# Semiconductors

Op-Amp - Orange, Dual Discrete, Low-Noise, 8-Pin DIP
The Dual Discrete op-amp is specially designed for audio and is among the most musical sounding dual discrete op-amps out there. It is available in DIP 8 format and can be used in any CD player, DAC, or preamplifier that currently runs DIP 8 based IC dual op-amp types. The overall soundstage and transient detail will be greatly improved when used in pretty much all audio equipment that it can physically be fitted to. It has a very low noise Jfet front end so it can run with input impedances above 1M Ohms if needed. It can replace the following, provided the equipment it’s being used in has 22mm of height clearance and 5mm side clearance (per side).
• OPA2604
• OPA2134
• TL072
• NE5532
• LM4562
• OP275
• OP285

Please check that the PSU can supply the extra current needed, especially if replacing more than one existing IC op-amp with our op-amp as with all discrete types, they do draw more current.
$46.75 Save 15% Originally:$55.00
Integrated Circuit - DAB2130, VCO, Sound Semiconductor
The Sound Semiconductor DAB2130 is a pre-soldered DIP converter for the SSI2130. This board features the SSI2130 and two decoupling caps for the V+ and V- inputs. The pinout is labelled on the board and matches the QFN pinout. This adapter features a 32 pin DIP base with a .600 in. width. The pins are standard male headers so 2.54mm female headers are recommended for socketing the board. For the standard QFN version, please see P-Q-SSI2130. The first new VCO IC in decades, and worth the wait! The FatKeys™ SSI2130 Voltage Controlled Oscillator provides beautiful triangle, sawtooth, pulse, and square waveforms with unprecedented temperature stability; and adds an on-chip mixer, low distortion sine wave generator, through-zero FM/PM capability and more in an ultra-compact PCB footprint. The SSI2130 is a new-generation voltage controlled oscillator subsystem for high-performance electronic musical instruments.
$19.95 Integrated Circuit - DAB2140, Multi-Mode VCF, Sound Semiconductor The Sound Semiconductor DAB2140 is a pre-soldered DIP converter for the SSI2140. This board features the SSI2140 and two decoupling caps for the V+ and V- inputs. The pinout is labelled on the board and matches the SSOP pinout. This adapter features a 20 pin DIP base with a .600 in. width. The pins are standard male headers so 2.54mm female headers are recommended for socketing the board. For the SSOP version, please see P-Q-SSI2140. A refresh of a classic design, the FatKeys™ SSI2140 preverses mojo of the beloved SSM2040 and adds temperature compensation of gm cells and the exponential control port. A "Q VCA" is provided to allow easy resonance control as well as various options for Q compensation.$19.95
Integrated Circuit - Spin FV-1, DSP, Multi-Effect / Reverb
The Spin Semiconductor FV-1 is a complete reverb solution in a single IC. With integrated stereo ADC and DACs, the FV-1 can be treated like any other analog component in your product's signal path. The FV-1 can access a total of 16 programs, 8 are built into the internal ROM and the designer may elect to connect a serial EEPROM with 8 additional programs. By using an external EEPROM, the designer can distinguish his product from others by creating a custom program set without the need for a microprocessor in the system. With 3 potentiometer inputs, programs may have real time variable parameters such as decay time in a reverb, rate and depth in a chorus or frequency in a filter. These inputs are available as coefficients to your program and may be used independently of each other. The rich instruction set allows users to program effects of all kinds. With instructions like LOG and EXP, users can easily program audio expansion and compression routines.
$17.50 Integrated Circuit - Marshall, TDA7293 amplifier 120V - 100W DMOS audio amplifier with mute/standby. The TDA7293 is a monolithic integrated circuit in Multiwatt15 package, intended for use as audio class AB amplifier in Hi-Fi field applications, such as home stereo, self powered loudspeakers and Topclass TV. Thanks to the wide voltage range and to the high output current capability it is able to supply the highest power into both 4-Ω and 8-Ω loads.$11.95
Integrated Circuit - SSI2130, VCO, Sound Semiconductor
The FatKeys™ SSI2130 Voltage Controlled Oscillator provides beautiful triangle, sawtooth, pulse, and square waveforms with unprecedented temperature stability; and adds an on-chip mixer, low distortion sine wave generator, through-zero FM/PM capability and more in an ultra-compact PCB footprint.
$8.95 Integrated Circuit - SSI2131, VCO, Sound Semiconductor The FatKeys™ SSI2131 Voltage Controlled Oscillator provides the core VCO function with buffered triangle, sawtooth, and variable-width pulse waveform outputs over a ten-octave range. The device offers unparalleled temperature stability, exponentiality, waveform integrity, and ease of use while requiring an absolute minimum of external components. The SSI2131 is a new-generation voltage controlled oscillator for high-performance electronic musical instruments and other systems requiring accurate audio-band waveform generation. The device offers unprecedented levels of temperature stability, exponentiality, waveform integrity, and ease of use.$7.50
Integrated Circuit - SSI2164, Quad VCA, Sound Semiconductor
The FatKeys™ SSI2164 is perhaps the most flexible VCA available, with four independent channels for lowest cost-per-VCA. The user-selectable mode control allows Class A, AB, or intermediate biasing, and current inputs and outputs provide great design freedom. Ideal for voltage-controlled filters. The SSI2164 is a versatile VCA building block for high-performance audio applications. Four independent channels provide voltage control of current-mode inputs and outputs for a gain range from +20dB to –100dB, with control provided by a ground-referenced –33mV/dB constant. The SSI2164 will directly retrofit existing SSM/V2164 positions while offering improvements that include significantly lower overall distortion, on-chip protection against asymmetrical power failure, and a substantial increase of input current handling. The device offers considerable flexibility for a wide range of design goals and applications.
