Power Supplies & Accessories

High quality fuse holder used with 3AG type fuse. Fits in a 1/2" diameter chassis hole. Frame and cap material: phenolic Terminal material: Nickel-plated brass Mounted by nut
$2.55

Three conductor, 8 or 12 foot detachable power cord with IEC female end SVT (Marshall type), 18 awg.
Starting at $6.25

The 3AG Slo-Blo fuse solves a broad range of application requirements while offering reliable performance and costeffective circuit protection. Fits fuse block S-H259 and fuse holder S-H201.
$3.25
package of 5

High quality Fender® Style fuse holder replacement for guitar amplifiers.
- Fits ½" chassis hole diameter
- Mounted by Nut
$2.75

Colors Available:
$0.99

18AWG SJT power cords used in many amplifiers along with other appliances and equipment. These cords feature bare ends for hard wiring to devices internally or using a connector. The attached plug is a Nema 5-15P for North American grounded outlets. These cords have a maximum voltage rating of 300V.
Starting at $5.55

Power Cord / cable - (3 conductor) Bare End, 16 AWG
Starting at $6.99

Plastic IEC C14 connector for power entry. This power receptacle mounts with two screw holes which are counterunk for a clean look when using countersunk screws. This is a 3 prong connector for power cables with ground connections. Internal connections can be soldered into place or used with quick disconnects. See Specifications, Files, and Documents for a datasheet with dimensions and panel cut out sizing.
$2.15

Low profile Lumberg panel mount barrel jack with solder lugs. This high quality jack is the perfect size for smaller builds where additional space is necessary. The Lumberg low profile DC jack is also great for builds where aesthetics are a priority. For use with barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Mounting nut included.
Note: As of 2023, Lumberg has updated the design of these jacks.
Note: As of 2023, Lumberg has updated the design of these jacks.
$1.55

Nylon cable clamps perfect for securing cables to cabinet walls. These clamps feature a .203 in. mounting hole. The ⅜ in. diameter cable clamp is commonly used on Fender® amplifiers for securing the power cord. The ¼ in. diameter cable clamp is commonly used on Fender® amplifiers for securing the RCA reverb tank cables. The 5/16 in. version works well with the S-W125X and S-W132X bare end power cables.
Starting at $0.26

Lumberg panel mount barrel jack with solder lugs.This DC jack features a normally closed switch on the ring (sleeve) connection. For use with barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Mounting nut included.
$1.35

For 35/64" x 5/8" chassis hole, 11/32" cord diameter. Fits most Fender® amps.
- Protects the lifeline of your electric/ electronic products by absorbing the forces of pull, push, and twist that may be exerted on the flexible power cord.
- Securely anchors, insulates, and protects cables at panel entry points
$0.69

Listed diameter is inside diameter. Sold in packs of 5.
- 3/8" diameter designed for chassis hole with diameter 1/2"
- 1/8" diameter designed for chassis hole with diameter 1/4"
- 3/16" diameter designed for chassis hole with diameter 5/16"
- 1/4", small cutout diameter designed for chassis hole with diameter 3/8"
- 1/4" diameter designed for chassis hole with diameter 7/16"
- 5/16" diameter designed for chassis hole with diameter 7/16"
Starting at $1.75
package of 5

Low profile DC jack with solder lugs. This jack is the perfect size for smaller builds where additional space is necessary. The low profile DC jack is also great for builds where aesthetics are a priority. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Features two solder lugs for tip and ring.
$0.70

High quality ½" panel mount DC jack with solder lugs from Cliff Electronic Components. This jack is rear mounted which makes troubleshooting and repairs simpler since the jack does not need to be desoldered if the circuit needs to be removed from the enclosure. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Three solder lugs are available for tip, ring, and switch. Mounting nut included.
$1.35

Protect your expensive investment or hobby with inexpensive fuses. Time-delay, low breaking capacity. Rated at 250V. Package of 5
$3.95
package of 5

Self adhesive metal cable clips. They easily attach to most surfaces using a strong foam adhesive. These cable clips are a great way to tidy up project wiring and securing components.
Starting at $1.25
package of 5

Single standard snap-on 9V battery clip. Features six inch pre-stripped and pre-tinned leads for an easy connection.
$0.50

Protect your expensive investment or hobby with inexpensive fuses.
Starting at $2.25
package of 5

Nylon strain relief for two or three conductor round wires ranging from 0.25” to 0.30” in diameter. Protects the lifeline of your electric/electronic products by absorbing the forces of pull, push, and twist that may be exerted on flexible power cords. Securely anchors, insulates, and protects cable at panel entry points. Fits 0.5” x 0.45” mounting holes with 0.62” panel thickness.
This is a direct fit for many vintage Fender amps with 2-prong cables, allowing for conversion to 3-prong SVT cables (such as S-W142) with the appropriate outer diameter.
This is a direct fit for many vintage Fender amps with 2-prong cables, allowing for conversion to 3-prong SVT cables (such as S-W142) with the appropriate outer diameter.
$0.85

Mount these rubber grommets to the base of reverb tanks to help alleviate feedback and other vibration issues. The thick rubber ring helps with isolating the tank from the surface that it is mounted to or resting upon. These rubber grommets fit typical reverb tanks.
- Mounting Hole Diameter = 3/8"
- Outer Diameter = 1/2".
$1.30
package of 4

Premium 9V battery clip with a rigid plastic frame and I-style wire orientation. This high quality battery snap features nickel-plated phosphor bronze contacts. The six inch leads are 26 AWG stranded wire, prestripped and tinned for an easy installation.
$1.20

High quality snap-in IEC C14 power entry connector. The connector is easy to install and is rated for 250VAC at 15A. The quick disconnect terminals can also be directly soldered to. Features:
- High quality thermoplastic housing
- Copper alloy terminals (4.8mm width)
- Quick installation
- Fits 0.8mm to 2mm thick panels
$2.29

1/16” (.062 in.) panel thickness version of the Fender® style strain relief for 35/64" x ⅝” chassis holes and 11/32” cord diameter. Fits many Fender® amps with 1/16” thick chassis.
- Protects the lifeline of your electric/ electronic products by absorbing the forces of pull, push, and twist that may be exerted on the flexible power cord.
- Securely anchors, insulates, and protects cables at panel entry points
$0.95