Potentiometers

Bourns 3352 - ⅜” Round Trimpot. This 1KΩ trimmer features a vertical PCB mount.
Features

• Single-Turn / Cermet / Industrial / Open Frame
• Stable cermet element offers infinite resolution
• Very low profile
• 3352K pin style
• Thumb and screwdriver adjustment
  

100K Dual Reverse Audio with bracket.

Original Fender solid shaft 250K potentiometer with J taper. 3/8-32 threading. The resistance between wiper and cold lug measures about 25% at half-way shaft rotation.

Genuine Fender® replacement 3 Meg Ω potentiometer with a reverse audio taper. This snap in bracketed pot is used as the tremolo speed control pot in many Fender reissue amps that use PCBs for the front panel controls. Mounting hardware not included.

250K ohm, solid shaft, no load. Some Fender guitars have a unique tone circuit that features a "Delta Tone" Control. The "Delta Tone" system consists of a high output bridge pickup and special 'no-load' tone control for the middle and bridge pickups. This new pot has a detent at the 10 position which bypasses completely any filtration through capacitors. Unlike the TBX, which has a detent at the 5 position and gradually reduces the amount of filtration through the capacitor, the Delta-Tone's 'no-load' feature eliminates filtration completely at the detent and the result is more of the direct presence of the pickup.

100K Life Pot is a high grade Wah pot replacement. This wah pedal upgrade is sold with all necessary hardware and gear for immediate installation.

Peavey 20K S-Taper Potentiometer, Spider Style PC Mount Terminals

• Body Diameter: 16mm
• Bushing Diameter: 7mm
• Bushing Length: 5mm
• Shaft Diameter:4.5mm
• Shaft Length:10mm
• Shaft Material: Aluminum – Knurled Split Shaft

Pot, Solid Shaft, 1M J Taper

The DMT is a passive dual mode guitar tone control designed specifically for electric guitars that can operate in either HIGH PASS or LOW PASS modes greatly expanding the instruments tonal possibilities without the use of a battery or active electronics. Micro switches on the circuit board provide the user the ability to select one of two different frequency ranges for both high and low pass modes. Easy installation with no capacitors or other parts needed. Replace the tone control in you guitar with one that you will actually use!

DPDT switch, ¼" split knurled shaft, audio taper. 3/8-32 threads, 16mm body diameter. .75" bushing length, .38"-.52" shaft length.

Linear, .75" bushing length. Conductive polymer, 0.625" W x 0.625" L x 0.5" D body. ¼" watt, 300° rotation. ¼" shaft diameter. Solder lugs. 3/8" bushing. Knurled split shaft.

The V-Treb Variable Treble Bleed Circuit for guitar and bass is available pre-installed on high quality volume pots from CTS and Bourns. The circuit corrects the problem of high frequency losses at reduced volumes by allowing the player to control how bright or warm the tone will get as the volume control is reduced. Turning the trim pot clockwise increases the amount of treble bypass for a brighter sound at reduced volumes. Turning the trim pot counter clockwise reduces the amount of treble bypass for a warmer tone at reduced volumes. With the volume at 10, the V-Treb is removed from the circuit and does not affect the sound. The V-Treb circuit also also available separately for use on any other volume pot.

The HCP Humbucker Control Pot is a dual mode variable coil tap selector for electric guitars and basses that eliminates the additional switches associated with coil splitting a pair of humbuckers. In TAP mode, rotating the pot counterclockwise fades from humbuckers to outer coils (neck pickup South coil & bridge pickup North coil). Pulling the HCP control up and rotating it counterclockwise fades from humbuckers to inner coils (neck pickup North coil & bridge pickup South coil). Tonal control is expanded with the unique ability to coil tap both humbuckers in varying amounts. In COIL FILTER mode, turning the HCP control applies varying amounts of a specially tuned high frequency filter to only one coil of the selected coils of the humbuckers (either North or South coils can be filtered). This makes each pickup a single coil at high frequencies and a humbucker at lower frequencies which produces a sound similar to a pair of single coils but with a stronger, fuller tone and 50% less noise than coil tapping.

50K Linear, spider. Center detent. See R-VPV-50KL-R for a version without detent. Mounting hardware not included.

50K Linear, with push/pull switch. Mounting hardware not included.

50K Linear, wire wound, XL shaft. 30 detents evenly-spaced throughout its rotation. Mounting hardware not included.

Reverse audio taper (antilog), right angle, Alpha pots with a 6.35mm shaft diameter. These 9mm pots are poplar in DIY guitar pedals, synthesizers, and other projects. Mounting nut and washer included.

Replacement nut and washer for pots and jacks that feature a ⅜" bushing with 3/8-32 threading. Sold in packs containing 100 nuts and 100 washers.

250K ohm (audio taper), push-pull DPDT, split shaft. Made in Korea.

Precision Music Technologies V-Treb with 500KA CTS pot – Variable Treble Bleed Bypass Circuit. Made in USA. The V-Treb variable treble bleed/bypass circuit corrects the problem of high frequency losses at reduced volumes by allowing the player to control how bright or warm the tone will get as the volume control is reduced. Pot: 24 mm body diameter, ¼” knurled split shaft. Bushing diameter = 3/8”, Bushing Length = 3/4”. PCB dimentions: 1.06” x 0.46” x 0.07”

• DPDT Push-Push switch
• ¼" split knurled shaft
• Linear taper
• 3/8-32 threads
• 16mm body diameter (widest point on switch body 17.8mm)
• 75" bushing length
• 38"-.52" shaft length.

250 kΩ gear shaft pot with an audio taper. Original Dunlop replacement part. Used in the Dunlop GCB80 High Gain Volume Pedal.

Precision Music Technologies V-Treb – Variable Treble Bleed Bypass Circuit. Made in USA. The V-Treb variable treble bleed/bypass circuit corrects the problem of high frequency losses at reduced volumes by allowing the player to control how bright or warm the tone will get as the volume control is reduced.

10K Audio, 100mm. Pin spacing: 4.870" x 0.191".