Potentiometers

Potentiometers are used to control volume and tone. A potentiometer is a three-terminal resistor with a sliding or rotating contact that forms an adjustable voltage divider.Check out our Tech Corder articles on pots, including Potentiometer Types.
Potentiometer - Fender®, 1M, Solid Shaft
1M ohm, Solid Shaft. Original Fender. Used for Volume and Tone control in many Fender guitars as well as amplifiers.
$5.85
Potentiometer - Fender®, 1MΩ, J Taper, Control, Snap-In
Original Fender® snap-in, control potentiometer, 1 meg, J taper.
$4.15
Potentiometer - Fender®, 250kΩ, Audio, Knurled Shaft
250K ohm, audio taper. for most Stratocasters and Telecasters. Original guitar hardware. CTS manufactured, includes capacitor. Comes in Fender ® packaging.
$6.95
Potentiometer - Fender®, 250kΩ, J Taper, Solid Shaft, Control
Original Fender solid shaft 250K potentiometer with J taper. 3/8-32 threading. The resistance between wiper and cold lug measures about 25% at half-way shaft rotation.
$7.95
Potentiometer - Fender®, 250kΩ, Knurled Shaft, No Load
250K ohm. for most Stratocasters and Telecasters. Original guitar hardware. CTS manufactured, includes capacitor. Comes in Fender ® packaging. Some Fender guitars have a unique tone circuit that features a "Delta Tone' Control. The "Delta Tone' system consists of a high output bridge pickup and special 'no-load' tone control for the middle and bridge pickups. This new pot has a detent at the 10 position which bypasses completely any filtration through capacitors.
$7.45
Potentiometer - Fender®, 250kΩ, Knurled Shaft, Push-Pull
250K ohm (audio taper), push-pull DPDT, split shaft. Made in Korea.
$7.45
Potentiometer - Fender®, 250kΩ, Pan, MN Taper, Solid Shaft
Genuine Fender® 250K pan pot with center detent. Pan pots are also known as balance pots. Solid shaft (1/4") with 3/8” bushing. Mounting hardware not included. See R-VNUT-38 for a compatible nut and washer.
$4.95
Potentiometer - Fender®, 250kΩ, Solid Shaft
250K ohm, solid shaft. for most Stratocasters and Telecasters. Original guitar hardware. CTS manufactured, includes capacitor. Comes in Fender® packaging.
$6.95
Potentiometer - Fender®, 250kΩ, Tone Control, for Tele / Strat
250 kΩ ohm. Original TBX tone control for most Strats and Teles. CTS manufactured, includes capacitor and comes in original Fender® packaging. Some instruments have a unique tone circuit that features a TBX Tone Control (Patented). The TBX (which stands for Treble Bass Expander), is a dual concentric stacked tone pot. The pot has a detent in the middle position. From 0 to 5 (at the detent), the TBX functions like a normal tone circuit with filtration through a capacitor. Advancing the knob counterclockwise from the detent position gradually filters off high frequencies, like a standard tone control. Rotate the knob clockwise from the detent position, and you add presence and brightness by allowing the pickups' natural resonance to come through. Fender part number: 099-2052-000
$12.65
Potentiometer - Fender®, 500kΩ, Audio, Solid Shaft
500K ohm (audio taper), solid shaft. Made in Taiwan.
$6.95
Potentiometer - Fender®, Audio, for Blues Junior
Genuine Fender® replacement potentiometers with audio tapers for Blues Junior models.
  • 250 kΩ - Treble tone control
  • 1 MΩ - Volume

For linear taper pots for the BLues Junior, please see R-VBJ-XL.
Starting at $3.50
Potentiometer - Fender®, S-1, Knurled Shaft, 4PDT
The Fender® S-1™ switched pot is a stealthy way to mod a strat without drilling any extra holes. The switch can be configured for almost any configuration with its four double-throw poles. S-1™ pots use a 3/8” bushing.
$24.95
Potentiometer - GØRVA, Audio, 16mm, Right Angle PCB, Solid Shaft
High-quality pcb mount audio taper 16mm pots from Gorva Design. Gorva Design left no boxes unchecked when engineering their potentiometer lineup. Every element was carefully designed to offer builders an exceptional potentiometer with high durability and tight tolerances. Gorva potentiometers are made with stompboxes in mind but offer the same advantages to amplifiers, synthesizers, studio equipment and other electronics.
  • Right-angle PCB mount
  • Audio taper
  • +/- 10% tolerance
  • ¼” (6.35mm) solid shaft
  • Machine-pressed dust seal
  • High quality wiper material
  • Low residual resistance

