Power Supplies & Accessories

Fuse Holder - 3AG-Type, High Quality
High quality fuse holder used with 3AG type fuse. Fits in a 1/2" diameter chassis hole. Frame and cap material: phenolic Terminal material: Nickel-plated brass Mounted by nut
$2.06
Cord - Power, 18 AWG, 3 Conductor, Black, Bare End
18AWG SJT power cords used in many amplifiers along with other appliances and equipment. These cords feature bare ends for hard wiring to devices internally or using a connector. The attached plug is a Nema 5-15P for North American grounded outlets. These cords have a maximum voltage rating of 300V.
Starting at $3.95
Strain Relief - for ~\frac{35}{64}~" x ⅝" Hole, ~\frac{11}{32}~" Cord Diameter
For 35/64" x 5/8" chassis hole, 11/32" cord diameter. Fits most Fender® amps.
  • Protects the lifeline of your electric/ electronic products by absorbing the forces of pull, push, and twist that may be exerted on the flexible power cord.
  • Securely anchors, insulates, and protects cables at panel entry points
$0.95
Fuse - Slow-Blow, 250V, Miniature, 5mm x 20mm
Package of 5
Protect your expensive investment or hobby with inexpensive fuses. Time-delay, low breaking capacity. Rated at 250V. Package of 5
$3.50
Fuse - Slow-Blow, 250V, 3AG, 0.25" x 1.25"
Package of 5
The 3AG Slo-Blo fuse solves a broad range of application requirements while offering reliable performance and costeffective circuit protection. Fits fuse block S-H259 and fuse holder S-H201.
$3.25
Power Jack - DC Panel Mount, Rear Mount, 5.5mm External, 2.1mm Internal
½" panel mount DC jack with solder lugs. This jack is rear mounted which makes troubleshooting and repairs simpler since the jack does not need to be desoldered if the circuit needs to be removed from the enclosure. Round plastic with normally closed switch. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Three solder lugs are available for tip, ring, and switch.
$0.59
Cord - Power, 16 AWG, 3 Conductor, Black
Power Cord / cable - (3 conductor) Bare End, 16 AWG
Starting at $5.95
Strain Relief - Nylon, 0.12" x 0.22" Wire (SPT-1)
Two conductor, nylon, .12" x .22" wire (SPT-1). Protects the lifeline of your electric/electronic products by absorbing the forces of pull, push, and twist that may be exerted on flexible power cords. Securely anchors, insulates, and protects cable at panel entry points.
$0.50
Grommet - Rubber, for Reverb Tank vibration
Package of 4
Mount these rubber grommets to the base of reverb tanks to help alleviate feedback and other vibration issues. The thick rubber ring helps with isolating the tank from the surface that it is mounted to or resting upon. These rubber grommets fit typical reverbs tanks. Mounting Hole Diameter = 3/8" Outer Diameter = 1/2". Package of 4.
$1.30
PCB - Daughterboard for Wiring 3PDT Footswitches
Our 3PDT PCB daughterboard is a small board designed to simplify the wiring of 3PDT footswitches in guitar pedals. All inputs and outputs are clearly labeled on the PCB, removing any confusion about how the footswitch should be wired, and decreasing the chances of wiring mistakes or short-circuits.
$0.75
Power Jack - DC Panel Mount, Low Profile, 5.5mm External, 2.1mm Internal
Low profile DC jack with solder lugs. This jack is the perfect size for smaller builds where additional space is necessary. The low profile DC jack is also great for builds where aesthetics are a priority. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Features two solder lugs for tip and ring.
$0.59
Grommet - Rubber, for chassis holes
Package of 5
Listed diameter is inside diameter. Sold in packs of 5.
  • 3/8" diameter designed for chassis hole with diameter 1/2"
  • 1/8" diameter designed for chassis hole with diameter 1/4"
  • 3/16" diameter designed for chassis hole with diameter 5/16"
  • 1/4", small cutout diameter designed for chassis hole with diameter 7/16"
  • 1/4" diameter designed for chassis hole with diameter 7/16"
  • 5/16" diameter designed for chassis hole with diameter 7/16"
Starting at $0.95
Fuse - Fast-Blow, 250V, 3AG, 0.25" x 1.25"
Package of 5
Protect your expensive investment or hobby with inexpensive fuses.
Starting at $2.25
Power Jack - DC PC Mount, 5.5mm External, 2.1mm Internal
This PCB mounted DC jack style can be found on many manufacturers’ pedals. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Three solder pins are available for tip, ring, and switch.
$0.59
Power Jack - DC Panel Mount, 5.5mm External, 2.1mm Internal
Colors Available:
½" panel mount with solder lugs. Round plastic with normally closed switch. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter.
$0.95
Receptacle - AC, Mates with S-W123 & S-W124 with Fuse Holder
I.E.C. Power Cord Receptacle. Mates with power cords S-W123 and S-W124. Rated for 6A, 250V. UL listed. Compatible with GMA fuses
$1.85
Receptacle - AC power plug with fuse holder, 10A, 250VAC
Black plastic AC power entry module with built in fuse holder. This power entry module is rated at 10A, 250VAC and fits 5mm x 20mm fuses. Mates with S-W123 & S-W124
$1.25
Fuse Holder - for Marshall, ¼" Fuses
Fuse Holder - High Quality Marshall Snap-In Style (Fits 5/8" to 11/16" Chassis Holes). Suitable for 1/4" fuses. UL and CSA approved. Electrical Specifications:
  • Rated current: 10A
  • Rated voltage: 250V AC
  • Contact resistance: 2MΩ @ 250V DC or less
  • Dialectric withstand: 1 minute @ 1500V AC
  • Insulation resistance: 100MΩ or more @ 500V DC
$5.35
Cord - Replacement Black, Non-Polarized
Black SPT-1 power cable
  • non-polarized
  • tinned leads
  • 6 foot length
  • 18 AWG.
$1.95
Power Jack - DC Panel Mount, Vintage Boss Style, 5.5mm External, 2.1mm Internal
This DC power jack is similar to those used on vintage MIJ Boss pedals and others. This jack has a 2.1mm pin for use with 5.5mm barrel plugs. Three solder lugs are available for tip, ring, and switch.
$0.59
Fuse - Fast-Blow, Miniature, 5mm x 20mm
Package of 5
Protect your expensive investment or hobby with inexpensive fuses. • GMA Type • Measures .78"(20mm) in length, 0.19"(5mm) in diameter • Fast-Blow • Package of 5
$3.25
Strain Relief - Rubber, for ¼" Diameter Hole
Strain relief for wiring - for use in 1/4 diameter hole.
$0.50
Cable Clamp - for ½" Cable Diameter, Nylon
Package of 10
Nylon cable clamp with room for ½” cable outer diameter. Perfect for securing power cords to cabinet walls.
$1.40
Plug - AC, Flat, Brown, vintage style two prong
A new two-prong plug, acceptable as a retro or vintage substitute. The plug easily accepts our twisted 18 and 16 gauge wires (two-conductor only). Wire Opening Diameter: 11.2 mm x 8.4 mm, 7/16" x 5/16" UL Rating: 15A-125V Made in Mexico
$2.75