You are here


Filter these results
Sort By:
products per page
View Mode: List View · Grid View
P-QMJ15016Transistor - MJ15016, PNP, Complementary High-Power
Transistor MJ15016, TO-3 Case, PNP

PowerBase complementary transistors designed for high power audio, stepping motor and other linear applications. These devices can also be used in power switching circuits such as relay or solenoid drivers, dc–to–dc converters, inverters, or for inductive loads requiring higher safe operating areas.

Safe Operating Area - Rated to 60V
Click to read more
P-QLF353Op-Amp - LF353, Dual, Wide-Bandwidth, JFET Input, 8-Pin DIP

Dual wide-bandwidth LF353 opamps in an 8-pin DIP package. The LF353 offers a high input impedance and 3MHz bandwidth.

This LF353 device is a low-cost, high-speed, JFET input operational amplifier with very low input offset voltage. It requires low supply current yet maintains a large gain-bandwidth product and a fast slew rate. In addition, the matched high-voltage JFET input provides very low input bias and offset currents.

Click to read more
P-Q1N4937Diode - Fast Recovery, 1A, 600V, 1N4937

A semiconductor device that, above a certain reverse voltage(the zener value) has a sudden rise in current. If forward biased, the diode is an ordinary rectifier. When reverse biased, it exhibits a sharp break in its current-voltage graph. Voltage across the diode remains essentially constant for any further increase of reverse current.

Click to read more
P-QLM386N1Audio Power Amplifier - LM386N-1, Low Voltage

LM386 Low Voltage Audio Power Amplifier The LM386 is a mono low voltage amplifier that can be used in a variety of applications. It can drive loads from 4 Ω to 32 Ω. The gain is internally set to 20 but it can be modified from 20 to 200 by placing a resistor and capacitor between pins 1 and 8. As this is an Op Amp it can be used in different configurations to fit in several applications. The internal gain setting resistor allows the LM386 to be used in a very low part count system. In addition a series resistor can be placed between pins 1 and 5 to modify the gain and frequency response for specific applications. These are found in many small audio amplifiers and even tiny pedal sized guitar amplifiers! There are tons of possibilities for this little Op Amp.

Click to read more
P-Q2N5400Transistor - Peavey, 2N5400, PNP Amp, 120V, 20MA, TO-92

2N5400 (761), PNP general purpose amp, 120V, 10mA, TO-92 case.

Click to read more
P-QBA4560Op-Amp - BA4560, Dual, General Purpose, 8-Pin DIP

The BA4560, is a dual operational amplifiers which achieves approximately twice the high output current of the BA4558, as well as featuring a higher slew rate of 4V / µs, a gain band width of 10MHz, and an improved frequency characteristic. 8-pin DIP package.

Click to read more
P-QHFA08Diode - Hexfred, ultrafast soft recovery, 8A, 600V

High performance, ultrafast diodes. Improve efficiency, reduce noise, allow higher frequency operation.

Click to read more
P-QM5201Op-Amp - M5201, Dual, With Switch, 8-Pin DIP

The NJM2120 is a dual operational amplifier of 2-INPUT and 1-OUTPUT with analog switch. The NJM2120 can be used as analog switch under the condition of GV=0dB, as Switch + Amp in order that each gain (A or B) can be adjusted independently. Each amplifier of the NJM2120 has the same electrical characteristics as the NJM4558. The NJM2120 is suitable for audio, video, electrical musical instrument, etc.

Click to read more
P-QPC1188HIntegrated Circuit - Fender®, Power Amp PC1188H

PC 1188H Power Amp - Fender The PC1188H is a monolithic integrated circuit and a power amplifier designed for Hi-Fi audio sets. The PC1188H can provide 20W (typical) to 8 ohms at 1% T.H.D. and +/- 22V supply voltage. Features:

  • High output power
  • Low distortion
  • Wide frequency bandwidth
  • A muting function which eliminates pop on noise and the thermal and the over current protection circuit

Click to read more
P-QSBS14Diode Thyristor - Peavey, SBS 14 Bidirectional, 8V, TO-92 Case

Designed for full-wave triggering in Triac phase control circuits, half-wave SCR triggering application and as voltage level detectors. Used in most Peavey linear power amplifier designs through 2000 including CS/M/DECA series power amps, IPA300, and all models using 402/602/304S/204S power modules.

  • Low Switching Voltage — 8 Volts Typical
  • Uniform Characteristics in Each Direction
  • Low On-State Voltage — 1.7 Volts Maximum
  • Low Off-State Current — 0.1 mA Maximum

Click to read more
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Semiconductors