Power Supplies & Accessories
Cable - Power All, Red Right Angle Reverse Polarity Jumper
Included in the PA-9ECB Basic Kit, PA-9ECD Deluxe Kit, and also available separately, the Cable-Red/R allows the user to power effect units that have reverse polarity barrel connectors (tip positive/barrel negative). The Cable-Red/R features a tip positive, male barrel connector that is spring-loaded to prevent disconnection. The Cable-Red/R can be hooked to any plug on any of the Power-All daisy chains, or directly to the Power-All.
$3.25
Fuse Holder - 3AG-Type, Low Profile, Slotted, Spade Lug
Panel mount 3AG fuse holder with spade lug connectors. This fuse holder features a low profile slotted cap and reduced overall height. It is a similar style to fuse holders used on many vintage Marshall amps. Mounting nut and rubber washer included.
$3.25
Battery - 9V, Carbon Zinc, GP, Greencell, Extra Heavy Duty
Extra heavy duty carbon zinc batteries from GP. The GP Greencell 9V is a favorite for fuzz pedals and is the stock battery for many boutique builders such as D*A*M and others. Additionally, these batteries are a great choice for any low current battery powered pedal or other devices.
$3.25
Cable - Power All, Blue Right Angle Phone Plug Extension Jumper
Included in the PA-9ECD Deluxe Kit and also sold separately, the Cable-Blue/R features a right-angle jack that allows users to power effect units that use a ⅛" (3.5 MM) phone plug connector with tip-positive polarity. The Cable-Blue/R can be connected to any male jack on the Cable-5 Daisy Chain, or directly to the ECO-Dapter® itself.
$3.25
Fuse Block - for 3AB and 3AG fuses, low profile
Open frame fuse holder with patented self-aligning, snap-in terminal clips. A low profile fuse block featuring individual barriers which reinforce the fuse clips while providing greater protection against clip damage and electrical shock. The uniqu design permits self-alignment of clips to fuse cap. This, plus a one-piece clip / terminal assures low contact resistance. Higher current ratings have been attained using spring brass clips.
$3.10
Cord - Replacement Brown, Polarized Plug
Brown SPT-1 power cable
- polarized
- tinned leads
- 6 foot length
- 18 AWG
$2.95
Cable - Power All, Grey Battery Snap Jumper
Included in the PA-9ECB Basic Kit and also sold separately, the Cable-Grey allows the user to power vintage and boutique effect units that run off 9-volt batteries but do not have an external AC power jack. The Cable-Grey hooks directly to the unit's Battery Snap and can be connected to any of the Power-All daisy chains, or directly to the Power-All.
$2.95
Fuse Holder - for Fender®, 3AG-Type
High quality Fender® Style fuse holder replacement for guitar amplifiers.
- Fits ½" chassis hole diameter
- Mounted by Nut
$2.75
Plug - AC, Flat, Brown, vintage style two prong
A new two-prong plug, acceptable as a retro or vintage substitute. The plug easily accepts our twisted 18 and 16 gauge wires (two-conductor only). Wire Opening Diameter: 11.2 mm x 8.4 mm, 7/16" x 5/16" UL Rating: 15A-125V Made in Mexico
$2.75
Insulation Cover - Fuse Holder, 15.5 x 36.8mm, PVC
High quality insulation cover for panel mount fuse holders. The cover is made of a thick durable PVC and fits many fuse holders. The wire sleeve can securely fit over any standard wire gauge used with fuse holders providing a fully insulated fuse connection.
Features
Fits S-H205
Features
- Provides insulation against shock on rear of fuse holder
- PVC
- UL94V-0 rated flame retardant material
Fits S-H205
$2.65
Fuse Holder - 3AG-Type, High Quality
High quality fuse holder used with 3AG type fuse. Fits in a 1/2" diameter chassis hole. Frame and cap material: phenolic Terminal material: Nickel-plated brass Mounted by nut
$2.55
Insulation Cover - Power Inlet, IEC C14, PVC
High quality insulation cover for IEC C14 AC Power inlets. The cover is made of a thick durable PVC and fits most standard C14 type power inlets. The wire sleeve can be cut to securely fit over any standard wire gauge providing a fully insulated AC inlet.
