Power Supplies & Accessories

Power Supply - Power-All® ECO-Dapter®, Cable Kits, for Effects Pedals
Power-All® ECO-Dapter® is a center negative 9VDC power supply for effects pedals that can supply up to 2000mA of power making it a great choice for pedals boards and power hungry effects. Power-All® kits include a variety of useful cables for powering multiple pedals to the ECO-Dapter® 9V supply.
Starting at $30.95
Battery Clip - Premium, 9 Volt, Rigid Frame, T-Style, Shielded Eyelets
Premium 9V battery clip made of a rigid plastic frame with an insulating wall enclosing the battery terminals. This high quality battery snap features nickel-plated brass contacts. The six inch leads are 26 AWG stranded wire, prestripped and tinned for an easy installation.
$1.15
Wire - 18 Gauge, 2 conductor, braided Power Cord
Brown 2 conductor 18 gauge, stranded power cord, similar to woven cloth covered cords in early AC radios. 105°C temperature rating, 600V.
Starting at $26.75
Dust Cap - For DC Power Jack, Low Profile Size
Dust cover for smaller low profile DC power jacks. This cover is simple to install and can help protect the power jack on effects pedals and other electronics using this style of DC jack. Jack sold separately.
$0.30
Fuse Holder - 3AG-Type, Tweed Style, Right Angle Spade Lug
Panel mount 3AG fuse holder with spade lug connectors. This fuse holder matches the style of vintage tweed amps and is a great replacement for original amps or new builds. Mounting nut and rubber washer included.
Note: The spade lugs have a detent rather than a hole.
$5.95
Power Board Kit - Marshall, For AVT Series
Marshall replacement power board.
Works in the following models:
  • AVT50
  • AVT100
  • AVT150H
  • AVT150
  • AVT275
  • AVT275X
$66.60
Battery Box - Gotoh, Dual, for 9 volt batteries
Dual 9 volt battery box. Two 9V battery compartments, each compartment having its own red and black wires for battery positive and negative connections (4 wires total) allowing for series, parallel or separate connections of two 9V batteries. Four wood screws included. Directions: 1. Refer to the Drawing B and make a hole on guitar body. 57.5 mm (2.26") x 49.5 mm (1.95"), R6 (6 mm = 0.24") 2. Put the box in guitar body and fix it by screws.
$19.00
Cable - Power All, Red Right Angle Reverse Polarity Jumper
Included in the PA-9ECB Basic Kit, PA-9ECD Deluxe Kit, and also available separately, the Cable-Red/R allows the user to power effect units that have reverse polarity barrel connectors (tip positive/barrel negative). The Cable-Red/R features a tip positive, male barrel connector that is spring-loaded to prevent disconnection. The Cable-Red/R can be hooked to any plug on any of the Power-All daisy chains, or directly to the Power-All.
$3.25
Receptacle - IEC C14, Panel Mount, Fuse Holder, 10A, 250VAC
Plastic IEC C14 connector for power entry. This power receptacle mounts with two screw holes which are counterunk for a clean look when using countersunk screws. This is a 3 prong connector for power cables with ground connections. Internal connections can be soldered into place or used with quick disconnects. This receptacle features a built-in fuse holder for 5mm x 20mm fuses. See Specifications, Files, and Documents for a datasheet with dimensions and panel cut out sizing.
$3.50
Cable - Power All, Green Right Angle Line-6 Extension Jumper
Included in the PA-9ECB Basic Kit, PA-9ECD Deluxe Kit, and also available separately, the Cable-Green Right Angle jumper allows the user to power Line-6 Stomp-Box modelers and other digital effect units from the ECO-Dapter®. The Cable-Green features a reverse-polarity (tip positive), right-angle male barrel connector with a larger, 2.5 mm internal diameter and spring-loaded clips. The Cable-Green/R can be used with Line-6 Modelers, Electro-Harmonix units, and other pedals requiring a larger internal diameter plug. the Cable-Green/R can be connected to the male plugs on any Power-All Daisy Chain, or directly to the ECO-Dapter® itself.
$3.25
PCB - Charge Pump, -9V from +9V, Screw Mount
Screw mounted charge pump PCB for positive ground effects. This small PCB provides -9V when used with a standard +9V power supply. This is a great option for positive ground effects such as vintage fuzz pedals. The PCB has a low profile design and is a simple addition to any build using a standoff to mount the board. This board is compatible with the MAX1044, TC1044S, TC7660S, and LT1054 charge pump ICs.
$1.55
Insulation Cover - Power Inlet, IEC C14, PVC
High quality insulation cover for IEC C14 AC Power inlets. The cover is made of a thick durable PVC and fits most standard C14 type power inlets. The wire sleeve can be cut to securely fit over any standard wire gauge providing a fully insulated AC inlet.
$2.45
Battery Box - Gotoh, single, 9 volt, with removable adapter
Single 9 volt battery box. See P-ECB-9V1A for single battery box without removable adapter. See P-ECB-9V2 for double battery box.
$13.95
Battery Holder - AA, Chassis Mount, Wired, Single
Prewired AA battery holder. This plastic battery holder fits a single AA battery and is a great option for vintage fuzz pedals that run on 1.5V, such as the Maestro FZ-1A.
$1.10
Fuse Holder - for Marshall, GMA or GMD Type, PCB Mount
Though-hole PCB mount fuse holder used on many Marshall amps such as the 900 series and some 2000 series amps. The fuse cap is sold separately as S-H204. Fits GMA and GMD 5×20mm fuses.
$3.50
Cable - Power All, 11 Lead Right Angle Daisy Chain
Designed for larger pedalboards, the Power-All Cable-11/R Daisy Chain features ELEVEN right-angle male barrel plugs with spring loaded jacks for extra secure connections – no more losing power mid-solo! 28-gauge cable with oil-resistant sheath and 10-inch cable length between plugs allows connection of larger and odd-sized pedals.
$16.25
Fuse Holder - 3AG-Type, Tweed Style, Solder Lug
Panel mount 3AG fuse holder with solder lug connectors. This fuse holder matches the style of vintage tweed amps and is a great replacement for original amps or new builds. Mounting nut and rubber washer included.
$3.55
PCB - Charge Pump, -9V from +9V, 3PDT Switch Mount
3PDT switch mounted charge pump PCB for positive ground effects. This small PCB simplifies the wiring of 3PDT foot switches in guitar pedals while also offering -9V when used with a standard +9V power supply. This is a great option for positive ground effects such as vintage fuzz pedals. The circuit of this PCB also features a protection diode and an LED indicator for when the effect is engaged.
This board is compatible with the MAX1044, TC1044S, TC7660S, and LT1054 charge pump ICs.
$1.55
Fuse Set - Fast and Slow Blow, 0.25" x 1.25", 8 types, 20 each
Package of 160
Fuse kit, fast and slow blow. Contains the following fuses:
  • 20x Slo-Blo, 2 Amp F-Z3AG-S2
  • 20x Slo-Blo, 3 Amp F-Z3AG-S3
  • 20x Slo-Blo, 1 Amp F-Z3AG-S1
  • 20x Slo-Blo, 4 Amp F-Z3AG-S4
  • 20x Slo-Blo, 5 Amp F-Z3AG-S5
  • 20x Fast-Blo, 2.5 Amp F-Z3AG-F2D5
  • 20x Fast-Blo, 1 Amp F-Z3AG-F1
  • 20x Fast-Blo, 3 Amp F-Z3AG-F3
$88.95
Fan Guard - Metal Grill, Finger Guard
Metal finger-protecting guard for P-HFAN.
$3.50
Power Supply - Dunlop, 18V A/C Adapter
The Dunlop 18V power supply for Dunlop effects will save you some money on batteries and get the right power to your pedal! Features Include:
  • 18 volts of regulated DC current
  • 2.1 mm x 5.5 mm plug with negative center

