Power Supplies & Accessories

Power Jack - Cliff, DC Panel Mount, Rear Mount, 5.5mm External, 2.1mm Internal
High quality ½" panel mount DC jack with solder lugs from Cliff Electronic Components. This jack is rear mounted which makes troubleshooting and repairs simpler since the jack does not need to be desoldered if the circuit needs to be removed from the enclosure. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Three solder lugs are available for tip, ring, and switch. Mounting nut included.
$1.15
Insulation Cover - Fuse Holder, 15.5 x 36.8mm, PVC
High quality insulation cover for panel mount fuse holders. The cover is made of a thick durable PVC and fits many fuse holders. The wire sleeve can securely fit over any standard wire gauge used with fuse holders providing a fully insulated fuse connection.
Features
  • Provides insulation against shock on rear of fuse holder
  • PVC
  • UL94V-0 rated flame retardant material

Fits S-H205
$2.19
Cord - Power, 18 AWG, 3 Conductor, SVT, 6 ft, Gray
18AWG SVT power cords used in many amplifiers along with other appliances and equipment. These cords feature bare ends for hard wiring to devices internally or using a connector. The attached plug is a Nema 5-15P for North American grounded outlets. SVT cords have a thinner insulation than SJT cords. This version comes in gray to pair with vintage style amps and equipment.
$3.95
On Backorder
Cable Clamp - Nylon, .203” Mounting Hole
Nylon cable clamps perfect for securing cables to cabinet walls. These clamps feature a .203 in. mounting hole. The ⅜ in. diameter cable clamp is commonly used on Fender® amplifiers for securing the power cord. SKU Diameter P-HCABLECLAMP-38 ⅜ in. P-HCABLECLAMP-12 ½ in.
Starting at $0.25
Power Jack - Lumberg, DC Panel Mount, Low Profile, 5.5mm External, 2.1mm Internal
Low profile Lumberg panel mount barrel jack with solder lugs. This high quality jack is the perfect size for smaller builds where additional space is necessary. The Lumberg low profile DC jack is also great for builds where aesthetics are a priority. For use with barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Mounting nut included.
$1.25
Fuse Holder Cap - 3AG, Slotted, for Marshall 2000 Series
Fuse holder cap for the fuse holder found on the Marshall® JCM2000 series such as the TSL100, TSL122, DSL50, and DSL100 as well as other amps. This cap fits 3AG fuses and pairs with S-H211.
$3.95
Strain Relief - for ~\frac{35}{64}~" x ⅝" Hole, .062" Panel Thickness
1/16” (.062 in.) panel thickness version of the Fender® style strain relief for 35/64" x ⅝” chassis holes and 11/32” cord diameter. Fits many Fender® amps with 1/16” thick chassis.
  • Protects the lifeline of your electric/ electronic products by absorbing the forces of pull, push, and twist that may be exerted on the flexible power cord.
  • Securely anchors, insulates, and protects cables at panel entry points
$0.95
Strain Relief - Nylon, 0.11" x 0.21" Wire (SPT-1)
Nylon strain relief for two conductor SPT-1 wire (.11" x .21”). Protects the lifeline of your electric/electronic products by absorbing the forces of pull, push, and twist that may be exerted on flexible power cords. Securely anchors, insulates, and protects cable at panel entry points. Fits 0.375” x 0.345” mounting holes with 0.62” panel thickness.
$0.50
Strain Relief - Nylon, 0.3", 2 or 3 Conductor Wire
Nylon strain relief for two or three conductor round wires ranging from 0.25” to 0.30” in diameter. Protects the lifeline of your electric/electronic products by absorbing the forces of pull, push, and twist that may be exerted on flexible power cords. Securely anchors, insulates, and protects cable at panel entry points. Fits 0.5” x 0.45” mounting holes with 0.62” panel thickness.
This is a direct fit for many vintage Fender amps with 2-prong cables, allowing for conversion to 3-prong SVT cables (such as S-W142) with the appropriate outer diameter.
$0.80
Fuse Block - For GMA / GMD Fuses, Low Profile
Open frame fuse block for GMA or GMD 5×20mm size fuses with a low profile design that features solder terminals made of tin plated brass. A unique design feature provides self-alignment of the clips to the fuse caps. This feature, plus a one-piece clip/terminal design, assures low contact resistance.
