Power Supplies & Accessories
Fuse Holder - 3AG-Type, High Quality
High quality fuse holder used with 3AG type fuse. Fits in a 1/2" diameter chassis hole. Frame and cap material: phenolic Terminal material: Nickel-plated brass Mounted by nut
Fuse Holder - for Fender®, 3AG-Type
High quality Fender® Style fuse holder replacement for guitar amplifiers.
- Fits ½" chassis hole diameter
- Mounted by Nut
Fuse Block - for 3AB and 3AG fuses, low profile
Open frame fuse holder with patented self-aligning, snap-in terminal clips. A low profile fuse block featuring individual barriers which reinforce the fuse clips while providing greater protection against clip damage and electrical shock. The uniqu design permits self-alignment of clips to fuse cap. This, plus a one-piece clip / terminal assures low contact resistance. Higher current ratings have been attained using spring brass clips.
Receptacle - AC with Fuse Holder, mates with S-W123 & S-W124
I.E.C. Power Cord Receptacle. Mates with power cords S-W123 and S-W124. Rated for 6A, 250V. UL listed. Compatible with GMA fuses
Receptacle - IEC C14, Panel Mount, Fuse Holder, 10A, 250VAC
Plastic IEC C14 connector for power entry. This power receptacle mounts with two screw holes which are counterunk for a clean look when using countersunk screws. This is a 3 prong connector for power cables with ground connections. Internal connections can be soldered into place or used with quick disconnects. This receptacle features a built-in fuse holder for 5mm x 20mm fuses. See Specifications, Files, and Documents for a datasheet with dimensions and panel cut out sizing.
Fuse Holder - 3AG-Type, Tweed Style, Solder Lug
Panel mount 3AG fuse holder with solder lug connectors. This fuse holder matches the style of vintage tweed amps and is a great replacement for original amps or new builds. Mounting nut and rubber washer included.
Fuse Holder - Clip, GMA-Type, PCB Mount
Through-hole PCB mounted fuse holder clips found in Peavey amps and other electronics. These small clips allow for minimal space fuse mourning directly on PCB’s. Fits GMA 5×20mm fuses. A pair is required to mount a fuse. Sold individually.
Fuse Holder - 3AG-Type, Low Profile, Knob, Right Angle Spade Lug
Panel mount 3AG fuse holder with spade lug connectors. This fuse holder features a low profile bayonet style knob and reduced overall height. The connector at the end of the holder is right angled which reduces the internal depth as well. It is a similar style to fuse holders used on many Fender® amps. Mounting nut and rubber washer included.
Fuse Holder - 3AG-Type, Low Profile, Slotted, Spade Lug
Panel mount 3AG fuse holder with spade lug connectors. This fuse holder features a low profile slotted cap and reduced overall height. It is a similar style to fuse holders used on many vintage Marshall amps. Mounting nut and rubber washer included.
Receptacle - AC power plug with fuse holder, 10A, 250VAC
Black plastic AC power entry module with built in fuse holder. This power entry module is rated at 10A, 250VAC and fits 5mm x 20mm fuses. Mates with S-W123 & S-W124
Fuse Holder - for Marshall, ¼" Fuses
Fuse Holder - High Quality Marshall Snap-In Style (Fits 5/8" to 11/16" Chassis Holes). Suitable for 1/4" fuses. UL and CSA approved. Electrical Specifications:
- Rated current: 10A
- Rated voltage: 250V AC
- Contact resistance: 2MΩ @ 250V DC or less
- Dialectric withstand: 1 minute @ 1500V AC
- Insulation resistance: 100MΩ or more @ 500V DC
Fuse Holder - 3AG-Type, High Quality, Low Profile
High quality fuse holder used with 3AG type fuse. This fuse holder features a low profile design. This holder used 0.187” (4.8mm) quick connect tabs that can also be soldered to. Mounting nut included. 13.2mm hole required for mounting.
Fuse Holder Cap - Marshall, for 900 Series
Fuse holder cap for Marshall™ 900 series amps. Measures 5/8" in length. Fits into S-H213
Replacement Fuse Holder Cap - For P-SP2-500
Fuse holder cap replacement for P-SP2-500 power receptacle.
Fuse Block - For GMA / GMD Fuses, Low Profile
Open frame fuse block for GMA or GMD 5×20mm size fuses with a low profile design that features solder terminals made of tin plated brass. A unique design feature provides self-alignment of the clips to the fuse caps. This feature, plus a one-piece clip/terminal design, assures low contact resistance.
Fuse Holder Cap - Peavey, top-slotted for screwdriver
Peavey cap for fuse holder. 1 1/16" length x 3/8" diameter. Top slotted for flat head screwdriver.
Fuse Holder - 3AG-Type, Tweed Style, Right Angle Spade Lug
Panel mount 3AG fuse holder with spade lug connectors. This fuse holder matches the style of vintage tweed amps and is a great replacement for original amps or new builds. Mounting nut and rubber washer included.
Note: The spade lugs have a detent rather than a hole.
Note: The spade lugs have a detent rather than a hole.
Fuse Holder Cap - 3AG, Slotted, for Marshall 2000 Series
Fuse holder cap for the fuse holder found on the Marshall® JCM2000 series such as the TSL100, TSL122, DSL50, and DSL100 as well as other amps. This cap fits 3AG fuses and pairs with S-H211.
Fuse Holder - for Marshall, GMA or GMD Type, PCB Mount
Though-hole PCB mount fuse holder used on many Marshall amps such as the 900 series and some 2000 series amps. The fuse cap is sold separately as S-H204. Fits GMA and GMD 5×20mm fuses.
Insulation Cover - Fuse Holder, 15.5 x 36.8mm, PVC
High quality insulation cover for panel mount fuse holders. The cover is made of a thick durable PVC and fits many fuse holders. The wire sleeve can securely fit over any standard wire gauge used with fuse holders providing a fully insulated fuse connection.
- Provides insulation against shock on rear of fuse holder
- UL94V-0 rated flame retardant material
Fuse Holder - Bakelite, Soviet, GMD-type 5mm x 20mm
New-old-stock Soviet fuse holders. These panel mount holders fit 5x20mm GMA and GMD type fuses. A 0.625” mounting hole is required. Note: A small 0.1” notch must either be filed into the 0.625” mounting hole or filed off of the fuse to flush mount with a panel
Fuse Holder - for Marshall, 3AG Type, PCB Mount
Though-hole PCB mount fuse holder used on many Marshall® JCM2000 series such as the TSL100, TSL122, DSL50, and DSL100 as well as other amps. Check footprint and dimensions for compatibility. This holder fits 3AG fuses and pairs with the S-H212 cap. Cap sold separately.
Fuse Cap - PCB Mounting, Universal, GMA
PCB Mount Fuse Cap.
- 1.31” x 0.42”
- Takes GMA sized fuse