Compatible Dunlop pedals include:
  • Older Crybaby Multi-Wah
  • SW-95 Slash Wah
  • M108 10-band EQ
  • KFK1 10-band EQ
  • M117R Flanger
  • EVH 117 Flanger
  • DD11 Dime Distortion
  • M134 Chorus
  • M181 Bass Blowtorch

Plus many other pedals requiring an 18vdc power supply!
$16.25
Power Supply - Dunlop, 9V, 200mA, Barrel, Center Negative

Dunlop ECB003 US wallwart power supply. Barrel connector.

  • Voltage: 9VDC
  • Current: 200mA
  • Tip Negative; Sleeve positive
$12.65
Fan - 115V, AC ~\frac{50}{60}~ Hz, 1 Phase, low noise
Super low noise 115V-AC. Dimensions are 4 11/16" (height) x 4 11/16" (width) x 1 ½" (depth). The distance between mounting centers is 4 1/8" x 4 1/8".
$29.95
Barrel Plug - Switchcraft, Cable Mount, Heavy Duty, 5.5mm External, 2.1mm Internal
Heavy duty mil-spec barrel plug from Switchcraft. The S10 is a high current, non-sealed power jack with a similar design as the ¼” jacks from Switchcraft. The plug is rated for up to 11A of current.
$5.95