Potentiometers

Potentiometers are used to control volume and tone. A potentiometer is a three-terminal resistor with a sliding or rotating contact that forms an adjustable voltage divider.Check out our Tech Corder articles on pots, including Potentiometer Types.
Nut - Fender, Hex Type, for Potentiometers
Package of 12
Hex nut for Fender® potentiometers. Package of 12.
$4.45
Potentiometer - Dunlop, MXR, 47K, PC mount
Genuine Dunlop replacement potentiometer for Dunlop/ MXR pedals. PC mount, 47K audio taper, knurled shaft.
$3.15
Potentiometer - PMT, Dual Mode Tone Control
The DMT is a passive dual mode guitar tone control designed specifically for electric guitars that can operate in either HIGH PASS or LOW PASS modes greatly expanding the instruments tonal possibilities without the use of a battery or active electronics. Micro switches on the circuit board provide the user the ability to select one of two different frequency ranges for both high and low pass modes. Easy installation with no capacitors or other parts needed. Replace the tone control in you guitar with one that you will actually use!
Starting at $19.50
Potentiometer - Dunlop Hot Potz, 470 kΩ
Used in Jimi Hendrix's WAH and Dunlop volume pedal. 470 kΩ. Original Dunlop replacement part.
$23.50
Potentiometer - Fender®, S-1, Knurled Shaft, 4PDT
The Fender® S-1™ switched pot is a stealthy way to mod a strat without drilling any extra holes. The switch can be configured for almost any configuration with its four double-throw poles. S-1™ pots use a 3/8” bushing.
$24.95
Nut - for Marshall, Hex Type, M9, for Potentiometers
Package of 5
Replacement nut for Marshall snap in style pots with M9 bushing.
$0.75
Potentiometer - Peavey, 100kΩ, Dual, Bracket
100K Dual Reverse Audio with bracket.
$3.95
Potentiometer - Bourns, 500kΩ Audio, Knurled, Dual Mini
Bourns Mini Carbon Element, DPDT Push Pull Switch, Dual Audio, Split Shaft. ¼" watt, 300° rotation. Solder lugs.
  • 17mm Body Diameter
  • 300° rotation
  • Power Rating: 0.1 watt
  • ¼" Knurled 18-Spline Split Shaft
  • DPDT Push-Pull Switch
  • ⅜" Bushing Length
  • Tolerance: ±20 %
  • Maximum Operating Voltage: 150V
  • Bourns Series Number PDB183-GTR21
$7.95
Potentiometer - Fender, 250K, Solid Shaft, No Load
250K ohm, solid shaft, no load. Some Fender guitars have a unique tone circuit that features a "Delta Tone" Control. The "Delta Tone" system consists of a high output bridge pickup and special 'no-load' tone control for the middle and bridge pickups. This new pot has a detent at the 10 position which bypasses completely any filtration through capacitors. Unlike the TBX, which has a detent at the 5 position and gradually reduces the amount of filtration through the capacitor, the Delta-Tone's 'no-load' feature eliminates filtration completely at the detent and the result is more of the direct presence of the pickup.
$7.45
Potentiometer - Fender®, 500kΩ, Audio, Solid Shaft
500K ohm (audio taper), solid shaft. Made in Taiwan.
$6.95
$7.95
Potentiometer - Bourns, Linear, Knurled Shaft, square
Potentiometer - Bourns, Linear Taper, Knurled Split Shaft, Premium
$9.95
Potentiometer - GØRVA, Audio, 16mm, Right Angle PCB, Solid Shaft
High-quality pcb mount audio taper 16mm pots from Gorva Design. Gorva Design left no boxes unchecked when engineering their potentiometer lineup. Every element was carefully designed to offer builders an exceptional potentiometer with high durability and tight tolerances. Gorva potentiometers are made with stompboxes in mind but offer the same advantages to amplifiers, synthesizers, studio equipment and other electronics.
  • Right-angle PCB mount
  • Audio taper
  • +/- 10% tolerance
  • ¼” (6.35mm) solid shaft
  • Machine-pressed dust seal
  • High quality wiper material
  • Low residual resistance