For linear taper right-angle PCB mount pots see R-VGORVA-BX-PC. For audio taper solder lug pots see R-VGORVA-AX-SL. For linear taper solder lug pots see R-VGORVA-BX-SL.
$1.45
Potentiometer - GØRVA, Audio, 16mm, Solder Lug, Solid Shaft
High-quality solder lug audio taper 16mm pots from Gorva Design. Gorva Design left no boxes unchecked when engineering their potentiometer lineup. Every element was carefully designed to offer builders an exceptional potentiometer with high durability and tight tolerances. Gorva potentiometers are made with stompboxes in mind but offer the same advantages to amplifiers, synthesizers, studio equipment and other electronics.
  • Solder lug / panel mount
  • Audio taper
  • +/- 10% tolerance
  • ¼” (6.35mm) solid shaft
  • Machine-pressed dust seal
  • High quality wiper material
  • Low residual resistance

For linear taper solder lug pots see R-VGORVA-BX-SL. For audio taper right-angle PCB mount pots see R-VGORVA-AX-PC. For linear taper right-angle PCB mount pots see R-VGORVA-BX-PC.
$1.45
Potentiometer - GØRVA, Linear, 16mm, Right Angle PCB, Solid Shaft
High-quality pcb mount linear taper 16mm pots from Gorva Design. Gorva Design left no boxes unchecked when engineering their potentiometer lineup. Every element was carefully designed to offer builders an exceptional potentiometer with high durability and tight tolerances. Gorva potentiometers are made with stompboxes in mind but offer the same advantages to amplifiers, synthesizers, studio equipment and other electronics.
  • Right-angle PCB mount
  • Linear taper
  • +/- 10% tolerance
  • ¼” (6.35mm) solid shaft
  • Machine-pressed dust seal
  • High quality wiper material
  • Low residual resistance

For audio taper right-angle PCB mount pots see R-VGORVA-AX-PC. For audio taper solder lug pots see R-VGORVA-AX-SL. For linear taper solder lug pots see R-VGORVA-BX-SL.
$1.45
Potentiometer - GØRVA, Linear, 16mm, Solder Lug, Solid Shaft
High-quality solder lug linear taper 16mm pots from Gorva Design. Gorva Design left no boxes unchecked when engineering their potentiometer lineup. Every element was carefully designed to offer builders an exceptional potentiometer with high durability and tight tolerances. Gorva potentiometers are made with stompboxes in mind but offer the same advantages to amplifiers, synthesizers, studio equipment and other electronics.
  • Solder lug / panel mount
  • Linear taper
  • +/- 10% tolerance
  • ¼” (6.35mm) solid shaft
  • Machine-pressed dust seal
  • High quality wiper material
  • Low residual resistance

For audio taper solder lug pots see R-VGORVA-AX-SL. For audio taper right-angle PCB mount pots see R-VGORVA-AX-PC. For linear taper right-angle PCB mount pots see R-VGORVA-BX-PC.
$1.45
Potentiometer - Linear, 16mm, Marshall Style
Marshall style linear taper 16mm potentiometer with 7mm bushing. Knurled split shaft.
$1.50
Potentiometer - Linear, D Shaft, 16mm, Snap-In, Bracket
Linear. 16mm body size (mini type) Snap-In pot with mounting bracket. D-Shaft ¼", ½" length shaft. 7mm bushing, ¼" bushing length. PC Mount. Nut and washer included
$1.40
Potentiometer - Linear, Solid Shaft, Snap-In, Bracket
Linear. 16mm body size (mini type) Snap-In pot with mounting bracket. Solid Shaft ¼", ⅜" length shaft. 8mm bushing, ¼" bushing length. PC Mount. Nut and washer included.
$1.50
Potentiometer - Marshall, 10 kΩ, 9mm
Genuine Marshall replacement potentiometer for MG Series amps. 10 kΩ Linear, D-Shaft.
$5.95
Potentiometer - Marshall, 10kΩ, Linear, Dual, 16mm
10K dual linear, 16mm, 7mm bushing.
$3.95
Potentiometer - Marshall, 22kΩ, Linear, Bias, for JMP
22kΩ linear taper. Used as bias / trim potentiometer for JMP.
For a same-brand generic replacement, see R-V25KV-BP.
$3.95
Potentiometer - Marshall, Audio, 11mm, PC Mount, Square
Audio taper square body PC mount potentiometer by Marshall. Body width = 11mm
See R-VKG-XL for the Linear taper equivalent
$4.95
Partially Out of Stock
Potentiometer - Marshall, Linear, 11mm, PC Mount, Square
Linear taper square body PC mount potentiometer by Marshall. Body width = 11mm
See R-VKG-XA for the Audio taper equivalent
$4.95