You are here

Potentiometers

Potentiometers are used to control volume and tone. A potentiometer is a three-terminal resistor with a sliding or rotating contact that forms an adjustable voltage divider.
Check out our Tech Corder articles on pots, including Potentiometer Types.

Filter these results
Sort By:
products per page
View Mode: List View · Grid View
R-VPMT-DMTXPotentiometer - PMT, Dual Mode Tone Control

The DMT is a passive dual mode guitar tone control designed specifically for electric guitars that can operate in either HIGH PASS or LOW PASS modes greatly expanding the instruments tonal possibilities without the use of a battery or active electronics. Micro switches on the circuit board provide the user the ability to select one of two different frequency ranges for both high and low pass modes. Easy installation with no capacitors or other parts needed. Replace the tone control in you guitar with one that you will actually use!


Starting at $19.50
Click to read more
R-VPMT-HCPPotentiometer - PMT, Humbucker Control, Coil Filters

The HCP Humbucker Control Pot is a dual mode variable coil tap selector for electric guitars and basses that eliminates the additional switches associated with coil splitting a pair of humbuckers. In TAP mode, rotating the pot counterclockwise fades from humbuckers to outer coils (neck pickup South coil & bridge pickup North coil). Pulling the HCP control up and rotating it counterclockwise fades from humbuckers to inner coils (neck pickup North coil & bridge pickup South coil). Tonal control is expanded with the unique ability to coil tap both humbuckers in varying amounts. In COIL FILTER mode, turning the HCP control applies varying amounts of a specially tuned high frequency filter to only one coil of the selected coils of the humbuckers (either North or South coils can be filtered). This makes each pickup a single coil at high frequencies and a humbucker at lower frequencies which produces a sound similar to a pair of single coils but with a stronger, fuller tone and 50% less noise than coil tapping.


$22.75
Click to read more
R-VPMT-VTB250XPotentiometer - PMT, V-Treb, Audio Treble Bleed, ⅜" shaft

Precision Music Technologies V-Treb with 250KA course splined pot – Variable Treble Bleed Bypass Circuit. Made in USA. The V-Treb variable treble bleed/bypass circuit corrects the problem of high frequency losses at reduced volumes by allowing the player to control how bright or warm the tone will get as the volume control is reduced. Available in either course or fine settings


$15.50
Click to read more
R-VPMT-VTC500LPotentiometer - PMT, Audio, Variable Treble Bleed, ¾"

Precision Music Technologies V-Treb with 500KA CTS pot – Variable Treble Bleed Bypass Circuit. Made in USA. The V-Treb variable treble bleed/bypass circuit corrects the problem of high frequency losses at reduced volumes by allowing the player to control how bright or warm the tone will get as the volume control is reduced. Pot: 24 mm body diameter, ¼” knurled split shaft. Bushing diameter = 3/8”, Bushing Length = 3/4”. PCB dimentions: 1.06” x 0.46” x 0.07”


$15.75
Click to read more
R-VPMT-VTCXPotentiometer - PMT, CTS, Audio, Variable Treble Bleed, ⅜"

The V-Treb Variable Treble Bleed Circuit for guitar and bass is available pre-installed on high quality volume pots from CTS and Bourns. The circuit corrects the problem of high frequency losses at reduced volumes by allowing the player to control how bright or warm the tone will get as the volume control is reduced. Turning the trim pot clockwise increases the amount of treble bypass for a brighter sound at reduced volumes. Turning the trim pot counter clockwise reduces the amount of treble bypass for a warmer tone at reduced volumes. With the volume at 10, the V-Treb is removed from the circuit and does not affect the sound. The V-Treb circuit also also available separately for use on any other volume pot.


$15.50
Click to read more
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Potentiometers