Power Supplies & Accessories

The Dunlop 18V power supply for Dunlop effects will save you some money on batteries and get the right power to your pedal! Features Include:

• 18 volts of regulated DC current
• 2.1 mm x 5.5 mm plug with negative center

Compatible Dunlop pedals include:

• Older Crybaby Multi-Wah
• SW-95 Slash Wah
• M108 10-band EQ
• KFK1 10-band EQ
• M117R Flanger
• EVH 117 Flanger
• DD11 Dime Distortion
• M134 Chorus
• M181 Bass Blowtorch

Plus many other pedals requiring an 18vdc power supply!

Single 9 volt battery box. See P-ECB-9V1B for single battery box with removable adapter. See P-ECB-9V2 for double battery box.

Single 9 volt battery box. See P-ECB-9V1A for single battery box without removable adapter. See P-ECB-9V2 for double battery box.

Dual 9 volt battery box. Two 9V battery compartments, each compartment having its own red and black wires for battery positive and negative connections (4 wires total) allowing for series, parallel or separate connections of two 9V batteries. Four wood screws included. Directions: 1. Refer to the Drawing B and make a hole on guitar body. 57.5 mm (2.26") x 49.5 mm (1.95"), R6 (6 mm = 0.24") 2. Put the box in guitar body and fix it by screws.

Mount these rubber grommets to the base of reverb tanks to help alleviate feedback and other vibration issues. The thick rubber ring helps with isolating the tank from the surface that it is mounted to or resting upon. These rubber grommets fit typical reverb tanks.

• Mounting Hole Diameter = 3/8"
• Outer Diameter = 1/2".

Listed diameter is inside diameter. Sold in packs of 5.

• 3/8" diameter designed for chassis hole with diameter 1/2"
• 1/8" diameter designed for chassis hole with diameter 1/4"
• 3/16" diameter designed for chassis hole with diameter 5/16"
• 1/4", small cutout diameter designed for chassis hole with diameter 3/8"
• 1/4" diameter designed for chassis hole with diameter 7/16"
• 5/16" diameter designed for chassis hole with diameter 7/16"

Large rubber grommet for mounting footswitches on FZ-1 and FZ-1A style builds. Requires a 0.812” (20.6mm) mounting hole. This grommet’s 0.5” (12.7mm) inner diameter fits most common footswitches. These are great for replacing originals, replica builds of these Maestro pedals or for general sound damping on footswitches.

Strain relief for wiring - for use in 1/4 diameter hole.

Nylon strain relief for two conductor SPT-1 wire (.11" x .21”). Protects the lifeline of your electric/electronic products by absorbing the forces of pull, push, and twist that may be exerted on flexible power cords. Securely anchors, insulates, and protects cable at panel entry points. Fits 0.375” x 0.345” mounting holes with 0.62” panel thickness.

Nylon strain relief for two or three conductor round wires ranging from 0.25” to 0.30” in diameter. Protects the lifeline of your electric/electronic products by absorbing the forces of pull, push, and twist that may be exerted on flexible power cords. Securely anchors, insulates, and protects cable at panel entry points. Fits 0.5” x 0.45” mounting holes with 0.62” panel thickness.
This is a direct fit for many vintage Fender amps with 2-prong cables, allowing for conversion to 3-prong SVT cables (such as S-W142) with the appropriate outer diameter.

16/3 SJT, 5/16" cord diameter. These one piece Strain Relief Bushings securely anchor, absorb, and protect cables and wires from push/pull and twist forces, while insulating them from irregular or sharp panel edges. They are easily and quickly installed with special installation pliers or other hand or production tools. Black H.S. Nylon, and the temperature index is 105° Centigrade.

For 35/64" x 5/8" chassis hole, 11/32" cord diameter. Fits most Fender® amps.

• Protects the lifeline of your electric/ electronic products by absorbing the forces of pull, push, and twist that may be exerted on the flexible power cord.
• Securely anchors, insulates, and protects cables at panel entry points

1/16” (.062 in.) panel thickness version of the Fender® style strain relief for 35/64" x ⅝” chassis holes and 11/32” cord diameter. Fits many Fender® amps with 1/16” thick chassis.

• Protects the lifeline of your electric/ electronic products by absorbing the forces of pull, push, and twist that may be exerted on the flexible power cord.
• Securely anchors, insulates, and protects cables at panel entry points

Marshall PC Board for TSL 100 / 122. Rev 20.

Replacement board for Marshall JCM 2000 DSL 100 amplifiers which frequently have issues with original boards. This replacement can bring your amp back to life!

Nylon cable clamps perfect for securing cables to cabinet walls. These clamps feature a .203 in. mounting hole. The ⅜ in. diameter cable clamp is commonly used on Fender® amplifiers for securing the power cord. The ¼ in. diameter cable clamp is commonly used on Fender® amplifiers for securing the RCA reverb tank cables. The 5/16 in. version works well with the S-W125X and S-W132X bare end power cables.

Black nylon cable clamps perfect for securing cables to cabinet walls. These clamps feature a .203 in. mounting hole. The ⅜ in. diameter cable clamp is commonly used on Fender® amplifiers for securing the power cord. The ¼ in. diameter cable clamp is commonly used on Fender® amplifiers for securing the RCA reverb tank cables. The 5/16 in. version works well with the S-W125X and S-W132X bare end power cables. See P-HCABLECLAMP-X for white nylon versions of these clamps.

Self adhesive metal cable clips. They easily attach to most surfaces using a strong foam adhesive. These cable clips are a great way to tidy up project wiring and securing components.

Durable heavy duty nylon cable ties. These zip ties are a great way to tidy up project wiring and securing components. Features

• Approved for outdoor use.
• UL Listed 6.6 nylon.
• Locks tightly - Won’t stretch or slide.
• Temperature range from 40° to 180°F.
• 8 inch length
• 40 lb tensile strength

Durable nylon cable ties. These zip ties are a great way to tidy up project wiring and securing components. Features

• Approved for outdoor use.
• UL Listed 6.6 nylon.
• Locks tightly - Won’t stretch or slide.
• Temperature range from 40° to 180°F.

High quality right angled 10-pin headers. Right angled headers are perfect for compact eurorack builds. The durable glass filled polyester shroud makes soldering these shrouded headers a simple task.

Metal finger-protecting guard for P-HFAN.

The LoBat™ low battery indicator circuit is designed for use in electric guitars and basses with active pickups and electronics that use 9 volt batteries. Lights when battery voltage is below 7.7V. This early warning notifies the player it's time for a new battery days before tone begins to suffer!

Nylon cable tie mounts with adhesive backing. These mounts easily attach to most surfaces using a strong foam adhesive. Zip ties can be fed through the openings on the mount to secure wires to an enclosure, board, or any other convenient location.