipped with a superb quality digital effects processing engine which adds that extra punch needed to make sounds truly stand out. Applications:
  • Guitar/ Keyboard/Bass amplifiers and combos
  • Audio mixing consoles / Powered mixing consoles
  • Stand -alone stereo effect units for studio and PA usage
  • Effects pedals
$32.00
Multi Processor Module - Belton, BTSE-16FX
The BTSE-16FX Effect board provides 16 different digital audio effects to be used for mixers or other audio applications that require sound enhancement. Equipped with the superb quality digital effects processing engine which it adds that extra punch needed to make audio presentations truly stand out.
$29.95
Relay - Panasonic, DPDT, 5V, Single Coil, Non-Latching
High quality non-latching relays from the Panasonic TQ series. These 5 volt relays are commonly used in pedals for true bypass switching. Relay switching can allow for a variety of options on pedal builds. Different footswitch modes can be obtained using the same momentary footswitch. Stereo switching using a standard footswitch is another possible option. Features:
  • Compact low profile size
  • Standard DIL spacing for easy PCB use and breadboard compatibility
  • Non-Latching
  • Single Coil
  • 5V Coil Voltage

For a latching version, please see P-RP-TQ2-L-5V.
$3.25
Relay - Panasonic, DPDT, 5V, Single Coil, Latching
High quality latching relays from the Panasonic TQ series. These 5 volt relays are commonly used in pedals for true bypass switching. Relay switching can allow for a variety of options on pedal builds. Different footswitch modes can be obtained using the same momentary footswitch. Stereo switching using a standard footswitch is another possible option.
Features:
  • Compact low profile size
  • Standard DIL spacing for easy PCB use and breadboard compatibility
  • Latching
  • Single Coil
  • 5V Coil Voltage

For a non-latching version, please see P-RP-TQ2-5V.
$3.95
IC Socket - Dual in-line package, 2.54mm Pitch, 7.62mm Spacing
IC component sockets for dual in-line package chips (DIP, PDIP, DIL, DIPP.) These sockets feature ladder style cases with tinned stamped and formed connections.
Starting at $0.15
Transistor Socket - Cinch, 3 Pin, Phenolic, NOS
New-old-stock transistor sockets made by Cinch. These three pin phenolic sockets offer a more secure hold than the standard machine-pin transistor sockets of today. They can fit a variety of different transistor package sizes. The flat solder lugs can work in point to point builds or in PCBs with appropriate footprints.
$0.75
Resistors - ¼ Watt, Carbon Film, 5% tolerance
Package of 5
Carbon Film resistors are made by vacuum depositing a thin carbon film on a ceramic form. A good choice for applications which require a steady, low power drop. Package of 5. These resistors are perfect for pedal builders!
  • 1/4 watt
  • ± 5% tolerance
  • EIA color coded
  • .24" long x .08" diameter
  • Package of 5
$1.72
Resistors - ⅛ Watt, Metal Film, 1% tolerance
Package of 5
Metal Film resistors consist of a resistive element of an extremely thin layer of metal alloy vacuum deposited on a substrate. Precise and quiet. These 1/8W resistors have a very small body and are great for tight builds.
$0.65
Resistors - ¼ Watt, Metal Film, 1% tolerance
Package of 5
Metal Film resistors consist of a resistive element of an extremely thin layer of metal alloy vacuum deposited on a substrate. Precise and quiet. Package of 5. These resistors are perfect for pedal builders! 1/4 watt.
$1.80
Potentiometer Adapter Sleeve - Converts 6mm or 18T shaft to ¼"
This brass adapter sleeve converts a 6mm shaft potentiometer or 18T knurled shaft potentiometer to 1/4" shaft (6.35mm), allowing for 1/4" knobs to be used on a wider range of potentiometers. 1/4" tall.
$0.53
Potentiometer - Alpha, 300kΩ, Linear, Knurled Shaft, 16mm
Miniature Alpha pot for guitars. 300K linear taper.
$1.50
Potentiometer - Alpha, Audio, Solid Shaft, 16mm
16mm solid shaft audio potentiometers. These pots are a great for any project. The smaller size is useful for builds with limited panel space such as guitar pedals, synthesizer modules, and adding modifications to equipment. Washer and nut included.
  • Threading: M7 x 0.75
  • Distance between terminals: 5 mm (0.197”)
  • Busing Length: 6.5mm (0.256")
  • Shaft Diameter: 6.35mm ( 0.250")
  • Taper: Audio (Log)
Starting at $1.25
Potentiometer - Alpha, Audio, Solid Shaft, PC Lead, 16mm
Alpha Mini Pots with solid shaft and short PC mount terminals.
  • Threading: M7 x 0.75
  • Distance between terminals: 5 mm (0.197”)
  • Lead Depth from Panel: 3.8 mm (0.150”)
  • Lead Distance from shaft center: 12.5 mm + 3.5 mm (0.492” + 0.138”)
  • Lead Thickness: 0.5 mm (0.020”)
$1.10
Potentiometer - Alpha, Audio, Solid Shaft, Long PC Lead, 16mm
Alpha Mini Pots with solid shaft and long PC mount terminals.
  • Threading: M7 x 0.75
  • Distance between terminals: 5 mm (0.197”)
  • Lead Depth from Panel: 10.7 mm + 5 mm (0.421” + 0.197”)
  • Lead Distance from shaft center: 16 mm (0.630”)
  • Lead Thickness: 0.5 mm (0.020”)
$1.10
Potentiometer - Alpha, Linear, Solid Shaft, 16mm
16mm solid shaft linear potentiometers. These pots are a great for any project. The smaller size is useful for builds with limited panel space such as guitar pedals, synthesizer modules, and adding modifications to equipment. Washer and nut included.
  • Threading: M7 x 0.75
  • Distance between terminals: 5 mm (0.197”)
  • Busing Length: 6.5mm (0.256")
  • Shaft Diameter: 6.35mm ( 0.250")
  • Taper: Linear
$1.25