$6.95 Integrated Circuit - SSI2144, Ladder VCF, Sound Semiconductor The second of two legendary SSM filter updates, the FatKeys™ SSI2144 is a dedicated four-pole low-pass ladder filter with on-chip resonance control. Original designer Dave Rossum did a number of performance updates such as lower noise, improved control feedthrough, and logical pin grouping but otherwise left this sweet-sounding VCF alone. The SSI2144 reprises the SSM2044 of legacy chipmaker Solid State Micro Technology, which many believe to be the best-sounding analog synthesis filter IC ever produced. Based on Dave Rossum’s patented classic improved ladder topology, the SSI2144 allows rich tonal characteristics that showcase the very best attributes of subtractive synthesis. The SSI2144 uses the same internal circuit as the SSM2044 but incorporates improvements by the original designer and takes advantage of modern process technology.$6.50
Integrated Circuit - SSI2140, Multi-Mode VCF, Sound Semiconductor
The SSI2140 is a new-generation voltage controlled filter that provides four highly-configurable variable transconductance cells for a wide variety of pole and mode combinations, and adds significant new features.
$6.50 Integrated Circuit - SSI2162, Dual VCA, Sound Semiconductor The FatKeys™ SSI2162 provides two independent VCA channels, and like its SSI2161 and SSI2164 siblings offers great flexibility in design of dynamics processors, automatic or remote level control, and voltage controlled filters. Highly compact 10-lead SSOP package. The SSI2162 is a versatile VCA building block for high-performance audio applications. Two independent channels provide voltage control of a current-mode input and output for a gain range from +20dB to –100dB, with control provided by a ground-referenced –33mV/dB constant. The device offers considerable flexibility for a wide range of design goals and applications. A unique mode control allows selection of Class A, Class AB, or in-between using a single resistor. In addition, improved current handling allows use of lower value input resistors for reduced output noise without loss of headroom. Both channels can be parallel-connected for further noise improvement.$5.45
Integrated Circuit - SSI2161, Single VCA, Sound Semiconductor
A very high performance single-channel VCA for the most demanding applications, the ProCircuit™ SSI2161 offers industry-leading lowest-noise, and a mode control to optimize noise vs. distortion performance. All at low-cost and in a 10-lead SSOP package. The SSI2161 is a versatile VCA building block for high-performance audio applications. A single channel provides voltage control of current-mode inputs and outputs for a gain range from +20dB to –100dB, with control provided by a ground-referenced –33mV/dB constant. The device offers considerable flexibility for a wide range of design goals and applications. A unique mode control allows selection of Class A, Class AB, or in-between using a single resistor. In addition, improved current handling allows use of lower value input resistors for reduced output noise without loss of headroom.
$5.45 Integrated Circuit - ATtiny45, SN74LS175, 8-bit AVR Microcontroller, 8-pin DIP This microcontroller is a part used in our Relay True Bypass Switching Part 3: Microcontrollers and Current Savings article. To read the full article and learn about a circuit for relay switching in stomp box effects, please see the following link. https://www.amplifiedparts.com/tech-articles/relay-true-bypass-switching-3 The high-performance, low-power Microchip 8-bit AVR RISC-based microcontroller combines 4KB ISP flash memory, 256-Byte EEPROM, 256B SRAM, 6 general purpose I/O lines, 32 general purpose working registers, one 8-bit timer/counter with compare modes, one 8-bit high speed timer/counter, USI, internal and external Interrupts, 4-channel 10-bit A/D converter, programmable watchdog timer with internal oscillator, three software selectable power saving modes, and debugWIRE for on-chip debugging.$1.85
Audio Power Amplifier - LM386N-1, Low Voltage
LM386 Low Voltage Audio Power Amplifier The LM386 is a mono low voltage amplifier that can be used in a variety of applications. It can drive loads from 4 Ω to 32 Ω. The gain is internally set to 20 but it can be modified from 20 to 200 by placing a resistor and capacitor between pins 1 and 8. As this is an Op Amp it can be used in different configurations to fit in several applications. The internal gain setting resistor allows the LM386 to be used in a very low part count system. In addition a series resistor can be placed between pins 1 and 5 to modify the gain and frequency response for specific applications. These are found in many small audio amplifiers and even tiny pedal sized guitar amplifiers! There are tons of possibilities for this little Op Amp.
