You are here

Switches

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(11 pages)
S-HM100-ASwitch - Rotary, Voltage Selector, Modern, for Marshall
  • Ratings:

    • IEC: 6.3 A / 250 VAC; 50 Hz
    • UL: 10 A / 250 VAC; 60 Hz
    • CSA: 8 A / 250 VAC; 60 Hz
  • Mounting: Panel Mount from front side
  • Fastening: Screw-on mounting
  • Terminal: Solder
  • Number of Stages: 3
  • Lifetime: 300 operating cycles (without load)
  • Degree of Protection: IP 40
  • Allowable Operation Temp.: -40 °C to 85 °C
  • Climatic Category: 25/85/21 acc.

$29.95
$26.36
You save: 12%
Click to read more
P-H603Switch - for Run Circuit in Hammond Organ

Switch for run circuit in Hammond Organ. Electrical Rating: 16 A - 125 V 8 A - 250 V Dimensions: Mounting Diameter: ½" Bushing Length: 0.425" Length: 1.89" Width: 0.82" Depth: 0.69"


$29.95
$24.95
You save: 17%
Click to read more
P-H1700Switch - Rotary, Impedance Selector, Replacement for Marshall

Rotary impedance selector. Modern, 4/8/16


$26.95
$23.72
You save: 12%
Click to read more
P-SW52Switch - Fender®, Pickup Selector, 5-Way

Whether you need to replace a worn switch or just want to add a little tonal variety to your favorite instrument, Fender&reg offers this high quality, 5 position switch with knob and mounting hardware.


$18.95
$16.68
You save: 12%
Click to read more
P-SW53Switch - Fender®, Pickup Selector, 4-Way Tele Mod

Whether you need to replace a worn switch or just want to add a little tonal variety to your favorite instrument, Fender&reg offers this high quality, 4 position switch with knob and mounting hardware. Telecaster players have long debated the merits of having their pickups wired in parallel vs. in series. In the traditional parallel wiring configuration, pickup output is relatively consistent across all three positions. A Telecaster with its pickups wired in series differs in that when both pickups are on at the same time, the combination produces fatter tone and higher output.


$18.95
$16.68
You save: 12%
Click to read more
S-HM301Switch - Marshall, Toggle, DPST, On-Off, Chrome Tip
Marshall toggle switch, latching 2 position DPST, On-Off. 15A 250VAC rating. Used for Mains and Standby switch in Marshall 1959SLP, 1987X, 2245 and others.

Note: On-Off switches may sometimes be referred to as On-None-Off.
$15.95
$14.04
You save: 12%
Click to read more
P-H1600Switch - Rotary Impedance Selector, for 1600 Series

Includes: 3 pole, 4 position rotary switch, ¼" output jack and black chicken head knob. Hammond 1600 series transformers all provide secondary impedances of 4, 8, or 16 ohms but due to the unique wiring of the secondary, the impedance cannot be changed without rewiring... Until now. We now offer a selector switch, pre-wired and complete with ¼" output jack. Follow simple instructions provided to wire transformer secondary to switch, mount switch and ¼" jack in separate 3/8" diameter holes in chassis and you'll easily be able to select output impedance as necessary.


$14.95
$13.16
You save: 12%
Click to read more
W-SC-W12Switch - Switchcraft, Toggle, 3-way, for Les Paul
One of the most rugged and durable switches available for your Gibson Les Paul or similar two pickup guitars.
$14.95
$13.16
You save: 12%
Click to read more
P-ECB-555Switch - Dunlop, Footswitch, DPDT, Solder Lugs, for MXR

Dunlop® Electronic Components DPDT latching footswitch with solder lugs for MXR and other effects pedals. Made in Mexico.


$14.50
$12.76
You save: 12%
Click to read more
P-H508Switch - Peavey, Rocker, DPST, Lighted

Peavey DPST lighted rocker switch - black base and bezel with red lens, independent 125V neon lamp and six .250in. quick connect tabs. Lamp between terminals '13' and '26'. 16A 125VAC, 16A 250VAC, 10A 28VDC. Made in Mexico.


$14.25
$12.54
You save: 12%
Click to read more

Pages

(11 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Switches