For linear taper right-angle PCB mount pots see R-VGORVA-BX-PC. For audio taper solder lug pots see R-VGORVA-AX-SL. For linear taper solder lug pots see R-VGORVA-BX-SL.
$1.45
Potentiometer - Fender®, 1M, Solid Shaft
1M ohm, Solid Shaft. Original Fender. Used for Volume and Tone control in many Fender guitars as well as amplifiers.
$5.85
Potentiometer - PMT, Humbucker Control, Coil Filters
The HCP Humbucker Control Pot is a dual mode variable coil tap selector for electric guitars and basses that eliminates the additional switches associated with coil splitting a pair of humbuckers. In TAP mode, rotating the pot counterclockwise fades from humbuckers to outer coils (neck pickup South coil & bridge pickup North coil). Pulling the HCP control up and rotating it counterclockwise fades from humbuckers to inner coils (neck pickup North coil & bridge pickup South coil). Tonal control is expanded with the unique ability to coil tap both humbuckers in varying amounts. In COIL FILTER mode, turning the HCP control applies varying amounts of a specially tuned high frequency filter to only one coil of the selected coils of the humbuckers (either North or South coils can be filtered). This makes each pickup a single coil at high frequencies and a humbucker at lower frequencies which produces a sound similar to a pair of single coils but with a stronger, fuller tone and 50% less noise than coil tapping.
$22.75
Potentiometer - Fender®, 250kΩ, Pan, MN Taper, Solid Shaft
Genuine Fender® 250K pan pot with center detent. Pan pots are also known as balance pots. Solid shaft with 3/8” bushing. Mounting hardware not included. See R-VNUT-38 for a compatible nut and washer.
$4.95
On Backorder
Potentiometer - 100kΩ, Wah Replacement, Life, Smooth
100K Life Pot is a high grade Wah pot replacement. This wah pedal upgrade is sold with all necessary hardware and gear for immediate installation.
$11.95
Potentiometer - Peavey, 50K, Linear, Switch
50K Linear, with push/pull switch. Mounting hardware not included.
$12.95
Potentiometer - GØRVA, Linear, 16mm, Right Angle PCB, Solid Shaft
High-quality pcb mount linear taper 16mm pots from Gorva Design. Gorva Design left no boxes unchecked when engineering their potentiometer lineup. Every element was carefully designed to offer builders an exceptional potentiometer with high durability and tight tolerances. Gorva potentiometers are made with stompboxes in mind but offer the same advantages to amplifiers, synthesizers, studio equipment and other electronics.
  • Right-angle PCB mount
  • Linear taper
  • +/- 10% tolerance
  • ¼” (6.35mm) solid shaft
  • Machine-pressed dust seal
  • High quality wiper material
  • Low residual resistance

For audio taper right-angle PCB mount pots see R-VGORVA-AX-PC. For audio taper solder lug pots see R-VGORVA-AX-SL. For linear taper solder lug pots see R-VGORVA-BX-SL.
$1.45
Potentiometer - Dunlop, Super Pot, Solid Shaft, 250kΩ
The Super Pots from Dunlop are high quality, high performance, volume and tone pots designed and built to last a lifetime. These pots are resistant to dust and corrosion so they will provide smooth performance without the noise and scratchiness associated with normal run of the mill pots. Dunlop tested these pots past the 7 million turn mark. With results like that, these may be the last pots you ever have to put in your instrument.
  • 250K Audio taper
  • Solid shaft
  • Proprietary technology
  • Resistant to dust and corrosion
$13.95
Nut & Washer - Panel, for ⅜" Potentiometers and Jacks
Package of 100
Replacement nut and washer for pots and jacks that feature a ⅜" bushing with 3/8-32 threading. Sold in packs containing 100 nuts and 100 washers.
$25.00
Potentiometer - GØRVA, Linear, 16mm, Solder Lug, Solid Shaft
High-quality solder lug linear taper 16mm pots from Gorva Design. Gorva Design left no boxes unchecked when engineering their potentiometer lineup. Every element was carefully designed to offer builders an exceptional potentiometer with high durability and tight tolerances. Gorva potentiometers are made with stompboxes in mind but offer the same advantages to amplifiers, synthesizers, studio equipment and other electronics.
  • Solder lug / panel mount
  • Linear taper
  • +/- 10% tolerance
  • ¼” (6.35mm) solid shaft
  • Machine-pressed dust seal
  • High quality wiper material
  • Low residual resistance

For audio taper solder lug pots see R-VGORVA-AX-SL. For audio taper right-angle PCB mount pots see R-VGORVA-AX-PC. For linear taper right-angle PCB mount pots see R-VGORVA-BX-PC.
$1.45
Potentiometer - PMT, CTS, Audio, Variable Treble Bleed, ⅜"
The V-Treb Variable Treble Bleed Circuit for guitar and bass is available pre-installed on high quality volume pots from CTS and Bourns. The circuit corrects the problem of high frequency losses at reduced volumes by allowing the player to control how bright or warm the tone will get as the volume control is reduced. Turning the trim pot clockwise increases the amount of treble bypass for a brighter sound at reduced volumes. Turning the trim pot counter clockwise reduces the amount of treble bypass for a warmer tone at reduced volumes. With the volume at 10, the V-Treb is removed from the circuit and does not affect the sound. The V-Treb circuit also also available separately for use on any other volume pot.
$15.50
Potentiometer - Bourns, Linear, Knurled, Conductive Polymer
Linear, .75" bushing length. Conductive polymer, 0.625" W x 0.625" L x 0.5" D body. ¼" watt, 300° rotation. ¼" shaft diameter. Solder lugs. 3/8" bushing. Knurled split shaft.
Starting at $7.50
Save 27%
Originally: $10.25