Power Supplies & Accessories

18AWG SVT power cords used in many amplifiers along with other appliances and equipment. These cords feature bare ends for hard wiring to devices internally or using a connector. The attached plug is a Nema 5-15P for North American grounded outlets. SVT cords have a thinner insulation than SJT cords. This version comes in gray to pair with vintage style amps and equipment.

Included in the PA-9ECB Basic Kit and also sold separately, the Cable-Grey allows the user to power vintage and boutique effect units that run off 9-volt batteries but do not have an external AC power jack. The Cable-Grey hooks directly to the unit's Battery Snap and can be connected to any of the Power-All daisy chains, or directly to the Power-All.

New-old-stock Soviet fuse holders. These panel mount holders fit 5x20mm GMA and GMD type fuses. A 0.625” mounting hole is required. Note: A small 0.1” notch must either be filed into the 0.625” mounting hole or filed off of the fuse to flush mount with a panel

Panel mount 3AG fuse holder with spade lug connectors. This fuse holder matches the style of vintage tweed amps and is a great replacement for original amps or new builds. Mounting nut and rubber washer included.
Note: The spade lugs have a detent rather than a hole.

Detachable 3 conductor power cord for European wall outlets. GTSA-3 (Marshall™ type) 18 AWG. 2-1/2 meters (about 8 feet) length, 1/4” outer diameter.

Premium 9V battery clip made of a rigid plastic frame with an insulating wall enclosing the battery terminals. This high quality battery snap features nickel-plated brass contacts. The six inch leads are 26 AWG stranded wire, prestripped and tinned for an easy installation.

Fuse Holder - High Quality Marshall Snap-In Style (Fits 5/8" to 11/16" Chassis Holes). Suitable for 1/4" fuses. UL and CSA approved. Electrical Specifications:

• Rated current: 10A
• Rated voltage: 250V AC
• Contact resistance: 2MΩ @ 250V DC or less
• Dialectric withstand: 1 minute @ 1500V AC
• Insulation resistance: 100MΩ or more @ 500V DC

High quality ½" panel mount DC jack with solder lugs from Cliff Electronic Components. This jack is rear mounted which makes troubleshooting and repairs simpler since the jack does not need to be desoldered if the circuit needs to be removed from the enclosure. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Three solder lugs are available for tip, ring, and switch. Mounting nut included.

The Dunlop 18V power supply for Dunlop effects will save you some money on batteries and get the right power to your pedal! Features Include:

• 18 volts of regulated DC current
• 2.1 mm x 5.5 mm plug with negative center

Compatible Dunlop pedals include:

• Older Crybaby Multi-Wah
• SW-95 Slash Wah
• M108 10-band EQ
• KFK1 10-band EQ
• M117R Flanger
• EVH 117 Flanger
• DD11 Dime Distortion
• M134 Chorus
• M181 Bass Blowtorch

Plus many other pedals requiring an 18vdc power supply!

Protect your expensive investment or hobby with inexpensive fuses. Time-delay, low breaking capacity. Rated at 250V. Package of 5

Panel mount 3AG fuse holder with spade lug connectors. This fuse holder features a low profile slotted cap and reduced overall height. It is a similar style to fuse holders used on many vintage Marshall amps. Mounting nut and rubber washer included.

Single 9 volt battery box. See P-ECB-9V1B for single battery box with removable adapter. See P-ECB-9V2 for double battery box.

Screw mounted charge pump PCB for positive ground effects. This small PCB provides -9V when used with a standard +9V power supply. This is a great option for positive ground effects such as vintage fuzz pedals. The PCB has a low profile design and is a simple addition to any build using a standoff to mount the board. This board is compatible with the MAX1044, TC1044S, TC7660S, and LT1054 charge pump ICs.

Peavey cap for fuse holder. 1 1/16" length x 3/8" diameter. Top slotted for flat head screwdriver.

Though-hole PCB mount fuse holder used on many Marshall® JCM2000 series such as the TSL100, TSL122, DSL50, and DSL100 as well as other amps. Check footprint and dimensions for compatibility. This holder fits 3AG fuses and pairs with the S-H212 cap. Cap sold separately.

Single standard snap-on 9V battery clip. Features six inch pre-stripped and pre-tinned leads for an easy connection.

KA-193 wallwart power supply. For use with PX4, PX4B and PXR4.

• Voltage: 4.5VDC
• Current: 500mA
• Tip positive; Sleeve negative

High quality chassis mount battery holder. This steel holder fits standard 9V batteries. The vertical mount and small footprint of the holder are great for narrow spaces and work well for any project. See S-H158 for horizontal-mount.

Dual 9 volt battery box. Two 9V battery compartments, each compartment having its own red and black wires for battery positive and negative connections (4 wires total) allowing for series, parallel or separate connections of two 9V batteries. Four wood screws included. Directions: 1. Refer to the Drawing B and make a hole on guitar body. 57.5 mm (2.26") x 49.5 mm (1.95"), R6 (6 mm = 0.24") 2. Put the box in guitar body and fix it by screws.

Extra heavy duty carbon zinc batteries from GP. The GP Greencell 9V is a favorite for fuzz pedals and is the stock battery for many boutique builders such as D*A*M and others. Additionally, these batteries are a great choice for any low current battery powered pedal or other devices.

High quality fuse holder used with 3AG type fuse. Fits in a 1/2" diameter chassis hole. Frame and cap material: phenolic Terminal material: Nickel-plated brass Mounted by nut

Cable for connecting 9V batteries to pedals via their DC input jack. This cable is great for using batteries with pedals that don’t have a battery compartment or for quickly switching from a power supply to a battery. This cable is 3 ¼” inches in length. The barrel plug has a 5.5mm outer diameter and 2.1mm inner diameter. Battery not included.

Fuse holder cap replacement for P-SP2-500 power receptacle.

Power-All® ECO-Dapter® is a center negative 9VDC power supply for effects pedals that can supply up to 2000mA of power making it a great choice for pedals boards and power hungry effects.