$1.25 Op-Amp - TL074, Quad, Low-Noise, JFET Input, 14-Pin DIP Low noise JFET quad operational amplifier. Incorporates well matched, high-voltage JFET and bipolar transistors in a monolithic integrated circuit. Features high slew rates, low input bias and offset currents, and low offset voltage temperature coefficients. Features: • Wide common-mode and differential voltage range • Low input bias and offset current • Low noise en = 15 nV/HZ • Output short-circuit protection • High input impedance JFET input stage • Low harmonic distortion: 0.01% • Internal frequency compensation • Latch up free operation • High slew rate: 16 V/us (typical)$1.15
Op-Amp - NE5532, Dual, Low-Noise, 8-Pin DIP
This a high performance dual low noise operational amplifier. Compared to the standard dual operational amplifiers, such as the NJM1458, it shows better noise performance, improved output drive capability, and considerably higher small-signal and power bandwidths. it is compensated internally for voltage follower circuit. This makes the device especially suitable for application in high quality and professional audio equipment, instrumentation, control circuits, and telephone channel amplifiers Features:
• Operating Voltage = ±3V$±22V • Small Signal Bandwidth = 10MHz typ. • Output Drive Capability = 600Ω,10Vrms typ. • Input Noise Voltage = 5nV/√Hz typ. • Power Bandwidth = 140kHz typ. • Slew Rate = 8V/µs typ. • Bipolar Technology $1.15 Integrated Circuit - SN74LS175, Quadruple D-Type Flip-Flops, 16-pin DIP This quad flip flop is a part used in our Relay True Bypass Switching Part 2: Momentary and Soft Touch Switches article. To read the full article and learn about a circuit for relay switching in stomp box effects, please see the following link. https://www.amplifiedparts.com/tech-articles/relay-true-bypass-switching-2 These monolithic, positive-edge-triggered flip-flops utilize TTL circuitry to implement D-type flip-flop logic. All have a direct clear input, and the '175, 'LS175, and 'S175 feature complementary outputs from each flip-flop. Information at the D inputs meeting the setup time requirements is transferred to the Q outputs on the positive-going edge of the clock pulse. Clock triggering occurs at a particular voltage level and is not directly related to the transition time of the positive-going pulse.$1.10 Op-Amp - BA4560, Dual, General Purpose, 8-Pin DIP The BA4560, is a dual operational amplifiers which achieves approximately twice the high output current of the BA4558, as well as featuring a higher slew rate of 4V / µs, a gain band width of 10MHz, and an improved frequency characteristic. 8-pin DIP package. $0.95 Op-Amp - LM741, Single, general purpose, 8-Pin DIP LM741 single opamp in an 8-pin DIP package. The LM741 has been used in classic guitar pedals such as the Distortion Plus. The LM741 series are general purpose operational amplifiers which feature improved performance over industry standards like the LM709. They are direct, plug-in replacements for the 709C, LM201, MC1439 and 748 in most applications. The amplifiers offer many features which make their application nearly foolproof: overload protection on the input and output, no latch-up when the common mode range is exceeded, as well as freedom from oscillations.$0.79 Integrated Circuit - PT2399, Echo / Delay PT2399 echo/delay chip used in many DIY and commercial pedals. The PT2399 is in a DIP 16 package. Minimal external components are required for use and delay time is set with resistance. $0.78 On Backorder Op-Amp - 4558, Dual high-gain, 8-Pin DIP Dual Operational Amplifier. The 4558 integrated circuit is a dual high-gain operational amplifier internally compensated and constructed on a single silicon chip using an advanced epitaxial process. Combining the features of the NJM741 with the close parameter matching and tracking of a dual device on a monolithic chip results in unique performance characteristics. Excellent channel separation allows the use of the dual device in single NJM741 operational amplifier applications providing density. It is especially well suited for applications in differential-in, differential-out as well as in potentiometric amplifiers and where gain and phase matched channels are mandatory. Features: • Operating Voltage (±4V$±18V) • High Voltage Gain (100dB typ.) • High Input Resistance (5MΩ typ.) • Bipolar Technology$0.75
Op-Amp - TL072, Dual, Low-Noise, JFET Input, 8-Pin DIP
The TL072 is a high speed JFET input dual operational amplifier incorporating well matched, high voltage JFET and bipolar transistors in a monolithic integrated circuit. The device features high slew rates, low input bias and offset current, and low offset voltage temperature coefficient.
$0.70 Op-Amp - LF353, Dual, Wide-Bandwidth, JFET Input, 8-Pin DIP Dual wide-bandwidth LF353 opamps in an 8-pin DIP package. The LF353 offers a high input impedance and 3MHz bandwidth. This LF353 device is a low-cost, high-speed, JFET input operational amplifier with very low input offset voltage. It requires low supply current yet maintains a large gain-bandwidth product and a fast slew rate. In addition, the matched high-voltage JFET input provides very low input bias and offset currents.$0.34
Op-Amp - TL062, Dual, Low-Power, JFET Input, 8-Pin DIP
Dual low power opamps in an 8-pin DIP package. The TL062 offers a high input impedance and 1MHz bandwidth.
\$0.28