$2.45
Cord - Replacement Black, Non-Polarized
Black SPT-1 power cable
- non-polarized
- tinned leads
- 6 foot length
- 18 AWG.
$2.44
Receptacle - IEC C14, Snap-in Panel Mount
High quality snap-in IEC C14 power entry connector. The connector is easy to install and is rated for 250VAC at 15A. The quick disconnect terminals can also be directly soldered to. Features:
- High quality thermoplastic housing
- Copper alloy terminals (4.8mm width)
- Quick installation
- Fits 0.8mm to 2mm thick panels
$2.29
Fuse - Fast-Blow, 250V, 3AG, 0.25" x 1.25"
Protect your expensive investment or hobby with inexpensive fuses.
Starting at $2.25
package of 5
Receptacle - IEC C14, for power cord, 3 prong
Plastic IEC C14 connector for power entry. This power receptacle mounts with two screw holes which are counterunk for a clean look when using countersunk screws. This is a 3 prong connector for power cables with ground connections. Internal connections can be soldered into place or used with quick disconnects. See Specifications, Files, and Documents for a datasheet with dimensions and panel cut out sizing.
$2.15
Power Jack - Lumberg, DC Panel Mount, Snap-in, 5.5mm External, 2.1mm Internal
Snap-in Lumberg panel mount barrel jack with solder lugs. This high quality jack is a similar size to the Lumberg low profile jack but easily snaps into place with no need to thread a nut inside the chassis. For use with barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter.
$2.15
Cable Cap - Power All, Insulator Caps for Barrel Connectors
Designed to fit over unused male barrel connectors on a daisy chain or power supply, Cable-Caps protect against short circuits that can occur when a live lead touches a metal surface. Sold in sets of three. Fits over standard 5.5 mm diameter barrel plug connectors.
$1.95
package of 3
Receptacle - AC with Fuse Holder, mates with S-W123 & S-W124
I.E.C. Power Cord Receptacle. Mates with power cords S-W123 and S-W124. Rated for 6A, 250V. UL listed. Compatible with GMA fuses
$1.85
Power Jack - Cliff, DC Panel Mount, Low Profile, 5.5mm External, 2.1mm Internal
High quality PCB mounted DC jack made by Cliff. This style of PCB mounted DC jack style can be found on many manufacturers’ pedals. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Three solder pins are available for tip, ring, and switch.
Colors Available:
Starting at $1.79
Grommet - Rubber, for chassis holes
Listed diameter is inside diameter. Sold in packs of 5.
- 3/8" diameter designed for chassis hole with diameter 1/2"
- 1/8" diameter designed for chassis hole with diameter 1/4"
- 3/16" diameter designed for chassis hole with diameter 5/16"
- 1/4", small cutout diameter designed for chassis hole with diameter 3/8"
- 1/4" diameter designed for chassis hole with diameter 7/16"
- 5/16" diameter designed for chassis hole with diameter 7/16"
Starting at $1.75
package of 5
PCB - Charge Pump, -9V from +9V, 3PDT Switch Mount
3PDT switch mounted charge pump PCB for positive ground effects. This small PCB simplifies the wiring of 3PDT foot switches in guitar pedals while also offering -9V when used with a standard +9V power supply. This is a great option for positive ground effects such as vintage fuzz pedals. The circuit of this PCB also features a protection diode and an LED indicator for when the effect is engaged.
This board is compatible with the MAX1044, TC1044S, TC7660S, and LT1054 charge pump ICs.
This board is compatible with the MAX1044, TC1044S, TC7660S, and LT1054 charge pump ICs.
$1.60
PCB - Charge Pump, -9V from +9V, Screw Mount
Screw mounted charge pump PCB for positive ground effects. This small PCB provides -9V when used with a standard +9V power supply. This is a great option for positive ground effects such as vintage fuzz pedals. The PCB has a low profile design and is a simple addition to any build using a standoff to mount the board. This board is compatible with the MAX1044, TC1044S, TC7660S, and LT1054 charge pump ICs.
$1.60
Power Jack - Lumberg, DC Panel Mount, 5.5mm External, 2.1mm Internal
Lumberg panel mount barrel jack with solder lugs.This DC jack features a normally closed switch on the ring (sleeve) connection. For use with barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Mounting nut included.
$1.59