$3.55
Fuse Holder - for Marshall, GMA or GMD Type, PCB Mount
Though-hole PCB mount fuse holder used on many Marshall amps such as the 900 series and some 2000 series amps. The fuse cap is sold separately as S-H204. Fits GMA and GMD 5×20mm fuses.
$3.50
Fuse Holder - 3AG-Type, Tweed Style, Solder Lug
Panel mount 3AG fuse holder with solder lug connectors. This fuse holder matches the style of vintage tweed amps and is a great replacement for original amps or new builds. Mounting nut and rubber washer included.
$3.55
On Backorder
Fuse Holder - Clip, GMA-Type, PCB Mount
Through-hole PCB mounted fuse holder clips found in Peavey amps and other electronics. These small clips allow for minimal space fuse mourning directly on PCB’s. Fits GMA 5×20mm fuses. A pair is required to mount a fuse. Sold individually.
$0.20
On Backorder
Insulation Cover - Power Inlet, IEC C14, PVC
High quality insulation cover for IEC C14 AC Power inlets. The cover is made of a thick durable PVC and fits most standard C14 type power inlets. The wire sleeve can be cut to securely fit over any standard wire gauge providing a fully insulated AC inlet.
$2.25
Fuse Holder - GMA or GMD Type, Low Profile, Slotted, Spade Lug
Panel mount GMA or GMD (5x20mm) fuse holder with spade lug connectors. This fuse holder features a low profile slotted cap and reduced overall height. It is a similar style to fuse holders used on many Marshall amps. Mounting nut included.
$3.95
Fuse Holder - 3AG-Type, Low Profile, Slotted, Spade Lug
Panel mount 3AG fuse holder with spade lug connectors. This fuse holder features a low profile slotted cap and reduced overall height. It is a similar style to fuse holders used on many vintage Marshall amps. Mounting nut and rubber washer included.
$3.25
Fuse Holder - 3AG-Type, Tweed Style, Right Angle Spade Lug
Panel mount 3AG fuse holder with spade lug connectors. This fuse holder matches the style of vintage tweed amps and is a great replacement for original amps or new builds. Mounting nut and rubber washer included.
Note: The spade lugs have a detent rather than a hole.
$5.95
Fuse Holder - 3AG-Type, Low Profile, Knob, Right Angle Spade Lug
Panel mount 3AG fuse holder with spade lug connectors. This fuse holder features a low profile bayonet style knob and reduced overall height. The connector at the end of the holder is right angled which reduces the internal depth as well. It is a similar style to fuse holders used on many Fender® amps. Mounting nut and rubber washer included.
$5.95
Power Jack - Lumberg, DC Panel Mount, 5.5mm External, 2.1mm Internal
Lumberg panel mount barrel jack with solder lugs.This DC jack features a normally closed switch on the ring (sleeve) connection. For use with barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Mounting nut included.
$1.15
Barrel Plug - Cliff, Cable Mount, 5.5mm External, 2.1mm Internal
Genuine Cliff barrel plug for use with 5.5mm / 2.1mm barrel jacks. This plug is great for repairing power supplies and making cables. The outside housing is made of a thick durable plastic.
$1.05
Fuse - Slow-Blow, 250V, Miniature, GMD-type 5mm x 20mm
Package of 5
Protect your expensive investment or hobby with inexpensive fuses. Time-delay, low breaking capacity. Rated at 250V. Package of 5
$3.50
Replacement Fuse Holder Cap - For P-SP2-500
Fuse holder cap replacement for P-SP2-500 power receptacle.
$1.00
On Backorder
Cord - Power, 18 AWG, 3 Conductor, Detachable, Black, IEC
Three conductor, 8 or 12 foot detachable power cord with IEC female end SVT (Marshall type), 18 awg.
Starting at $5.65
Grommet - Rubber, for chassis holes
Package of 5
Listed diameter is inside diameter. Sold in packs of 5.
  • 3/8" diameter designed for chassis hole with diameter 1/2"
  • 1/8" diameter designed for chassis hole with diameter 1/4"
  • 3/16" diameter designed for chassis hole with diameter 5/16"
  • 1/4", small cutout diameter designed for chassis hole with diameter 3/8"
  • 1/4" diameter designed for chassis hole with diameter 7/16"
  • 5/16" diameter designed for chassis hole with diameter 7/16"
Starting at $0.95