Power Supplies & Accessories

Fuse Holder - 3AG-Type, High Quality
High quality fuse holder used with 3AG type fuse. Fits in a 1/2" diameter chassis hole. Frame and cap material: phenolic Terminal material: Nickel-plated brass Mounted by nut
$2.06
Power Jack - DC Panel Mount, 5.5mm External, 2.1mm Internal
Colors Available:
New!:
½" panel mount with solder lugs. Round plastic with normally closed switch. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter.
Starting at $0.75
Cord - Power, 18 AWG, 3 Conductor, Detachable, Black, IEC
Three conductor, 8 or 12 foot detachable power cord with IEC female end SVT (Marshall type), 18 awg.
Starting at $5.65
Fuse - Slow-Blow, 250V, 3AG, 0.25" x 1.25"
Package of 5
The 3AG Slo-Blo fuse solves a broad range of application requirements while offering reliable performance and costeffective circuit protection. Fits fuse block S-H259 and fuse holder S-H201.
$3.25
Fuse Holder - for Fender®, 3AG-Type
High quality Fender® Style fuse holder replacement for guitar amplifiers.
  • Fits ½" chassis hole diameter
  • Mounted by Nut
$2.50
Cord - Power, 18 AWG, 3 Conductor, Black, Bare End
18AWG SJT power cords used in many amplifiers along with other appliances and equipment. These cords feature bare ends for hard wiring to devices internally or using a connector. The attached plug is a Nema 5-15P for North American grounded outlets. These cords have a maximum voltage rating of 300V.
Starting at $4.95
Receptacle - IEC C14, for power cord, 3 prong
Plastic IEC C14 connector for power entry. This power receptacle mounts with two screw holes which are counterunk for a clean look when using countersunk screws. This is a 3 prong connector for power cables with ground connections. Internal connections can be soldered into place or used with quick disconnects. See Specifications, Files, and Documents for a datasheet with dimensions and panel cut out sizing.
$1.95
Cord - Power, 16 AWG, 3 Conductor, Black
Power Cord / cable - (3 conductor) Bare End, 16 AWG
Starting at $6.35
Strain Relief - for ~\frac{35}{64}~" x ⅝" Hole, ~\frac{11}{32}~" Cord Diameter
For 35/64" x 5/8" chassis hole, 11/32" cord diameter. Fits most Fender® amps.
  • Protects the lifeline of your electric/ electronic products by absorbing the forces of pull, push, and twist that may be exerted on the flexible power cord.
  • Securely anchors, insulates, and protects cables at panel entry points
$0.95
Fuse - Slow-Blow, 250V, Miniature, GMD-type 5mm x 20mm
Package of 5
Protect your expensive investment or hobby with inexpensive fuses. Time-delay, low breaking capacity. Rated at 250V. Package of 5
$3.50
Grommet - Rubber, for chassis holes
Package of 5
Listed diameter is inside diameter. Sold in packs of 5.
  • 3/8" diameter designed for chassis hole with diameter 1/2"
  • 1/8" diameter designed for chassis hole with diameter 1/4"
  • 3/16" diameter designed for chassis hole with diameter 5/16"
  • 1/4", small cutout diameter designed for chassis hole with diameter 3/8"
  • 1/4" diameter designed for chassis hole with diameter 7/16"
  • 5/16" diameter designed for chassis hole with diameter 7/16"
Starting at $0.95
Power Jack - DC Panel Mount, Rear Mount, 5.5mm External, 2.1mm Internal
½" panel mount DC jack with solder lugs. This jack is rear mounted which makes troubleshooting and repairs simpler since the jack does not need to be desoldered if the circuit needs to be removed from the enclosure. Round plastic with normally closed switch. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Three solder lugs are available for tip, ring, and switch.
$0.59
Power Jack - Lumberg, DC Panel Mount, 5.5mm External, 2.1mm Internal
Lumberg panel mount barrel jack with solder lugs.This DC jack features a normally closed switch on the ring (sleeve) connection. For use with barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Mounting nut included.
$1.15
Cable Clamp - for ¼" Cable Diameter, Nylon
Nylon cable clamp with room for 1/4” cable outer diameter. Perfect for securing cables to cabinet walls. For larger ½” cable clamps see P-HCABLECLAMP-10.
$0.23
Fuse - Fast-Blow, 250V, 3AG, 0.25" x 1.25"
Package of 5
Protect your expensive investment or hobby with inexpensive fuses.
Starting at $2.25
Grommet - Rubber, for Reverb Tank vibration
Package of 4
Mount these rubber grommets to the base of reverb tanks to help alleviate feedback and other vibration issues. The thick rubber ring helps with isolating the tank from the surface that it is mounted to or resting upon. These rubber grommets fit typical reverbs tanks. Mounting Hole Diameter = 3/8" Outer Diameter = 1/2". Package of 4.
$1.30
Power Jack - DC Panel Mount, Low Profile, 5.5mm External, 2.1mm Internal
Low profile DC jack with solder lugs. This jack is the perfect size for smaller builds where additional space is necessary. The low profile DC jack is also great for builds where aesthetics are a priority. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Features two solder lugs for tip and ring.
$0.59
PCB - Daughterboard for Wiring 3PDT Footswitches
Our 3PDT PCB daughterboard is a small board designed to simplify the wiring of 3PDT footswitches in guitar pedals. All inputs and outputs are clearly labeled on the PCB, removing any confusion about how the footswitch should be wired, and decreasing the chances of wiring mistakes or short-circuits.
$0.75
On Backorder
Strain Relief - for ¾" x ~\frac{27}{32}~" hole, ~\frac{5}{16}~" cord diameter
16/3 SJT, 5/16" cord diameter. These one piece Strain Relief Bushings securely anchor, absorb, and protect cables and wires from push/pull and twist forces, while insulating them from irregular or sharp panel edges. They are easily and quickly installed with special installation pliers or other hand or production tools. Black H.S. Nylon, and the temperature index is 105° Centigrade.
$0.85
Cord - Replacement Brown, Polarized Plug
Brown SPT-1 power cable
  • polarized
  • tinned leads
  • 6 foot length
  • 18 AWG
$2.65
Barrel Plug - Cliff, Cable Mount, 5.5mm External, 2.1mm Internal
Genuine Cliff barrel plug for use with 5.5mm / 2.1mm barrel jacks. This plug is great for repairing power supplies and making cables. The outside housing is made of a thick durable plastic.
$1.05
Fuse Block - for 3AB and 3AG fuses, low profile
Open frame fuse holder with patented self-aligning, snap-in terminal clips. A low profile fuse block featuring individual barriers which reinforce the fuse clips while providing greater protection against clip damage and electrical shock. The uniqu design permits self-alignment of clips to fuse cap. This, plus a one-piece clip / terminal assures low contact resistance. Higher current ratings have been attained using spring brass clips.
$3.10
Power Jack - DC Panel Mount, Vintage Boss Style, 5.5mm External, 2.1mm Internal
This DC power jack is similar to those used on vintage MIJ Boss pedals and others. This jack has a 2.1mm pin for use with 5.5mm barrel plugs. Three solder lugs are available for tip, ring, and switch.
$0.59
Power Jack - Lumberg, DC Panel Mount, Low Profile, 5.5mm External, 2.1mm Internal
Low profile Lumberg panel mount barrel jack with solder lugs. This high quality jack is the perfect size for smaller builds where additional space is necessary. The Lumberg low profile DC jack is also great for builds where aesthetics are a priority. For use with barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Mounting nut included.
$1.25
On Backorder