Power Supplies & Accessories

Black SPT-1 power cable

• non-polarized
• tinned leads
• 6 foot length
• 18 AWG.

High quality snap-in IEC C14 power entry connector. The connector is easy to install and is rated for 250VAC at 15A. The quick disconnect terminals can also be directly soldered to. Features:

• High quality thermoplastic housing
• Copper alloy terminals (4.8mm width)
• Quick installation
• Fits 0.8mm to 2mm thick panels

Open frame fuse holder with patented self-aligning, snap-in terminal clips. A low profile fuse block featuring individual barriers which reinforce the fuse clips while providing greater protection against clip damage and electrical shock. The uniqu design permits self-alignment of clips to fuse cap. This, plus a one-piece clip / terminal assures low contact resistance. Higher current ratings have been attained using spring brass clips.

9V battery clip with a fiberboard frame. This high quality battery snap features tinned brass eyelets that secure the nickel-plated steel contacts to the fiberboard. Wires can be soldered directly to the eyelets allowing for custom length battery connections. This fiberboard style is similar to the 9V battery connectors in vintage electronics such as the Arbiter Fuzz Face.

Brown SPT-1 power cable

• polarized
• tinned leads
• 6 foot length
• 18 AWG

This DC power jack is similar to those used on vintage MIJ Boss pedals and others. This jack has a 2.1mm pin for use with 5.5mm barrel plugs. Three solder lugs are available for tip, ring, and switch.

High quality chassis mount battery holder. This steel holder fits standard 9V batteries. The horizontal mount and small footprint of the holder allows for easy placement where vertical space is limited.

Panel mount 3AG fuse holder with spade lug connectors. This fuse holder features a low profile bayonet style knob and reduced overall height. The connector at the end of the holder is right angled which reduces the internal depth as well. It is a similar style to fuse holders used on many Fender® amps. Mounting nut and rubber washer included.

16/3 SJT, 5/16" cord diameter. These one piece Strain Relief Bushings securely anchor, absorb, and protect cables and wires from push/pull and twist forces, while insulating them from irregular or sharp panel edges. They are easily and quickly installed with special installation pliers or other hand or production tools. Black H.S. Nylon, and the temperature index is 105° Centigrade.

This PCB mounted DC jack style can be found on many manufacturers’ pedals. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Three solder pins are available for tip, ring, and switch.

Extra heavy duty carbon zinc batteries from GP. The GP Greencell 9V is a favorite for fuzz pedals and is the stock battery for many boutique builders such as D*A*M and others. Additionally, these batteries are a great choice for any low current battery powered pedal or other devices.

½" panel mount DC jack with solder lugs. This jack is rear mounted which makes troubleshooting and repairs simpler since the jack does not need to be desoldered if the circuit needs to be removed from the enclosure. Round plastic with normally closed switch. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Three solder lugs are available for tip, ring, and switch.

High quality chassis mount battery holder. This steel holder fits standard 9V batteries. The vertical mount and small footprint of the holder are great for narrow spaces and work well for any project. See S-H158 for horizontal-mount.

Panel mount 3AG fuse holder with spade lug connectors. This fuse holder features a low profile slotted cap and reduced overall height. It is a similar style to fuse holders used on many vintage Marshall amps. Mounting nut and rubber washer included.

Premium 9V battery clip made of a rigid plastic frame with an insulating wall enclosing the battery terminals. This high quality battery snap features nickel-plated brass contacts. The six inch leads are 26 AWG stranded wire, prestripped and tinned for an easy installation.

3PDT switch mounted charge pump PCB for positive ground effects. This small PCB simplifies the wiring of 3PDT foot switches in guitar pedals while also offering -9V when used with a standard +9V power supply. This is a great option for positive ground effects such as vintage fuzz pedals. The circuit of this PCB also features a protection diode and an LED indicator for when the effect is engaged.
This board is compatible with the MAX1044, TC1044S, TC7660S, and LT1054 charge pump ICs.

I.E.C. Power Cord Receptacle. Mates with power cords S-W123 and S-W124. Rated for 6A, 250V. UL listed. Compatible with GMA fuses

Nylon cable tie mounts with adhesive backing. These mounts easily attach to most surfaces using a strong foam adhesive. Zip ties can be fed through the openings on the mount to secure wires to an enclosure, board, or any other convenient location.

Nylon strain relief for two conductor SPT-1 wire (.11" x .21”). Protects the lifeline of your electric/electronic products by absorbing the forces of pull, push, and twist that may be exerted on flexible power cords. Securely anchors, insulates, and protects cable at panel entry points. Fits 0.375” x 0.345” mounting holes with 0.62” panel thickness.

Panel mount 3AG fuse holder with solder lug connectors. This fuse holder matches the style of vintage tweed amps and is a great replacement for original amps or new builds. Mounting nut and rubber washer included.

Fuse Holder - High Quality Marshall Snap-In Style (Fits 5/8" to 11/16" Chassis Holes). Suitable for 1/4" fuses. UL and CSA approved. Electrical Specifications:

• Rated current: 10A
• Rated voltage: 250V AC
• Contact resistance: 2MΩ @ 250V DC or less
• Dialectric withstand: 1 minute @ 1500V AC
• Insulation resistance: 100MΩ or more @ 500V DC

18AWG SVT power cords used in many amplifiers along with other appliances and equipment. These cords feature bare ends for hard wiring to devices internally or using a connector. The attached plug is a Nema 5-15P for North American grounded outlets. SVT cords have a thinner insulation than SJT cords. This version comes in gray to pair with vintage style amps and equipment.

High quality PCB mounted DC jack made by Cliff. This style of PCB mounted DC jack style can be found on many manufacturers’ pedals. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Three solder pins are available for tip, ring, and switch.

Genuine Cliff barrel plug for use with 5.5mm / 2.1mm barrel jacks. This plug is great for repairing power supplies and making cables. The outside housing is made of a thick durable plastic.