Potentiometers

Potentiometers are used to control volume and tone. A potentiometer is a three-terminal resistor with a sliding or rotating contact that forms an adjustable voltage divider.Check out our Tech Corder articles on pots, including Potentiometer Types.
Potentiometer - PMT, Dual Mode Tone Control
The DMT is a passive dual mode guitar tone control designed specifically for electric guitars that can operate in either HIGH PASS or LOW PASS modes greatly expanding the instruments tonal possibilities without the use of a battery or active electronics. Micro switches on the circuit board provide the user the ability to select one of two different frequency ranges for both high and low pass modes. Easy installation with no capacitors or other parts needed. Replace the tone control in you guitar with one that you will actually use!
Starting at $19.50
Potentiometer - Fender®, 250kΩ, J Taper, Solid Shaft, Control
Original Fender solid shaft 250K potentiometer with J taper. 3/8-32 threading. The resistance between wiper and cold lug measures about 25% at half-way shaft rotation.
$7.50
On Backorder
Potentiometer - Fender®, 250kΩ, Knurled Shaft, Push-Pull
250K ohm (audio taper), push-pull DPDT, split shaft. Made in Korea.
$12.95
On Backorder
Potentiometer - Bourns, Linear, Knurled, Conductive Polymer
Linear, .75" bushing length. Conductive polymer, 0.625" W x 0.625" L x 0.5" D body. ¼" watt, 300° rotation. ¼" shaft diameter. Solder lugs. 3/8" bushing. Knurled split shaft.
Starting at $8.56
Potentiometer - Peavey, 10kΩ, Audio, Slide, 100mm
10K Audio, 100mm. Pin spacing: 4.870" x 0.191".
$7.50
On Backorder
Potentiometer - PMT, Audio, Variable Treble Bleed, ¾"
Precision Music Technologies V-Treb with 500KA CTS pot – Variable Treble Bleed Bypass Circuit. Made in USA. The V-Treb variable treble bleed/bypass circuit corrects the problem of high frequency losses at reduced volumes by allowing the player to control how bright or warm the tone will get as the volume control is reduced. Pot: 24 mm body diameter, ¼” knurled split shaft. Bushing diameter = 3/8”, Bushing Length = 3/4”. PCB dimentions: 1.06” x 0.46” x 0.07”
$15.75
Potentiometer - Fender, 3M, Reverse Audio, Solid, 16mm, Snap-In
Genuine Fender® replacement 3 Meg Ω potentiometer with a reverse audio taper. This snap in bracketed pot is used as the tremolo speed control pot in many Fender reissue amps that use PCBs for the front panel controls. Mounting hardware not included.
$3.95
On Backorder
Trimmer - CTS, Series 201, Single-Turn, Vertical Mount, 50KΩ
CTS 201 Series trimmer potentiometer. This 50KΩ trimpot features a vertical PCB mount. Features:
  • Miniature size — knob 19/32" (15.08mm) diameter
  • Printed circuit mounting with knob perpendicular to printed circuit board
  • 20% resistance tolerance
  • Knob slotted for screwdriver adjustment
  • Reliable CTS composition resistance element
$1.50
Potentiometer - CTS, Audio, Knurled Shaft, ⅜" Bushing
The 24mm body knurled shaft potentiometer features a 1/3 watt rating and a 3/8" bushing. 24 teeth slot and knurled shaft.
Includes:
  • 1 nut
  • 1 lock washer
$4.50
Potentiometer - CTS, 50kΩ, Reverse Audio
24mm, ½ watt, 3/8" bushing, ¼" splined nylon shaft for set screw or push-on knob. for most US made amps.
$3.25
Potentiometer - CTS, Audio, 1 MΩ, SPST, Push-Pull, Solder Lug
Audio, SPST, solder lugs, ⅜" bushing, 24mm
$8.95
Potentiometer - CTS, 3MΩ, Reverse Audio
24mm, ½" watt, 3/8" bushing, ¼" splined nylon shaft for set screw or push-on knob. for most US made amps.
$3.25
Trimmer - Bourns, 3352K, Single-Turn, Side Adjust, 1KΩ
Bourns 3352 - ⅜” Round Trimpot. This 1KΩ trimmer features a vertical PCB mount.
Features
  • Single-Turn / Cermet / Industrial / Open Frame
  • Stable cermet element offers infinite resolution
  • Very low profile
  • 3352K pin style
  • Thumb and screwdriver adjustment
$1.50
Potentiometer - 500kΩ, Audio, Knurled Shaft, DPDT, Push-Push
DPDT switch, ¼" split knurled shaft, audio taper. 3/8-32 threads, 16mm body diameter. .40" bushing length, .38"-.52" shaft length.
$9.80
On Backorder
Potentiometer - Alpha, Linear, Solid Shaft, 16mm
16mm solid shaft linear potentiometers. These pots are a great for any project. The smaller size is useful for builds with limited panel space such as guitar pedals, synthesizer modules, and adding modifications to equipment. Washer and nut included.
  • Threading: M7 x 0.75
  • Distance between terminals: 5 mm (0.197”)
  • Busing Length: 6.5mm (0.256")
  • Shaft Diameter: 6.35mm ( 0.250")
  • Taper: Linear
$1.25